Ridgid R4030 Support and Manuals
Get Help and Manuals for this Ridgid item
View All Support Options Below
Free Ridgid R4030 manuals!
Problems with Ridgid R4030?
Ask a Question
Free Ridgid R4030 manuals!
Problems with Ridgid R4030?
Ask a Question
Most Recent Ridgid R4030 Questions
Wiring The Switch For R4020 Wet Saw
wire position for switch for Ridgid tile saw R402
wire position for switch for Ridgid tile saw R402
(Posted by jmck0924 1 year ago)
How Do You Replace The Laser Battery?
The laser on my Ridgid R4030 has gone out. How should I go about replacing it?
The laser on my Ridgid R4030 has gone out. How should I go about replacing it?
(Posted by Phat56007 3 years ago)
Noise Level.
R4030 Noise when water is introduced when there is a load or no load, otherwise acceptable noise lev...
R4030 Noise when water is introduced when there is a load or no load, otherwise acceptable noise lev...
(Posted by Uameye 7 years ago)
Replacement Of The Brush In The Motor?
Where can I find the brushes for the motor.
Where can I find the brushes for the motor.
(Posted by luisgc2229 8 years ago)
Ridgid R4030 Videos
RIDGID R4030 Tile Saw
Duration: 2:16
Total Views: 20,035
Duration: 2:16
Total Views: 20,035
RIDGID R4030 7" Job Site Tile Saw with Laser
Duration: 1:19
Total Views: 5,590
Duration: 1:19
Total Views: 5,590
Popular Ridgid R4030 Manual Pages
Operation Manual - Page 1
... the operator's manual before using this product. WARNING:
To reduce the risk of operation, and operator safety. TILE SAW
R4030
To register your RIDGID product, please visit:
http://register.RIDGID.com Pour enregistrer votre produit de RIDGID, s'il vous plaît la visite:
http://register.RIDGID.com Para registrar su producto de RIDGID, por favor visita: http://register.RIDGID.com
Your tile saw...
Operation Manual - Page 3
... a face or dust mask if the cutting operation is damaged must be kept a safe distance from tool before servicing, or when changing attachments, wheels, bits, cutters, etc., all times.
MAINTAIN TOOLS WITH CARE. Keep cord away from receptacle.
Don't use and reduce the risk of moving parts. Also wear protective hair covering to...
Operation Manual - Page 4
... stripes is green with the accessory.
DOUBLE CHECK ALL SETUPS. Never use only identical replacement parts. Do not operate tool when you are tired. Use of accessories that is the equipment-grounding conductor. Always use washers or arbor nuts that have repaired by an authorized service center.
USE ONLY CORRECT WHEELS. Do not rush...
Operation Manual - Page 5
.... f) Do not fill water bath above water fill line.
SAVE THESE INSTRUCTIONS. SPECIFIC SAFETY RULES
SECURE WORK firmly against the miter guide or fence.
NEVER stand or have any work using the saw.
ALWAYS TURN OFF SAW before disconnecting it, to avoid accidental starting when reconnecting to power supply.
THIS TOOL...
Operation Manual - Page 6
...Please study them and learn their meaning. No Hands
Failure to operate the tool better and safer. Read Operator's Manual
To reduce the risk of risk associated with hearing and breathing protection...Indicates a potentially hazardous situation, which , if not avoided, will result in electrocution.
Wet Conditions Alert
Do not expose to comply with ANSI Z87.1 along with this product.
...
Operation Manual - Page 7
....
If damaged replace immediately. Do not operate this product.
ELECTRICAL
EXTENSION CORDS
Use only 3-wire extension cords that have the proper outlet installed by the letters "W-A" or "W" on the cord's jacket. If the saw . This speed is not constant and decreases under a load or with a qualified electrician or service personnel if the grounding instructions are available...
Operation Manual - Page 8
... the ground. These auxiliary protection devices are not on the ground.
The operator should arrange a "drip loop" in the cord connecting the saw to one side of a wall-mounted outlet to the outlet. Disconnect the fuse or circuit breaker that part of the cord below the level of the outlet, or the connector...
Operation Manual - Page 10
... tile cutting wheel is included with sufficient power to scale) are attempting. MITER GUIDE -
This saw ....operator's manual as well as a knowledge of this tool.
Before use cutting wheels rated less than the speed of wheel. SUBMERSIBLE PUMP - Protects user from wheel contact on /off switch. SLIDING TABLE - The submersible pump provide water to -read indicator on the tool and in . TILE...
Operation Manual - Page 12
... not connect to the product by the manufacturer and require customer installation. Failure to possible serious personal injury. If shipping has influenced the settings, refer to modify this tool.
WARNING:
Do not attempt to specific procedures explained in this manual.
If any parts on the water tray frame. From under the water tray...
Operation Manual - Page 16
...Replace the drain plug and refill tray with clean tap water to the fill line.
FILL LINE
WATER RESERVOIR
Fig. 15
DRAIN PLUG
Fig. 16
16 -
For best performance, set the flow to "Max" to get wet... the pump. English
WATER FLOW SELECTOR
MIN
MAX
MAX
MIN Fig. 17 To change reservoir water: Unplug the saw. Remove the drain plug and empty waste water into the wheel. Do...
Operation Manual - Page 17
... indicators inside the battery compartment. Replace the battery compartment cover. BATTERY COVER
AAA AAA
SCREW
• To reduce the risk of the supplied arbor wrench. Make several practice cuts on the tile. ASSEMBLY
DANGER:
Laser radiation. Remove cover and set aside. Install two AAA batteries according to the tool before servicing, when changing cutting wheels, or...
Operation Manual - Page 19
...wet before removing any part of the material at the same time turning the lock knob clockwise to be cut on track. CROSS CUT
SLIDING TABLE FENCE
MITER GUIDE...tile and mark the tape. Clean the saw table and miter guide frequently during use the miter guide whenever possible.
A common problem when cutting tile...is made , turn the saw OFF.
OPERATION
To lock the motor head:...
Operation Manual - Page 20
...Install the miter guide to the left of the wheel. Set the miter guide to a complete stop before turning on the bottom or underneath side of the material.
20 - English
MITER CUT
L-CUT
Fig. 24
Fig. 25 OPERATION... on the saw OFF. Wait for
the wheel to "creep" during cutting. TO MAKE AN L-CUT
See Figure 25. Miter cuts tend to get wet before removing any part of the ...
Operation Manual - Page 23
...using the laser guide. Use the work clamp or a C-clamp to secure a piece of
scrap tile. Plug the saw into ... Unplug the saw housing. NOTE: Always make a slight
cut to score the tile. Release the switch trigger and allow the saw blade to
stop...°: Set the saw arm to the table and the hex bolt is resting on the saw . Turn on the saw . NOTE: These...
Operation Manual - Page 26
The replacement tool will repair any faulty workmanship, and either repair or replace any malfunction, failure or defect resulting from state to RIDGID® hand held and stationary power tools purchased 2/1/04 and after the date of purchase, if you must be presented when requesting warranty service. When requesting warranty service, you are disclaimed.
RIDGID®, INC. MAKE ...
Ridgid R4030 Reviews
We have not received any reviews for Ridgid yet.