JET Tools JG-150A Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools JG-150A manuals!
Problems with JET Tools JG-150A?
Ask a Question
Free JET Tools JG-150A manuals!
Problems with JET Tools JG-150A?
Ask a Question
Popular JET Tools JG-150A Manual Pages
User Manual - Page 1
M-286575 Revision A2 04/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
3/4, 1-1/2, and 3 Ton Grip Pullers
Models JG-75A, JG-150A, JG-300A
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Model JG-75A shown
Part No.
User Manual - Page 2
... to parts, fittings, and accessory equipment which varies in your area call 1-800-274-6846 or use and are used for commercial or industrial purposes default to Get Technical Support Please contact Technical Service by a 90 day limited warranty against manufacturers' defects. Who is a division of our tools needs service or repair, please contact Technical Service by...
User Manual - Page 3
... owner's manual before each use if grip puller is damaged or malfunctioning. 15. Do not use as a tow line. 10. Do not wear loose clothing which can result in serious injury. 18. Do not use . Always inspect the puller before operating grip puller. Table of Contents
Warranty and Service ...2 Warning...3 Introduction ...4 Specifications ...4 Replacement Parts ...4 Unpacking...
User Manual - Page 4
... change specifications at our web site: www.jettools.com. This tool has been designed and constructed to provide years of trouble free operation if used in accordance with the grip puller, add a "K" to the end of your local supplier or JET.
This manual contains instructions on pages 8 through Friday (see our website for a JET Grip Puller. Replacement Parts
Replacement Parts are...
User Manual - Page 5
...sold and
packaged separately) 1 Owner's Manual 1 Warranty Card
Figure 1
FEATURES OF THE GRIP PULLER (1-1/2 ton model shown)
Assembly and Set-Up
Pre-Lubrication
Before proceeding with the following parts list to your distributor and shipping agent.
Unpacking
Open shipping container and check for assembly, maintenance and safety instructions. Missing parts, if any, should be reported...
User Manual - Page 6
...replaced... is too excessive for the puller's capacity, the shear pin is installed in the middle of higher pulling capacity. Lay out the wire rope...operate the grip puller:
1. To send the wire rope backward, set the telescopic handle on either the forward or reverse lever, according ...uses standard ASA wire rope and may be used in the parts list) is designed to provide easy entrance) into the ...
User Manual - Page 7
...lubrication. Oil the puller and wire rope.
Replace spring.
7 After use, remove the wire rope from the main body by setting the clamp lever into the notch (disengage the...allow it to return to both.
8. Spring on clamp lever has become stretched.
7.
Troubleshooting
Trouble
Probable Cause
Remedy
Wire rope will promote rusting.
Decrease load. Correct as needed. Puller...
User Manual - Page 8
JG-75A (3/4 Ton Grip Puller)
8
User Manual - Page 9
Part No. Parts List: JG-75A (3/4 Ton Grip Puller)
Index No.
Description
Size
Qty
1 JG75A-1 Case, Right 1 2 TS-2285121 Flat Head Screw M5x12 1 3...Assembly 1 25 JG75A-8 Shear Pin 1 26 JG75A-26 Axle...2 27 JG75A-27 Front Slide Assembly 1 28 JG75A-28 Spring Guide 2 29 JG75A-29 Spring...2 30 JG75A-30 Bottom Clamp 2 31 JG75A-31 Top Clamp 2 32 JG75A-32 Back Slide ...
User Manual - Page 10
JG-150A (1-1/2 Ton Grip Puller)
10
User Manual - Page 11
... JG150A-32 Hand Grip Assembly 1 33 JG150A-33 Rubber Handle Grip 1 34 JG150A-34 Cap ...2 35 JG150A-35 Clamp Plate, Short 4 36 JG150A-36 Clamp Plate, Long 4 37 JG150A-37 Retaining Ring 12 8 38 JG150A-38 Shaft ...4 39 JG150A-39 Swivel Hook 1 JG75A-WL Warning Label (not shown 1 286514 1-1/2T Wire Rope, 66 Ft. (not shown 1
11 Parts List: JG-150A...
User Manual - Page 12
JG-300A (3 Ton Grip Puller)
12
User Manual - Page 13
Parts List: JG-300A (3 Ton Grip Puller)
Index No. Part No.
Description
Size
Qty
1 JG300A-1 Case, Right 1 2 JG300A-2 Flat Head Screw M5x8 1 3 JG75A-3 Washer 1 4 JG300A-4 Case, Left 1 5 JG300A-5 Name Plate 1 6 JG75A-6 Rivet M2x6 4 7 JG300A-7 Fastening Bolt Assembly 1 8 JG300A-8 Shear Pin 5 9 JG150A-9 Telescopic Handle 1 10 TS-1551061 Lock Washer M8 6 11 TS-...
JET Tools JG-150A Reviews
We have not received any reviews for JET Tools yet.