JET Tools WH-45T Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools WH-45T manuals!
Problems with JET Tools WH-45T?
Ask a Question
Free JET Tools WH-45T manuals!
Problems with JET Tools WH-45T?
Ask a Question
Popular JET Tools WH-45T Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
45-inch English Wheel
Model: WH-45T
JET 427 New Sanford Road LaVergne, Tennessee 30786 Ph.: 800-274-6848 www.jettools.com
Part No. M-756151 Revision A1 05/2014 Copyright © 2014 JET
User Manual - Page 2
....
Parts; Electric Hoists, Electric Hoist Accessories 5 Year - VOLT Series Electric Hoists; References in this document to JET also apply to the JET brand.
2
JET has Authorized Service Centers located throughout the United States.
For complete, up-to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or lack of our tools needs service...
User Manual - Page 3
... ...6 Specifications ...6 Unpacking and Setup ...7
Cleanup ...7 Site Considerations ...7 Moving the English Wheel...7 Securing to Floor...7 Operation ...7 Overview...7 Basic Operations...8 Adjustments ...8 Replacing the Wheel ...8 Rotating Wheels...9 Rolling Tips...10 Adjusting the Quick Release Lever...10 Wheel Alignment...10 Lubrication...11 Troubleshooting the WH-45T English Wheel 12 Parts...
User Manual - Page 4
...manual before use .
6. Failure to comply with the proper and safe operation of drugs, alcohol or any other purposes, JET...If possible, the English Wheel should be properly repaired or replaced.
14. Make your workshop child proof with...Replace warning labels if they are specifically designed to determine that is designed and intended for alignment of moving parts, binding of moving parts...
User Manual - Page 5
... occur if the machine tips over.
25.
Maintain tools with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in serious injury or possibly
5 Use the right tool at the correct feed rate. The right tool will do a job for lubricating and changing accessories...
User Manual - Page 6
... in accordance with instructions set forth in this manual before attempting assembly or operation. Failure to change specifications at our web site: www.jettools.com.
If there are any time and without prior notice, without incurring obligations. Introduction
This manual is provided by JET, covering the safe operation and maintenance procedures for the JET WH-45T English Wheel. This...
User Manual - Page 7
...WH-45T is rolled between the upper wheel and lower wheel, it becomes longer and thinner. Securing to Floor
Mounting the machine to support both machine and operator. Some parts... and footprint specifications for anchoring to a concrete floor. Retractable wheels beneath the main column and support legs allow ...Setup
Cleanup
Exposed metal surfaces, including upper and lower wheels, are recommended ...
User Manual - Page 8
...to Figure 2:
2. Hold upper wheel securely when installing or removing. To replace an upper wheel:
Refer to decrease pressure. Basic... and top of the lower wheel (E). Adjustments
Replacing the Wheel
The JET English Wheel is supported.
8
Figure 2
Refer to raise or lower...upper wheel bracket (B) against the bottom of this manual. Wear steel-toed footwear for personal safety. Place the ...
User Manual - Page 9
...to the operating position.
Note: Adjust the lower wheel height if you need more clearance replacing the upper wheel. Disengage the quick release lever (F, Figure 4) and lower the lower...
Align the wheel bearing holes with another one.
3. Carefully remove the upper wheel (D) and set it is currently positioned (L1).
Lift the lower wheel assembly until there's sufficient clearance.
2....
User Manual - Page 10
... wheel 90 degrees (D), then raise the upper wheel bracket (B) until it may have become loose during shipping. However, it is seated against the frame.
9. The set screws must engage the lever to lower the upper wheel bracket (B) below the frame block (C).
8. Figure 7
Rolling Tips
Observe the following steps.
7. Use a hex wrench...
User Manual - Page 12
...Parts
Ordering Replacement Parts
To order parts or reach our service department, call will allow us to serve you call 1-800-274-6848 Monday through Friday (see our website for business hours, www.jettools.com). Having the Model... too low a crown
Lower wheel flat is too small. Troubleshooting the WH-45T English Wheel
Trouble
Quick release lever will not seat frame block;
Upper wheel swivels...
User Manual - Page 14
...TS-1522031 Socket Set Screw M5x10 2 38 TS-1522041 Socket Set Screw M5x12 ... 31) .....3/4 1 22 WH45-22 Lower Wheel 8 1 23A .......... Parts List for WH-45T English Wheel
Index No.
WH45-21A Lower Wheel 6 Assembly (Index #...3 1 25A .......... Description
Size
Qty
1 WH45T-1 Frame...1 1-1 WH45T-1-1 Post Clamp 2 1-2 WH45T-1-2 Frame Support Stand 1 2 WH45-2 Collar ...1 3 ...
User Manual - Page 15
... usually be purchased as an assembly. Parts List for WH-45T English Wheel
Index No. Part No. are standard fasteners and can only be found at local hardware stores.
15 Description
Size
Qty
41 WH45-41 Snap Ring 20 1 42 TS-1522031 Socket Set Screw M5x10 1 46 TS-1523021 Socket Set Screw M6x8 1 47 TS-1503071...
User Manual - Page 16
...800-274-6848 www.jettools.com
16 For example, when ordering Lower Wheel 1 (Index 18), order Part Number WH45-18A (Index 18A) from the column to the left of the wheel and use that... includes the wheel, ball bearings and shaft (lower wheel only). in the Parts List (preceding pages). Wheel 25
Description
Spec
Lower wheel 2 1-29/64"
19
Lower wheel 9 1/2" Ridged
26...
JET Tools WH-45T Reviews
We have not received any reviews for JET Tools yet.