Makita XRU02Z Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita XRU02Z manuals!
Problems with Makita XRU02Z?
Ask a Question
Free Makita XRU02Z manuals!
Problems with Makita XRU02Z?
Ask a Question
Popular Makita XRU02Z Manual Pages
Instruction Manual - Page 1
IMPORTANT: Lire avant usage. INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES
Cordless String Trimmer Coupe herbe sans-fil Desbrozadora Inalámbrica
XRU01 XRU02
012390
IMPORTANT: Read Before Using. IMPORTANTE: Leer antes de usar. 1
Instruction Manual - Page 2
...rate for accidents or hazards occurring to operate the string trimmer has first read the instruction manual. 3. Intended use of starting : −...specifications herein are subject to change without notice. • Specifications and battery cartridge may differ from the string trimmer before
installing the battery pack. Failure to contain long hair.
2. General instructions 1. String trimmers...
Instruction Manual - Page 3
...specifically designated battery packs. Released electrolyte is corrosive and may cause irritation or burns.
6.
Recharge only with a nonslip sole. Check damaged parts...properly repaired or replaced by ...special disposal instructions.
7. Do...manual.
4. 010820
3. Shorting the battery terminals together may create a risk of fire when used with local codes for one terminal to any other part...
Instruction Manual - Page 4
...string trimmer must be used during use the tool in place! 12. Never cut above waist height. 4. Never climb up or out of these chemicals are specially designed to be checked before /after use ) replace strict adherence
to the ground or this
instruction manual...(risk of operation
1. Have the tool repaired only by our authorized service center.
8.
Method of slipping). The ...
Instruction Manual - Page 5
... cartridge with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to drop or strike battery. 9. Overcharging shortens the battery service life.
3. IMPORTANT SAFETY INSTRUCTIONS
ENC007-8
FOR BATTERY CARTRIDGE
1. It may result in locations where the temperature may result in a fire. 8. If electrolyte gets into your eyesight. 5. The...
Instruction Manual - Page 6
PARTS DESCRIPTION
1 4
2 3 5
6
013641
7
8
1 Indication lamp 2 Switch trigger 3 Battery cartridge 4 Front grip
5 Clamping nut 6 Lock grip 7 Guard 8 Nylon cutting head
6
Instruction Manual - Page 7
... always check to see the red indicator on the tool. Red indicator
2. To install the battery cartridge, align the tongue on the front of the following conditions: •...star marking)
1
1. Failure to become overloaded. In this situation, let the battery cool before installing or removing the battery cartridge.
1. FUNCTIONAL DESCRIPTION
WARNING: • Always be seen. If you ...
Instruction Manual - Page 8
...turn the grip counterclockwise until the shaft is provided. To prevent the switch trigger from the string trimmer. battery power is also overloaded and has stopped during operation, the lamp lights up in to... 1: The time at which the indication lamp lights up . Release the switch trigger to replace the battery cartridge when the battery power becomes low. When the tool is almost used
(...
Instruction Manual - Page 9
...replace the nylon cord by following the procedures described under "Installing or removing the Nylon cutting head" and "Winding a new Nylon cord on the guard. NOTE: • The front grip has a edge-to feed out, the cutting head should be bumped against the ground while the tool is a single string trimmer...front grip angle, loosen the claming nut, set the front grip at an proper angle according...
Instruction Manual - Page 10
... cartridge may cause damage to switch off the remaining used Nylon cord from the string trimmer, press in the latches forcefully on the guard. Nylon cord
2. Contact with the notch of the Nylon cutting head installation port on the trimmer and then press in it tightly flat around the spool in the direction of...
Instruction Manual - Page 11
... pulling the Nylon cord. Cutting high
grass at a time. Nylon cord
012399
1 2
012417
After installing the Nylon cutting head, make sure that the Nylon cord comes out by grass
012402
CAUTION: • Do not use the trimmer as if you dig out the
ground with the ground surface. which leads to the...
Instruction Manual - Page 12
... of about 30 ゚ in relation to the section titled "Installing or removing the nylon cutting head" and "Winding a new nylon cord on a slope, make sure
that it locks. Grip
1
012403
Hold the trimmer tilting at the angle of the spool cover and then set the nylon cord again properly by moving the...
Instruction Manual - Page 13
... ground surface. If inspection shows the trouble is parallel to one of normal wear and tear: the tool has been abused, misused or improperly maintained: alterations have other maintenance or adjustment should be sure that the shaft is caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
THIS DISCLAIMER APPLIES BOTH DURING...
Makita XRU02Z Reviews
Do you have an experience with the Makita XRU02Z that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!