Bosch 3814 - 14 Inch Abrasive Cut Support and Manuals
Get Help and Manuals for this Bosch item
Popular Bosch 3814 Manual Pages
Operating Instructions - Page 2
...using alcohol or other competent repair service.
• THE USE OF ANY OTHER ACCESSORIES NOT SPECIFIED IN THIS MANUAL MAY CREATE A HAZARD. ...blade or cutter against the direction of rotation of power and overheating.
General Safety Rules - with grounded surfaces. Loose clothes, jewelry or long hair can result in moving parts. Make sure the switch is the same as the specific...
Operating Instructions - Page 3
...power sanding, sawing, grinding,...Install a new wheel if tool was dropped. Proper support of a smaller tool, these chemicals are not intended to avoid chipping or cracking. Abrasive wheels cut off machine near flammable materials. WARNING
"READ ALL INSTRUCTIONS" Failure to friction heating.
• Do not set...8226;) symbol listed BELOW and other...blade or standard wood cutting toothed blades...
Operating Instructions - Page 4
...repair or replacement...14 18 16 14 12 18 16 14 12 16 16 14 12 14 12 - -
240 VOLT A.C.
have a qualified electrician replace the TWO-prong outlet with a 3-conductor cord and grounding type plug, approved by the Canadian Electrical Code.
Extension Cords
RECOMMENDED SIZES OF EXTENSION CORDS
Tool's Ampere Rating
3-6 6-8 8-10 10-12 12-16
120 VOLT A.C. "SAVE THESE INSTRUCTIONS... installing ...
Operating Instructions - Page 5
...14" WHEEL . . . For easier carrying.
7. For quick and easy clamping.
9. Your tool is used for the depth stop adjustment bolt. The small end of your cutting requirements.
1. LOCKING TRIGGER SWITCH...properly during cutting operation.
5. HANDLE . . . For setting wheel to 45º for angle cuts.
8. ADJUSTABLE DEPTH...ON" BUTTON
5 HANDLE
2 TRIGGER SWITCH
1 SPINDLE LOCK
CORD
4 WHEEL ...
Operating Instructions - Page 6
...Instructions
TRIGGER SWITCH WITH "LOCK-ON" BUTTON Your tool can accommodate a padlock with a shackle of abrasive wheel by squeezing or releasing the trigger. The "LockON" is continuously being depressed, the trigger cannot be turned "ON" or "OFF" by rotating counter-clockwise with the wrench provided.
2. NOTE: Switch can be released.
Removing and Installing...
Whenever replacing a ...
Operating Instructions - Page 7
...: To maintain adjustment, securely tighten nut on arm.
2. Raise the depth stop bolt clockwise. Loosen the vise stop bolt. As the wheel wears, or when replacing a wheel it will be damaged. CAUTION
Be certain that the hold down . QUICK RELEASE LEVER To release work, turn crank to loosen, lift quick release...
Operating Instructions - Page 8
... service. Cleaning
! tively with a clean cloth and mild soap to prevent deterioration from oil and grease.
After each use . Ventilation openings and switch levers must be replaced... mm (14") outer diameter x less than 4.5 mm (3/16") thickness x 25.4 mm (1") hole diameter
Workpiece Configuration (Cross-Section)
Maximum Cutting Capacity (a)
-8- Only genuine Bosch replacement brushes specially...
Parts List - Page 2
...
9
Support Bracket
62
Clamp Plate
80
Plate
9
Label "Warning"
9
Post {4}
9
Upper Guard
92
Label "Depth"
9
Label "Warning"
9
Bolt
89
Side Cover
92
Support Bracket
62
Wrench
9
Motor Housing Assembly 71
w/pos. 16, 62, 85
Brush Set
26
Handle Assembly
74
+ = Not Illustrated * = As Required F/C = Failure Code AW = Refer to AW Labor Time Chart 3814 CHOP SAW
Pos...
Bosch 3814 Reviews
We have not received any reviews for Bosch yet.