Campbell Scientific CS215 Support and Manuals
Get Help and Manuals for this Campbell Scientific item
This item is in your list!
View All Support Options Below
Free Campbell Scientific CS215 manuals!
Problems with Campbell Scientific CS215?
Ask a Question
Free Campbell Scientific CS215 manuals!
Problems with Campbell Scientific CS215?
Ask a Question
Popular Campbell Scientific CS215 Manual Pages
CS215 Temperature and Relative Humidity Probe - Page 1
CS215 Temperature and Relative Humidity Probe
Revision: 7/12
Copyright © 2005-2012 Campbell Scientific, Inc.
CS215 Temperature and Relative Humidity Probe - Page 3
...OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Warranty
"PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. are warranted only to be the sole and exclusive remedy under this warranty is not liable for installation services performed by Campbell such as programming to customer specifications, electrical connections to Campbell. Products not manufactured, but that are re-sold by...
CS215 Temperature and Relative Humidity Probe - Page 4
...service on the outside of Product Cleanliness and Decontamination" form and comply with the requirements specified in countries served by Campbell Scientific, Inc. Campbell Scientific reserves the right to the customer at www.campbellsci.com/repair...for customers within three days of the problem, an RMA number will be issued. Campbell Scientific's shipping address is unable to process...
CS215 Temperature and Relative Humidity Probe - Page 6
... 23
8.1 Sensor Element Replacement 24
9. CS215 and 41303...8-1. Environmental Tests A-1
ii Incorrect fit of sensor element (side view 26 8-2. Connections to Campbell Scientific Dataloggers 10 A-1. Screen capture of SDI-12... "Edlog" Dataloggers 22
8. CS215 and 41303-5A Radiation Shield on a CM200 Series
Crossarm 3 7-1. Troubleshooting 27
10. CS215 Table of SDI-12 Transparent Mode...
CS215 Temperature and Relative Humidity Probe - Page 7
... company.
• The model number and cable length are available in air. Initial Inspection
• Upon receipt of the cable. Introduction
The CS215 Temperature and Relative Humidity probe is easily broken if bent or knocked.
3. If damage to temperature extremes, moisture, and UV degradation.
File damage claims with a Campbell Scientific applications engineer.
• Although...
CS215 Temperature and Relative Humidity Probe - Page 10
Select a datalogger and scan interval.
4 CS215 Temperature and Relative Humidity Probe
4.2 Step 2 - Open Short Cut and click on New Program.
2. Use SCWin Short Cut to Program Datalogger and Generate Wiring Diagram
The simplest method for programming the datalogger to measure the CS215 is to use Campbell Scientific's SCWin Short Cut Program Generator. 1.
CS215 Temperature and Relative Humidity Probe - Page 12
..., applies temperature and linearization corrections to the wiring diagram generated by SCWin Short Cut.
5.
Replacement of the element effectively fully recalibrates the probe both a temperature and RH sensor. Overview
The CS215 probe uses a single chip element that incorporates both for the AirTC and RH and then select finish.
6. Wire according to the
6 Choose the outputs...
CS215 Temperature and Relative Humidity Probe - Page 13
... and to fit into a range of the sensor.
The probe's cable can terminate in:
• Pigtails that connect directly to a Campbell Scientific datalogger (option -PT).
• Connector that attaches to www.campbellsci.com/prewired-enclosures for the CS215 is specified when the sensor is ordered. CS215 Temperature and Relative Humidity Probe
readings and presents the data via a 2 ft...
CS215 Temperature and Relative Humidity Probe - Page 16
...length.)
There are two ways to set the SDI-12 address of the CS215:
• By sending the required commands to the sensors via an SDI-12 recorder/datalogger that...sensors. Using the SDI-12 address minimizes the use more than one probe per datalogger, you can either no offset errors incurred with long cables follow these guidelines:
10 TABLE 7-1. Wiring
Connections to Campbell Scientific...
CS215 Temperature and Relative Humidity Probe - Page 17
... Campbell Scientific). This instruction usually takes less than 70 µA of the datalogger can be upgraded to the CS215 on the type and model of the SDI-12 1.3 instruction set. For CRBasic dataloggers, the SDI12Recorder() instruction is automatically sent by turning the 12 V supply to do this is measured using the sensor with a subset of your system's documentation. Specifically...
CS215 Temperature and Relative Humidity Probe - Page 18
... aR! If measurements are no errors. option will return repeated values, up until the point the sensor takes its next measurement. The automatic measurement mode can be used by Campbell Scientific dataloggers.
7.4.1 Measurements at the end of your Short Cut version does not include specific support for the CS215, the generic SDI12 Sensor instruction can be up to reset...
CS215 Temperature and Relative Humidity Probe - Page 19
... scan rate for the sensor to execute. With Campbell Scientific dataloggers this interval which allows table 1 to other measurements that use a control port rather than the SDI-12 port to allow the SDI12recorder instruction to run as the main scan. Using the aC! Using the aC! CS215 Temperature and Relative Humidity Probe
7.4.2 Measurements at Fast Scan...
CS215 Temperature and Relative Humidity Probe - Page 23
... 126.)
The factory-set SDI-12 address for the new address sent as most Campbell Scientific dataloggers (with the exception of the CR5000 at present) support a method of the window will turn green.
4. menu. In the Select Device menu, located in software by issuing the ?! If communications between 0 and 9. (The CS215 also supports the extended range...
CS215 Temperature and Relative Humidity Probe - Page 30
...:
• The element plugs into either side of socket but must be installed in one of the probe and sensor element. Identify the sensor element referring to the element.
24 Clean any dirt away using a damp ...directly to Figure 8-1 below, which shows a side-on the element.
5. CS215 Temperature and Relative Humidity Probe
8.1 Sensor Element Replacement
To replace the element:
1.
CS215 Temperature and Relative Humidity Probe - Page 36
... -30˚C In practical terms this means that is referenced to express relative humidity and is as defined by the sensor for instance, at temperatures below (although the electronics of the CS215 probe are not specified to prolonged periods of normal conditions or when subject to operate beyond +70°C). Normal operating conditions...
Campbell Scientific CS215 Reviews
Do you have an experience with the Campbell Scientific CS215 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Campbell Scientific yet.
Earn 750 points for your review!