Adaptec 2010S - SCSI RAID Storage Controller Support and Manuals
Get Help and Manuals for this Adaptec item
View All Support Options Below
Free Adaptec 2010S manuals!
Problems with Adaptec 2010S?
Ask a Question
Free Adaptec 2010S manuals!
Problems with Adaptec 2010S?
Ask a Question
Popular Adaptec 2010S Manual Pages
Installation Guide - Page 7
...an Existing Linux System 3-10 Installing a Newer Driver 3-12
4 Installing Storage Management Software
System Requirements 4-2 Linux Considerations 4-2
Installing Storage Manager 4-3 Operating System Compatibility 4-3
A Card and Module Diagrams
Adaptec SCSI RAID 2010S A-1 Adaptec SCSI RAID 2015S A-2
B Troubleshooting
C Controller Reset Procedures
NVRAM Reset C-2 Flash Mode 0 C-2
D Specifications
vi
Installation Guide - Page 9
... SCSI RAID 2010S/2015S Installation Guide
System Requirements
The following system requirements are discussed:
■ Storage requirements for the 2010S and 2015S.
Storage Requirements for Drivers and Software
Adaptec Storage Management software and device drivers require approximately 5 MB of the devices is at a reduced level of the supported EMRL-
The Adaptec ZCR controllers...
Installation Guide - Page 10
... controllers support: ■ RAID levels 0, 1, 5, multilevel 10 and 50, JBOD (Just a Bunch Of
Drives). ■ Fixed cache memory with Error Correction Code (ECC). ■ Predictive caching capability. ■ PCI Local Bus Specification, Revision 2.2 with all SCSI devices of SCSI devices older than Ultra 2 is not suggested. Kit Contents
Your Adaptec controller kit includes: ■ ASR-2010S...
Installation Guide - Page 11
... the Adaptec Storage Management Software User's Guide for more information.
■ Legacy SCSI devices (including hard disk, tape, CD-ROM, CD-RW, and Magneto-Optical drives) and jukeboxes.
■ SCSI Accessed Fault-Tolerant Enclosure (SAF-TE) and SCSI Enclosure Services (SES) for high-availability Local Area Network (LAN) servers and storage subsystems.
■ Adaptec RAID software supports up...
Installation Guide - Page 12
...-based ZCR controller (2010S) is not installed, but Adaptec's ZCR controllers can only be hidden and controlled only by the ZCR controller Input/Output Processor (IOP) when the Adaptec PCI-based ZCR controller is installed.
1-5 Note: Neither the ASR-2010S or the ASR-2015S will function when used with an I2O RAID BIOS and SMOR. Once installed, the ZCR hides the normal SCSI BIOS and replaces it...
Installation Guide - Page 14
...Storage Manager provides online help displays.
Identify the scenario that your motherboard is compatible with the controller. Refer to Chapter . 5 Install the controller driver according to set for Adaptec ZCR controllers consists of the following steps provide an overview of the process of the Installation Process
The following : ■ Adaptec SCSI RAID 2010S/2015S Installation Guide...
Installation Guide - Page 15
....com
Furthermore, Adaptec Storage Management provides additional features, such as Simple Network Mail Protocol
(SNMP) and Desktop Management Interface (DMI) agents.
■ RAIDUTIL CLI-Provides the same functions as a utility that is not available. Adaptec SCSI RAID 2010S/2015S Installation Guide
Storage Management Software Overview
Adaptec supplies a number of the controller's BIOS code.
Installation Guide - Page 19
... are typically set using Ultra320 SCSI devices and good quality LVD SCSI cables. The wide bus is not necessay to assign an ID to each SCSI device.
2-2 Wide devices allow data to your Adaptec ZCR controller. Note: Adaptec ZCR controllers cannot be used with older SCSI 5-V differential (DE) devices.
Adaptec SCSI RAID 2010S/2015S Installation Guide
Narrow and Wide SCSI Devices
You...
Installation Guide - Page 20
... SCSI BIOS. If necessary, the Adaptec ZCR controller ID can also use ID 7). Use SMOR or the Configure Host Bus Adapter window in this chapter along with the contents of your motherboard guide for your combination.
2-3 SCSI Termination
The basics of a
SCSI cable. Any termination settings made or recommended in Adaptec Storage Management to be accomplished by default (most SCSI controllers...
Installation Guide - Page 21
... has only these termination settings:
Setting On Off
Function
Default-Enables the controller termination built.
Use only if the controller will not be terminated properly for a single bus.
Adaptec SCSI RAID 2010S/2015S Installation Guide
SCSI termination is configured through the SMOR utility or from the Configure Host Bus Adapter window in the controller. Note: Each channel...
Installation Guide - Page 35
...system drives prior to be reinstalled after installing the ZCR controller.
3-8 Adaptec SCSI RAID 2010S/2015S Installation Guide 6 When prompted, click Have Disk. 7 Select Adaptec I2O RAID Host Adapter Driver for installing the Adaptec ZCR controller with Red Hat Linux. ■ Installing the Driver in a New Linux System on page 3-9 ■ Installing the Controller in an Existing Linux System on...
Installation Guide - Page 36
...To install the Adaptec ZCR controller: 1 Install and configure your preferred environment;
The operating system can manually partition the drives. During startup, press Ctrl+A to create the RAID. If your preferred language and keyboard type. 7 Continue with the ASR-2010S or ASR-2015S. Installing the Driver
Installing the Driver in a New Linux System
The drivers for installing the...
Installation Guide - Page 37
... up , it will be prompted to the instructions in Chapter 2. Press the appropriate key to enter into Kudzu when prompted.
6 When asked about the newly detected RAID controller, allow Kudzu to an existing system is inserted. Adaptec SCSI RAID 2010S/2015S Installation Guide
Installing the Controller in an Existing Linux System
Adding the controller to configure the device. Make any hard disk...
Installation Guide - Page 47
..., refer to enable the EBDA Relocation option. Use SMOR to Appendix C. Adaptec SCSI RAID 2010S/2015S Installation Guide
After updating the Adaptec controller firmware or BIOS and restarting, the controller does not respond. Reset the NVRAM to disable Boot Enable for the system. However, during the boot process, set Bootable Devices to Boot from being used to Appendix C. Use SMOR to...
Installation Guide - Page 49
Adaptec SCSI RAID 2010S/2015S Installation Guide
NVRAM Reset
Adaptec ZCR controllers retain their default settings by using SMOR's Default command or RAIDUTIL's -X command. If this happens, the parameters stored in the NVRAM can be put into a state where it hangs ...
Adaptec 2010S Reviews
We have not received any reviews for Adaptec yet.