IC Realtime IPEL-M80V-IRW1 Support and Manuals
Get Help and Manuals for this IC Realtime item
View All Support Options Below
Free IC Realtime IPEL-M80V-IRW1 manuals!
Problems with IC Realtime IPEL-M80V-IRW1?
Ask a Question
Free IC Realtime IPEL-M80V-IRW1 manuals!
Problems with IC Realtime IPEL-M80V-IRW1?
Ask a Question
Popular IC Realtime IPEL-M80V-IRW1 Manual Pages
Datasheet - Page 1
... the most challenging lighting conditions. IPEL-M80V-IRW1
4x2MP IR Dome Network Camera
&#...camera uses a set of up to...support for the first lens and 120dB for business intelligence, workforce optimization, and actionable intelligence. By adopting the latest technology, Cameras can replace...lightning rating provides effective protection for installation in dark environments. The Smart ...
Datasheet - Page 2
... 1920(H)x1080(V) 1024MB/128MB Progressive Auto/Manual, 1/3(4)~1/100000s 0.005Lux/F1.8( Color,1/3s,30IRE) 0.06Lux/1.8( Color,1/30s,30IRE) 0Lux/F1.8(IR on) More than 95% RH IP67 IK10
Metal 286.1mm×111.3mm 2.7kg (5.95lb) 3.6kg (7.94lb)
2 | www.icrealtime.com
FS-04012020-HV1-D1.01 IPEL-M80V-IRW1
Technical Specification
Camera
Image...
Product Manual - Page 2
... be deviation in technical data, functions and operations description, or errors in slight or moderate injury. You need to be in compliance with defined meaning might collect personal data of related
regions.
About the Guide
The Guide is inconsistency between paper manual and the electronic version, the electronic version shall prevail. All...
Product Manual - Page 3
...; Upgrade the reader software or try other mainstream reader software if the Guide (in PDF format) cannot be opened.
All trademarks, registered trademarks and the company names in the Guide are the properties of their respective owners.
Please visit our website, contact the supplier or customer service if there is any problem occurred...
Product Manual - Page 4
... the instructions in the Guide when performing...service for desiccant replacement if there is operating normally.
otherwise it might cause over brightness or light marks, which conforms to Limited power Source requirement according to IEC60950-1. Important Safeguards and Warnings
Electrical Safety
All installation and operation should conform to your local electrical safety codes...
Product Manual - Page 5
... damage on device body coating which could be removed with air
blower, or you need to upgrade the firmware or manually update the ONVIF password.
Use standard components or accessories provided by manufacturer and make sure the device is installed and maintained by professional engineers.
The surface of network, device data and personal information...
Product Manual - Page 6
... and receiver. ● Connect the equipment into an outlet on , the user is sold.
Regulatory Information
The regulatory information herein might vary according to the model you purchased. Regulatory Information V FCC conditions: This device complies with the instructions, may cause
undesired operation.
Product Manual - Page 8
... input and
1 I /O ports might vary on select models. For the detailed information about device ports, see Table ...manual. 1 Connecting Alarm Input/Output
Ports and Buttons
The following figures are for 10 s to reset the device to factory settings. Table 1-1 Port introduction
No.
For the detailed operation, see 0. Please be sure to supply power as instructed
in the Guide...
Product Manual - Page 9
...
Port Name Function ALARM_IN Receives the switch signal of the I /O port. Alarm outputs high and low level, and the alarm outlet
is available on select models. ALARM_GND Ground connection. Device collects different states of the I /O port. The default output signal switches to the alarm input end of external alarm source. Connecting...
Product Manual - Page 10
Log in web interface, and configure alarm input and alarm output in alarm setting. The alarm input in the web interface is corresponding to "NO" (default) if the alarm input ...will be high level and low level alarm signal generated by the alarm input device when alarm occurs, set the input mode to the alarm output end of the device, which is logic "0"; Connecting Alarm Input/Output 3
Product Manual - Page 11
... be finished with Status shows Uninitialized, and then click Initialize. See Figure 2-1.
Click . Modify IP
Click Search setting. For more information, see the WEB operation manual. Device initialization is available on select models, and it is required at first use or after the
device being reset. Device initialization is displayed. The...
Product Manual - Page 12
...; You can modify IP address of one or multiple devices in "2.1 Initializing Device" to be "wrong password" notice. After clicking Search setting, enter the username and password, and make sure they are the same as what you set during initialization, otherwise there will be modified, and then click Modify IP. The Initialization interface is...
Product Manual - Page 13
...Click Here to the same if you select DHCP. If the setup wizard is finished. Enter the user name and password in the log in Web Interface
Open IE browser, then ... the network, devices will be set to Download Plugin, and then install the plugin as instructed. The main interface is displayed when the installation is displayed, finish the settings as instructed. Logging in box, and then...
Product Manual - Page 14
... are contained in ])
Installation 7 Packing List
3 Installation
The tool required for the installation such as electric drill is not provided in the packing. The operation manual and related tool are for reference only, and the actual product shall prevail. Device dimension (mm [in the disk or the QR code, and the
actual packing...
Product Manual - Page 18
Cable going through the side cable tray
Installation 11
IC Realtime IPEL-M80V-IRW1 Reviews
We have not received any reviews for IC Realtime yet.