Lowrance NAC-3 Autopilot Computer Support and Manuals
Get Help and Manuals for this Lowrance item
View All Support Options Below
Free Lowrance NAC-3 Autopilot Computer manuals!
Problems with Lowrance NAC-3 Autopilot Computer?
Ask a Question
Free Lowrance NAC-3 Autopilot Computer manuals!
Problems with Lowrance NAC-3 Autopilot Computer?
Ask a Question
Popular Lowrance NAC-3 Autopilot Computer Manual Pages
Addendum software release v20.2 for Zeus2 Glass Helm - Page 15
... select to show all ranges (based on radar range) or targets within a specific distance of targets exceeds the set number, only the most dangerous targets on top. If the amount of own...Ú Note: True bearing can only be selected when a compass is to hide targets that support tracking targets, the following distance will be shown. specify to show radar targets on top and ...
Addendum software release v20.2 for Zeus2 Glass Helm - Page 16
.... You can be displayed and tracked.
Installation The Installation option is connected to set in the separate Radar or the display unit's installation manuals.
It is the total length of the... can be selected at a time.
16
ADDENDUM | Zeus Series New antenna setup option The Antenna setup option is an important tool for DSC transmitting devices within range. AIS vessels...
Addendum software release v20.2 for Zeus2 Glass Helm - Page 21
... radars that support target tracking, the following distance will also apply to specify:
• Dangerous targets - ADDENDUM | Zeus Series
21 Extension lines Defines the length of interest -
By default, all targets are only available if you have your MMSI number entered to avoid seeing your system.
Ú Note: For radar specific settings, refer...
Network Autopilot Installation and Commissioning Manual - Page 71
... 24 CHECKING THE COMPASS OFFSET 25 AUTOMATIC RUDDER GAIN 25
CHECKING THE AUTOMATIC RUDDER GAIN LEARNING __________ 26 MANUAL RUDDER GAIN 26 SETTING THE RUDDER GAIN MANUALLY 27
RUDDER GAIN VALUE TABLE 28 BOAT LAG 28 SETTING THE BOAT LAG VALUE 29
BOAT LAG VALUE TABLE 29 CALIBRATION OF DIRECT SPEED INPUT 30 POWER...
Zeus Touch Install Manual - Page 30
...another Zeus Touch unit via the network. Access the Video Menu by adjusting the video image settings (brightness, saturation, etc.). Connecting video sources
VIDEO IN
RED GREEN
VIDEO 1
...configuration
Tapping the video panel will not be shared with T12). Video In | Zeus Touch installation manual
You can optimize the video display by one of the display.
Note: The...
Zeus Touch Install Manual - Page 44
... results. If another model compass from B&G or another manufacturer is installed, refer to the instruction for that compass regarding calibration. Note: In certain areas and at which you want to change the set of steering
parameters) • Automatic tuning of the steering parameters
• Setting the seastate filer • Saiboat setup
Compass calibration Before the...
Zeus Touch Install Manual - Page 45
... the system automatically changes from LO to HI steering parameters. LO response
HI response
Transition to LO parameters with increasing speed: 10kn
Transition speed set manually
Autopilot | Zeus Touch installation manual | 45 LUBBER LINE
Magnitude of local field in % of local field with respect to lubber line. Steer the boat so that the center line...
Network Pilot Installation Manual ACP - Page 50
... design and testing to ensure compliance with the instructions as possible to reduce the possibility of this equipment. Specific attention is installed and operated in accordance with the European EMC ...and cables are used unmodified. Transmissions from poorly installed or maintained Single Sideband equipment may vary according to model and are shown in detail on the connection diagrams...
Network Pilot Installation Manual ACP - Page 71
... 24 CHECKING THE COMPASS OFFSET 25 AUTOMATIC RUDDER GAIN 25
CHECKING THE AUTOMATIC RUDDER GAIN LEARNING __________ 26 MANUAL RUDDER GAIN 26 SETTING THE RUDDER GAIN MANUALLY 27
RUDDER GAIN VALUE TABLE 28 BOAT LAG 28 SETTING THE BOAT LAG VALUE 29
BOAT LAG VALUE TABLE 29 CALIBRATION OF DIRECT SPEED INPUT 30 POWER...
Zeus Glass Helm Installation Manual - Page 47
... socket)
NMEA 0183 port baud rate 4800, 9600, 19200, & 38400 (via proprietary cable)
RS422 port baud rate Charting support
1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 Embedded low detail backround +
Insight, Navionics and CMap on ...are PoE (RJ45 socket) 1 port on rear (Micro-C male, LEN = 1)
Video input
2 ports on SD card
Specifications | Zeus2 Glass Helm Installation Manual
| 45
NAIS 400 Owners Manual - Page 27
... to receive your AIS transceiver. Specific details of how to configure your chartplotter to make use the full range of other vessels will be given in Figure 13.
Warning: When silent mode is ready for your chartplotter or PC. Follow the instructions provided in Step 4 and 5 under Installation procedures, chapter 3, an external switch...
NSPL 400 User Manual - Page 2
... as follows: ¼¼ Note: Used to specifications without notice.
The user of the Documentation, the English language version will not cause accidents, personal injury or property damage.
Governing Language: This statement, any instruction manuals, user guides and other important information. In the event of the manual. Copyright Copyright © 2012 Navico Holding AS. Please...
H2000 User Manual - Page 94
...the wind at the mast head and the wind at ground level and the wind aloft; h2000 User Manual
CAL VAL 2 Setting 0
1
Description
Default setting.
The change in an early sea-breeze, but as moving air comes into contact with the ground... WIND SPEED AND ANGLE
3.3.1 Principles of Wind Speed/Angle Calibration
One of the greatest problems for an instrument system to the main processor.
H2000 User Manual - Page 114
...calibration value is required. If the sensor is a totally independent fitting (B&G part no. 224-00-065) then it is necessary to calibrate this case... temperature. The paddle-wheel has a sensor incorporated within it, in exceptional circumstances or after a system reset.
h2000 User Manual
CAL VAL 2 Setting 0 1 2 3 4 5
Function Text Shown
AFT DPTH FWD DPTH MID DPTH PORT DEP STBD DEP DEPTH 2
...
Network Quad User Manual - Page 20
...- 590 ft, 0 - 98.4 fa.
610-HB-0503-05
20 Silence the alarm by pressing any key. Anchor Alarm • Factory set to 1.0m, (3.2ft, 0.5 fathoms). • Adjustable range 0 - 180m, 0 - 590ft, 0 - 98.4 fa.
The alarm information...TACK which do not have alarms. See NETWORK ALARMS at the end of this manual.
DEPTH ALARMS
The display will sound its' internal alarm buzzer and flash DEPTH ...
Lowrance NAC-3 Autopilot Computer Reviews
We have not received any reviews for Lowrance yet.