TASCAM FE-8 Support and Manuals
TASCAM FE-8 Videos
Popular TASCAM FE-8 Manual Pages
Manual - Page 1
... NO USER-SERVICEABLE PARTS INSIDE. Model number
Serial number
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
D00748600B
FireWire Control Surface Expander
OWNER'S MANUAL
Ü
... presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a serial number located on the rear ...
Manual - Page 3
...fallen into your safety. Servicing is required when the ...INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Head all warnings.
4 Follow all instructions.
5 Do not use this apparatus during lightning storms or when unused for replacement... as radiators, heat registers, stoves, or other . TASCAM FE-8 Owner's Manual 3 Install in the off position. If the provided plug does not...
Manual - Page 4
...not provided with the following code:
GREEN-AND-YELLOW BLUE ...and, if not installed and used and...replacing the fuse only a correctly rated approved type should be used in diesem Fall kann vom Betrieber verlang werden, angemessene Maßnahmen durchzuführen und dafür aufzukommen.
4 TASCAM FE-8 Owner's Manual...Part 15 of this apparatus may not correspond with the instruction manual...
Manual - Page 5
...-1884 Setup Guide ("Installation (Windows 2000 and Windows XP)" on page 7, "Installation (Mac OS 9.2)" on page 9 and "Installation (Mac OS X 10.2.4 and above)" on page 8 until the FE-8 has been installed and connected as the new installation overwrites the old settings. lowing the instructions in "Installation using . This is recognized by the FW-1884's driver. Instead, the FE-8 is designed...
Manual - Page 6
....
1
2
5 Replace the two screws removed at the start of electric shock under other conditions (that end cheek from the AC power supply and computer. When the end cheeks are removed from the FW-1884, some sharp metal edges are seated in the instructions here.
Physical installation
WARNING
Before undertaking this procedure.
6 TASCAM FE-8 WARNING
The FE...
Manual - Page 7
...
FW-1884 and the FE8. Cheap cables may not meet the interface specifications and may be used for connection to the FW-1884 or other end to number devices or set IDs, etc. Instead...correct location relative to link the FE-8 units, and replace the end cheek(s) only on the rear panel of the IEEE 1394 cable supplied with an FW1884 unit. Physical installation-Updating the software
6 There is ...
Manual - Page 8
...passed back from the DAW to begin editing.
Select a unit in the list.
8 TASCAM FE-8
Any FE-8 units connected to keep track of the Windows version). Highlight a unit in the list ...Software and the FE-8
Each FE-8 unit in which controller information is passed to the DAW application, and status information (fader position, indicator status, etc.) is not part of the different ...
Manual - Page 9
... and physical specifications
Power Requirement
Power Consumption Peak inrush current Applicable electromagnetic environment Dimensions (W xHxD) Weight Supplied accessories
100V AC, 50-60Hz 120V AC, 60Hz 230V AC, 50Hz...x 133 x 478 (mm) 10.25 x 5.2 x 18.9 (in.) 5 kg (11 lbs.) IEEE 1394 cable, mounting pad (sheet joint), AC power cable
133mm (5.2")
478mm (18.9")
260mm (10.2")
TASCAM FE-8 9 4 -
Frequently Asked Questions - Page 1
...computer, then connect the FE8 to the FW-1884?
You would all operating systems? Q: Do HUI and Mackie Control modes work with the FE-8?
First, click on the FE-8 in the list ...setup.
A: No, it shows
up in the list to support the FE-8. Q: How does the FE-8 show up and down in the software? Q: How does it easily in the FW-1884 driver?
A: Both the FW-1884 and FE-8 each FE...
TASCAM FE-8 Reviews
Do you have an experience with the TASCAM FE-8 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for TASCAM yet.
Earn 750 points for your review!