Sanyo XF45 - PLC XGA LCD Projector Support and Manuals
Get Help and Manuals for this Sanyo item
Sanyo XF45 Videos
Sanyo PLC-XF45 Projector
Duration: :55
Total Views: 73
Duration: :55
Total Views: 73
Popular Sanyo XF45 Manual Pages
Instruction Manual, PLC-XF45 - Page 1
Owner's Manual
Multimedia Projector
MODEL PLC-XF45
✽ Projection lens is optional.
Instruction Manual, PLC-XF45 - Page 2
... must be dangerous.
Heat build-up can reduce the service life of your projector seems to indicate laser emission).
NO USERSERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. TO THE OWNER
Before operating this projector, read this manual again, check operations and cable connections and try the solutions in the "Trouble-shooting" section of the end of this booklet. Improper...
Instruction Manual, PLC-XF45 - Page 3
... dangerous voltage points or short out parts that the projector is left unattended and unused for service.
Refer all of any service or repairs to this unit to qualified service personnel. c. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.
3 This projector should never be sure the service technician has used replacement parts specified by placing the...
Instruction Manual, PLC-XF45 - Page 6
...display (LCD) technology. This function helps you purchased a projector.
It can be controlled and set up ... this problem by digitally altering projection to turn Projection Lamp off when a projector detects signal...setup is necessary and projection is no need for optional parts.
6
x Power Management
Power Management function is provided to reduce power consumption while a projector...
Instruction Manual, PLC-XF45 - Page 21
...of image. [Normal / True / Wide / Digital zoom +/-] (Refer to P34)
SETTING MENU
Used to change settings of selected video source. (Refer to P36)
IMAGE ADJUST MENU
Used to adjust picture ...GUIDE WINDOW
Shows selected item of image to Normal or Wide. (Refer to select input source (Input 1, Input 2, Input 3 or Input 4).
AV SYSTEM MENU
Used to select system of projector or reset Lamp Replace...
Instruction Manual, PLC-XF45 - Page 22
... bright and READY indicator turns off .
indicator flashes red, projector is automatically turned off .
LAMP indicator lights RED, and READY indicator lights GREEN. LAMP indicator dims, and Cooling Fans start to flash, contact sales dealer where you purchased this projector or service center.
22 TURNING OFF PROJECTOR
1 Press POWER ON-OFF button on Side Control or...
Instruction Manual, PLC-XF45 - Page 29
... to page 30, 31.) q Auto PC Adjustment function cannot be fully adjusted with this projector. icon and press SELECT button.
29 This Auto PC Adjustment can be done just by ...sync, Total dots and Picture Position of MANUAL PC ADJUSTMENT section (P30).
When image is not provided properly through this function, manual adjustments are memorized, setting can
not be operated in this Auto ...
Instruction Manual, PLC-XF45 - Page 30
... picture position.
This projector has 5 independent memory areas to match your PC image. This enables you use it. Note : This PC ADJUST Menu cannot be tuned by Multi-Scan system of this icon to item and press SELECT button. Press POINT LEFT/RIGHT button to recall setting for a specific computer whenever you to...
Instruction Manual, PLC-XF45 - Page 42
...Do not reset Lamp Replace Counter except after Projection lamp is replaced.
NOTE: Before you control a projector by computer, install USB driver (optionally sold parts) and set up computer following steps below. Lamp counter reset
Be sure to reset Lamp Replace Counter. Message "Lamp replace counter Reset?"
NOTE: Be sure to reset correct lamp number otherwise LAMP REPLACE indicator...
Instruction Manual, PLC-XF45 - Page 43
...that mouse driver is properly installed in your computer to Control Port of a projector with Control Cable for connection.)
2 Turn a projector on ...projector is moved corresponding with POINT button, SELECT button, and RIGHT CLICK button on after performing above checks, Cooling Fans or Internal Circuits may not work properly. Contact service personnel from an authorized dealer or a service...
Instruction Manual, PLC-XF45 - Page 45
... and those lamps are out, a projector operates with 1 lamp. Lamp Mode Changeover
Lamp Management Function automatically changes combination of lighting lamp (Lamp Mode) by Lamp Management Function. LAMP STATUS
INPUT 1 13 24
30
LAMP REPLACE INDICATOR
Lamp Replace Indicator
This LAMP REPLACE indicator lights yellow when any of Projection Lamps is nearing its end. Refer to SETTING section on...
Instruction Manual, PLC-XF45 - Page 46
... is not replaced. LAMP 2
8
Reset Lamp Replacement Counter. (Refer to be replaced on Lamp Status Display.
Make sure which number of lamp needs to section "Lamp Counter Reset" on . REPLACE
LAMP
LAMP REPLACE INDICATOR
LAMP READY RWELTAPAERLMMANPPCIN.EG
Allow a projector to a projector and turn a projector on page 42.)
NOTE : Do not reset LAMP REPLACEMENT COUNTER when lamp is set...
Instruction Manual, PLC-XF45 - Page 47
... carefully.
q Model No.
q A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to the environment or conditions in the LAMP REPLACEMENT section of this manual. ) Continuous use . Risk of explosion may increase the risk of use of your projector
:
q Replacement Lamp Type No. :
PLC-XF45
POA-LMP49
(Service Parts No...
Instruction Manual, PLC-XF45 - Page 48
... needs cleaning. If problem still exists, check following chart. q Check WARNING TEMP. q When turning a projector on page 22.)
q Check Projection Lamp. (Refer to ON. q Check audio cable connection from a cool temperature location to OFF, make sure a projector works as described in section "CONNECTING PROJECTOR" on page 40.)
q Check connection between your dealer or service center for...
Instruction Manual, PLC-XF45 - Page 49
.... q Check transmitted signal mode from a projector when using Remote Control Unit. Do not attempt to obtain service. If after following all operating instructions, you find that service is Listed by Underwriters Laboratories Inc.
This symbol on your computer. q Check mouse setting on the nameplate means the product is necessary, contact Sanyo Service Station or store where you...
Sanyo XF45 Reviews
We have not received any reviews for Sanyo yet.