Sharp AN-PHCM20 Support and Manuals
Get Help and Manuals for this Sharp item
View All Support Options Below
Free Sharp AN-PHCM20 manuals!
Problems with Sharp AN-PHCM20?
Ask a Question
Free Sharp AN-PHCM20 manuals!
Problems with Sharp AN-PHCM20?
Ask a Question
Popular Sharp AN-PHCM20 Manual Pages
Installation Instructions - Page 1
AN-PHCM20
INSTALLATION INSTRUCTIONS FOR MOUNTING BRACKET FOR USE ONLY WITH SHARP PROJECTOR MODEL XG-PH50X CEILING MOUNTING BRACKET AN-PHCM20
CEILING MOUNTING BRACKET COMBINED WITH OPTIONAL ADJUSTABLE EXTENSION TUBE MODEL AN-EP101B
COPYRIGHT © 2005 SHARP ELECTRONICS CORPORATION
Installation Instructions - Page 2
...PARTS LIST FOR MODEL AN-PHCM20 CEILING BRACKET (SEE FIG. 1)
ITEM
DESCRIPTION
A.
M4 X 12mm MOUNTING SCREWS FOR USE WITH ATTACHMENT PLATE
J.
LOCKING HEX NUT & WASHER
D.
THE ACCESSORIES REFERRED TO IN THESE INSTRUCTIONS ARE
INTENDED FOR USE ONLY WITH COMPATIBLE SHARP PROJECTORS. STEEL CEILING MOUNTING PLATE WITH SECURITY FITTING
E. SEE SHARP PROJECTOR OWNER'S MANUAL OR SHARP...
Installation Instructions - Page 3
...H. INVERT THE PROJECTOR IMAGE
Please refer to the owners manual for your SHARP LCD PROJECTOR for the ceiling bracket has been determined, (see LCD PROJECTOR Owner's Manual), make sure to accommodate its use in the ceiling.
STEP 1. INSTALLATION INSTRUCTIONS
CEILING BRACKET AN-PHCM20
FIGURE 1.
C.
G.
INSTALLATION OF THE METAL CEILING BRACKET
After the location for information...
Installation Instructions - Page 4
... unit.
PAGE 4 FIGURE 2. Two sizes of the beam. (See Figs. 2 and 3).
1.2 Screw the ceiling plate to insure a vibration-free support. (See Figs. 2 and 3).
INSTALLATION INSTRUCTIONS
CEILING BRACKET AN-PHCM20
1.1 a. Use shorter screws for the support screws using a 1/8" drill bit into the center of hex head lag bolts are provided.
CAUTION: THE BRACKET MOUNTING SCREWS MUST...
Installation Instructions - Page 5
... used the with Optional Security Cable Kit Model AN-CMCSS16 or AN-CMCSS46
Access Hole Template Label
Press Velcro Tabs together to secure plastic trim cover in position
PAGE 5 Use a very sharp cutting tool.
2.4 Thread the cable through the access hole in - INSTALLATION INSTRUCTIONS
CEILING BRACKET AN-PHCM20
FIGURE 3 ILLUSTRATION OF SINGLE BEAM CEILING BRACKET...
Installation Instructions - Page 6
...
All other mounting holes on the projector case.
4.2 Install the three M4 x 12mm long screws provided.
INSTALLATION INSTRUCTIONS
CEILING BRACKET AN-PHCM20
STEP 3 DETACH THE POSITIONING ASSEMBLY FROM THE PROJECTOR ATTACHMENT ...from the bottom knuckle which is part of the attachment plate. (See Fig. 5)
REMOVE NUT LOWER KNUCKLE
SPECIAL NOTE TO INSTALLERS: The positioning knuckle is mounted ...
Installation Instructions - Page 7
INSTALLATION INSTRUCTIONS
CEILING BRACKET AN-PHCM20
STEP 5 ATTACH THE POSITIONING ASSEMBLY TO THE CEILING PLATE
FIGURE 8
WASHER LOCKING NUT UPPER KNUCKLE
IF YOU INTEND TO RUN AUDIO... open end wrench or an crescent wrench.
PAGE 7 ALL WIRING MUST COMPLY WITH THE NEC AND ALL LOCAL BUILDING, ELECTRIC, AND SAFETY CODES.
adjustable
DO NOT RUN THE AC POWER CORD INSIDE THE PLASTIC TRIM COVER.
Installation Instructions - Page 8
... the projector to hold the set position. 7.1 After the projector has been property wired, turn it on lock base.
PAGE 8
Threaded hole lines up but do not tighten all the way.
INSTALLATION INSTRUCTIONS
CEILING BRACKET AN-PHCM20
STEP 6 HANGING THE PROJECTOR FROM POSITIONING ASSEMBLY
IT IS RECOMMENDED THAT TWO PERSONS SUPPORT THE PROJECTOR WHEN RAISING...
Installation Instructions - Page 9
... THE NEC AND ALL LOCAL BUILDING, ELECTRIC AND SAFETY CODES.
NOTE: IN THE EVENT YOU WISH TO USE THE SHARP ADJUSTABLE EXTENSION ACCESSORY IN CONJUNCTION WITH THE CEILING MOUNTING BRACKET, PLEASE REFER TO THE INSTALLATION INSTRUCTION MANUAL INCLUDED IN THE EXTENSION TUBE PACKAGE. INSTALLATION INSTRUCTIONS
CEILING BRACKET AN-PHCM20
FIGURE 11 DETAIL OF POSITIONING ASSEMBLY
CEILING PLATE
PLASTIC...
Installation Instructions - Page 10
...center of lens to bottom of projector 6 1/2" F. SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
PAGE 10 INSTALLATION INSTRUCTIONS
CEILING BRACKET AN-PHCM20
DIMENSIONS AND MEASUREMENTS OF COMPONENTS FOR SHARP MOUNTING BRACKET AN-MBCM10
CEILING PLATE 4" WIDE X 18" LONG DISTANCE BETWEEN SETS OF MOUNTING HOLES: 1st SET 12", 2nd SET 14", 3rd SET 16" ADDITIONAL POSSIBLE COMBINATIONS OF MOUNTING HOLE...
Installation Instructions - Page 11
..., will be free from date of purchase.
INSTALLATION INSTRUCTIONS
CEILING BRACKET AN-PHCM20
ONE YEAR LIMITED WARRANTY
SHARP Electronics Corporation warrants to the first end use purchaser, that it will, at its option, either repair the defect or replace the defective product or part thereof at no event shall SHARP be granted to purchasers by anyone other than...
Installation Instructions - Page 12
COPYRIGHT © 2005 SHARP ELECTRONICS CORPORATION
Installation Instructions - Page 13
CONTINUE WITH STEP 5 OF THE INSTALLATION INSTRUCTIONS.
COPYRIGHT © 2005 SHARP ELECTRONICS CORPORATION AN-PHCM20
SUPPLEMENTAL INSTRUCTIONS FOR INSTALLATION OF 2" EXTENSIONS TO LOWER MOUNTING BRACKET FROM CEILING. CEILING PLATE COVER
INSTALL ONE 2" EXTENSION OR TWO 2" EXTENSIONS HERE AS NEEDED.
Sharp AN-PHCM20 Reviews
We have not received any reviews for Sharp yet.