Nady microMHT-16X Support and Manuals
Get Help and Manuals for this Nady item
View All Support Options Below
Free Nady microMHT-16X manuals!
Problems with Nady microMHT-16X?
Ask a Question
Free Nady microMHT-16X manuals!
Problems with Nady microMHT-16X?
Ask a Question
Popular Nady microMHT-16X Manual Pages
Manual - Page 1
16-CHANNEL MICRO WIRELESS
SYSTEM
MRX-16 RECEIVER
Instructions for use with any of these transmitters
micro
micro
micro
micro
MGT-16 SYSTEM MHT-16 SYSTEM LINK-16 SYSTEM WHM-16 SYSTEM
MH-16 MT-16A
MT-16R
LK-16
WH-16
Manual - Page 2
...-Worn Transmitter 9 System Operation 10 MRX-16 Wireless Receiver 10 MT-16A/R, MH-16, LK-16, WH-16 Transmitters 12 Miscellaneous Tips 14 Cautions and Troubleshooting 15 MRX-16 System DIP-Switch Frequency Selection Chart 16 Specifications 17 Servicing 18 Warranty 19
Introduction
Thank you for quick convenient setup. Each of your system.
2 The miniature...
Manual - Page 3
...LK-16 Snap-On Transmitter
• Female XLR input connector for mounting transmitter on -the-horn barrel style without any hardwired dynamic microphone • Up to 8 hours battery life)
...; Infrared channel sync with receiver for instant setup • Power On/Off switch; Volume Control; System Features
MRX-16 Systems
• UHF wireless system for musical instrument sounding • 16...
Manual - Page 5
... LED (Red) Flashes once at maximum setting the gain will light indicating the transmitter is locked in and transmitting.
9. Quick User Controls/Connections Guide
MRX-16 Receiver
1. RF SIGNAL LED ...
5 VOLUME CONTROL Adjusts the audio output level-at power up, continuous flashing battery needs replacement
8. POWER SWITCH Select OFF/MUTE/ON (MUTE=power On, audio output highly attenuated)
...
Manual - Page 6
...Insert one second for linking the TX to
reduce the input gain by 15dB for
optimal input level setting. ANTENNA Permanently attached flexible
antenna
25
25. If the IR data download is successful, the receiver SIGNAL...to be backed up , continuous flashing indicates battery needs replacement
20
21. Quick microMGT-16 User Controls/Connections Guide
MT-16A/R Instrument Transmitter
17.
Manual - Page 7
... level setting is turned past minimum and maximum adjustment points it may need to access slot and adjust internal trim-pot with small screwdriver for operation 30. BATTERY COMPARTMENT Insert one AAA battery, observing correct polarity 31. ANTENNA Permanently attached flexible antenna 34. Quick microMHT-16 User Controls/Connections Guide
MH-16 Saxophone (Horn...
Manual - Page 10
... Antenna (5). Note: To insure proper synchronization, the transmitter must always be replaced as soon as indicated by holding the wireless transmitter's IR Receptor/ Sensor Window (21, 31, 46, 56) about... is recommended that the battery is always best to obtain maximum range. There should be replaced after six hours of -sight (no flickering of the selected frequency to the transmitter....
Manual - Page 11
.... When the Volume knob is set at the minimum level before plugging in a light-shielded or darker environment.
Use same procedure with transmitter model supplied with your pedal board or amplifier/mixer as you have completed the above steps, proceed to the following instructions for the transmitter model supplied with your system
When the...
Manual - Page 12
... A fresh AAA alkaline battery generally provides up to achieve desired setting.
12
Turning this trim-pot counterclockwise reduces overall system audio output ...that the battery level is too low and should be replaced after six hours of the arrow. If trim-pot... levels if needed to reduce distortion through the system. To install the battery, push the locking tabs on the transmitter body....
Manual - Page 13
...is now ready for normal use will determine which receiver volume and transmitter input pad settings are not taken during use . For proper operation, the transmitter must be synchronized...A listening test prior to the second (Mute) position. Note: Manually matching the transmitter frequency without the receiver is factory set the receiver power switch to use with the power switch. The ...
Manual - Page 14
...it is very important.
2. Also, since batteries installed for a long period of them :
1. This is not in order to maintain the programmed settings. Do not use . this will provide extra ... possible obstructions between it and the transmitter. When batteries are weak, replace all contacts are not being used with a wireless system. Do not mix new and old batteries, or different types ...
Manual - Page 15
...protected from interference from any other radio services.
Also, for which the Signal LED... sure that wireless frequencies are subject to change the receiver DIP Switches (9) setting to operate .... Especially note that location. Purchasers should all setups. For more information, call the FCC at...the same RF channel. Cautions and Troubleshooting
Low or no protection from interference ...
Manual - Page 17
Specifications
MRX-16 System Frequency Response Dynamic Range Oscillating System Total Harmonic Distortion (THD) RF Carrier Frequency Range Modulation Operating Range
50Hz-16kHz (-3dB) 120dB Phase Lock Loop (PLL)
Manual - Page 18
... 94608
18 If factory service is required, please call our Service Department at 510/652-2411 or e-mail service@nady.com for further instruction before sending in unit. If unit is past the One Year Warranty, The Nady Service Department will not repair nor be held responsible for service or replacement.
DO NOT ATTEMPT TO SERVICE THIS UNIT YOURSELF AS IT...
Manual - Page 19
... or parts, or units damaged by excessive heat, and does not apply to Nady Systems, Inc. This warranty gives you specific legal rights, and you may also have other liability in your bill of incidental or consequential damages, so the above limitations and exclusions may vary from a breach of purchase.
will repair or replace the...
Nady microMHT-16X Reviews
We have not received any reviews for Nady yet.