Pentair Pentair Hydromatic BV-40 Series Cast Iron/Thermoplastic Sewage Pumps Support and Manuals
Get Help and Manuals for this Pentair item
This item is in your list!
View All Support Options Below
Free Pentair Pentair Hydromatic BV-40 Series Cast Iron/Thermoplastic Sewage Pumps manuals!
Problems with Pentair Pentair Hydromatic BV-40 Series Cast Iron/Thermoplastic Sewage Pumps?
Ask a Question
Free Pentair Pentair Hydromatic BV-40 Series Cast Iron/Thermoplastic Sewage Pumps manuals!
Problems with Pentair Pentair Hydromatic BV-40 Series Cast Iron/Thermoplastic Sewage Pumps?
Ask a Question
Popular Pentair Pentair Hydromatic BV-40 Series Cast Iron/Thermoplastic Sewage Pumps Manual Pages
Hydromatic BV40 Submersible Sewage Ejector Pump Manual - Page 1
... or the Canadian Electrical Code. Take extreme care when changing fuses. Do not modify the cord and plug. When using the cord and plug, plug into a grounded outlet only. The pump normally runs hot. DESCRIPTION
This submersible sewage ejector pump is the safety alert symbol.
Installation, Operation & Parts Manual
BV40 Submersible Sewage Ejector Pump
SAFETY INFORMATION
Carefully read...
Hydromatic BV40 Submersible Sewage Ejector Pump Manual - Page 2
...Hazardous voltage. Insert the piggyback plug that will void warranty.
4. When installing, operating, or servicing this cycle until satisfied with your Hydromatic distributor. Plug the pump into sump basin. Attempting to lift or support pump by power cord will easily pass solids. Lifting or supporting pump by power cord can reduce voltage sufficiently to prevent backflow of check...
Hydromatic BV40 Submersible Sewage Ejector Pump Manual - Page 3
... new oil, DO NOT overfill.
Submerge the complete pump in the circuit. When filling with this pump. Set the meter to the "Motor, Switch and Cord Specifications" chart.
The pump will void the pump warranty: 1. Connect or wire pump to its own individual branch circuit with a plastic dowel. Replace the
stator. Remove the two motor leads from the...
Hydromatic BV40 Submersible Sewage Ejector Pump Manual - Page 4
...-cut O-ring and install new square-cut O-ring to prevent any misalignment of vibration.
Motor should run smoothly and be free of the rotor and stator.
4. Pump Disassembly
Oil Fill Plug...the shaft is clean. 7. Assemble the motor housing to prevent contact with high-grade transformer oil (Part No. Replace the oil fill plug. 17. Plug the power cord into the seal plate.
2. Push the...
Hydromatic BV40 Submersible Sewage Ejector Pump Manual - Page 5
... VIEW
1
11 2
3
4 5 10
6 7A,7B 8
9
5738 1207
repair parts list
Key Part
No. Description
Qty
1
Cord 115V 10'
1
1
Cord 115V 20'
1
...Part Number
14623-010-1 14623-020-1 00139-014-1 08507-013-5 00149-001-1
* 14599-001-2 24637D000 05484-001-1 05484-003-1 08498-005-1
2468D000 12752-008-5 12752-009-5 12150-026-5 12150-023-5 13967-025-7 08522-006-3
* If motor fails, replace entire pump...
Hydromatic BV40 Submersible Sewage Ejector Pump Manual - Page 6
... continues to authorized service center. Take unit to malfunction, consult your local serviceman. B. Check for a minimum of overheating. Pump not sized properly. A higher capacity pump may be sure that the arrow on to activate switch or controller.
4. Pump will not shut off:
1.
See installation instructions for switch.
2. If pump is plugged.
7.
D. Be...
Hydromatic BV40 Submersible Sewage Ejector Pump Manual - Page 8
... replaces all labor and shipping charges associated with single phase power through the installing dealer as soon as a problem is not transferable.
HYDROMATIC SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.
EXCEPTIONS: Hydromatic Special Application Pumps, Battery Back-Up Sump Pumps, Filtered Effluent Pumps, Grinder Pumps, and 2-1/2" Sewage Pumps...
Hydromatic BV-40 Submersible Non-Clog Sewage Ejector Data Sheet - Page 1
... maximum performance characteristics without exceeding full load (Nameplate) horsepower.
All pumps have a service factor of Service: GPM:______ TDH:______ and 1280 feet site elevation. Operation is recommended in the bounded area with clear water at 70° F. HYDROMATIC® BV-40 SUBMERSIBLE NON-CLOG, SEWAGE EJECTOR
PERFORMANCE DATA
Wholesale Products Page: 7140-1 Dated: August...
Hydromatic BV-40 Submersible Non-Clog Sewage Ejector Data Sheet - Page 2
Dimensions and weights are approximate. Dimensional data not for international use. HYDROMATIC® BV-40 SUBMERSIBLE NON-CLOG, SEWAGE EJECTOR
DIMENSIONAL DATA
Wholesale Products Page: 7140-2 Dated: August 2002
Supersedes: May 2002
13" (330.2)
13" (330.2)
... unless certified. We reserve the right to make revisions to our product (s) and the product (s) specifications without notice.
Hydromatic BV-40 Submersible Non-Clog Sewage Ejector Data Sheet - Page 3
HYDROMATIC® BV-40 SUBMERSIBLE NON-CLOG, SEWAGE EJECTOR
ELECTRICAL DATA
Wholesale Products Page: 7140-3 Dated: May 2002
MODEL: BV-40
R.P.M. SERVICE FACTOR 1
FULL LOAD AMPS 12.6 MOTOR TYPE MOTOR PROTECTION
1550 OIL FILLED, SPLIT PHASE WITH THERMAL OVERLOAD AUTOMATIC RESET / THERMAL OVERLOAD
HP
VOLTAGE
4/10
115
PHASE 1
NEC CODE -
Hydromatic BV-40 Submersible Non-Clog Sewage Ejector Data Sheet - Page 4
... "O" RINGS
MECHANICAL SEALS Standard:
UPPER BEARING LOWER BEARING
SJTW THERMOPLASTIC CAST IRON CAST IRON
THERMOPLASTIC STEEL STAINLESS STEEL BUNA-N
CARBON / CERAMIC BRONZE SLEEVE SINGLE ROW-BALL
HYDROMATIC® BV-40 SUBMERSIBLE NON-CLOG, SEWAGE EJECTOR
TECHNICAL DATA
Wholesale Products Page: 7140-4 Dated: May 2002
MODEL: BV-40
Physical Data
DISCHARGE SIZE SOLIDS SIZE IMPELLER TYPE CABLE...
Hydromatic BV-40 Submersible Non-Clog Sewage Ejector Data Sheet - Page 5
...GPM/LPS at ________ RPM.
3.01 OPERATING CONDITIONS The pump shall deliver ________ U.S. The pump inlet shall be open and clear, without screening to the pumped liquid shall be 300 series stainless steel. 5. HYDROMATIC® BV-40 SUBMERSIBLE NON-CLOG, SEWAGE EJECTOR
SPECIFICATION DATA
Wholesale Products Page: 7140-5 Dated: May 2002
MODEL: BV-40
1.01 GENERAL Contractor shall furnish all labor...
Hydromatic BV-40 Submersible Non-Clog Sewage Ejector Data Sheet - Page 6
...pump to be operated manually without removal from the sump.
11.01
PAINTING
All cast iron parts shall be Hi-potted
to include the following:
1. USA 293 Wright Street, Delavan, WI 53115 WWW.HYDROMATIC... BV-40 pump is furnished with a water reducible alkyd air dried enamel. All Rights Reserved.
W-01-260 (03/25/13) HYDROMATIC® BV-40 SUBMERSIBLE NON-CLOG, SEWAGE EJECTOR
SPECIFICATION ...
Hydromatic BV-40 Submersible Sewage Ejector Pump Sell Sheet - Page 1
hydromatic® BV-40
Submersible Sewage Ejector Pump
• Manual or automatic operation • Two inch solid handling capability • Residential wastewater and sewage applications
Wide angle float operation available
Improved Diaphragm Switch w w w.hydromatic.com
Hydromatic BV-40 Submersible Sewage Ejector Pump Sell Sheet - Page 2
... and weights are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice.
© 2012 Pentair Ltd.
W-02-7140 (11/16/12) Component dimensions may vary ± 1/8 inch. hydromatic® BV-40
Submersible Sewage Ejector Pump
Pump Characteristics
Pump/Motor Unit Automatic Models Horsepower Full Load Amps Motor Type R.P.M.
Pentair Pentair Hydromatic BV-40 Series Cast Iron/Thermoplastic Sewage Pumps Reviews
Do you have an experience with the Pentair Pentair Hydromatic BV-40 Series Cast Iron/Thermoplastic Sewage Pumps that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Pentair yet.
Earn 750 points for your review!