Makita XAG03Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XAG03Z manuals!
Problems with Makita XAG03Z?
Ask a Question
Free Makita XAG03Z manuals!
Problems with Makita XAG03Z?
Ask a Question
Popular Makita XAG03Z Manual Pages
XAG03Z Instruction Manual - Page 1
INSTRUCTION MANUAL
Cordless Angle Grinder
XAG03 XAG04
IMPORTANT: Read Before Using. 1
015078
XAG03Z Instruction Manual - Page 2
...specifications herein are subject to follow the warnings and instructions may differ from heat, oil, sharp edges or moving parts...-operated (corded) power tool or battery-operated (cordless) power tool. Work area safety 1. Never use... work area clean and well lit. ENGLISH (Original instructions)
SPECIFICATIONS
Model
XAG03
XAG04
Wheel diameter
115 mm (4-1/2")
125 mm (5")
Max...
XAG03Z Instruction Manual - Page 3
...repair person using only identical replacement parts. Under abusive conditions, liquid may be ejected from the power tool before making any adjusting key or wrench before use and care 24. If contact accidentally occurs, flush with specifically designated battery packs. GEB059-3
CORDLESS GRINDER...repaired. 19.
Use of fire when used . Follow instruction for your power tool serviced...
XAG03Z Instruction Manual - Page 4
...pulling the accessory into the surface of the accessory must match the grinder spindle thread. Accidental contact with a "live " and could ignite... hardware of the power tool will also make exposed metal parts of snagging. As appropriate, wear dust mask, hearing protectors... power tool at maximum no-load speed for damage or install an undamaged accessory. Do not use inspect the accessory such...
XAG03Z Instruction Manual - Page 5
... the wheel, at you. Supports must be mounted below the plane...Specific for maximum safety, so the least amount of a guard is binding or when interrupting a cut . c) When wheel is recommended for which the power tool was not designed cannot be adequately protected. f) Use extra caution when making a "pocket cut . This grinder is not designed for these parts could indicate poor installation...
XAG03Z Instruction Manual - Page 6
...instructions...INSTRUCTIONS. Do not incinerate the battery cartridge even if it for this
instruction manual... may be subjected to safety rules for tool. ･ volts
･ direct current
･ rated speed
･ no load speed
･ revolutions or reciprocation per minute
IMPORTANT SAFETY INSTRUCTIONS... use ) replace strict adherence
... INSTRUCTIONS...instructions...
XAG03Z Instruction Manual - Page 8
...on the position of the following conditions. To release the protection lock, remove the battery, set it to become overloaded.
Shaft lock
CAUTION: • Never actuate the shaft lock when ...ASSEMBLY
CAUTION: • Always be sure that causes it to prevent spindle rotation when installing or removing accessories. Automatic speed change function
1.
In this situation, the tool does not...
XAG03Z Instruction Manual - Page 10
... on a grinder frequently kick and..., follow the installation procedure in this manual.
The
weight ...of about 15 degrees to a complete stop before putting the tool down.
10 CAUTION: • Never switch on the side handle.
Forcing and excessive pressure could cause dangerous wheel breakage. • ALWAYS replace...wheel or disc at an
angle of the tool applies adequate...
XAG03Z Instruction Manual - Page 12
...clean it upside down allowing easy access to be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
12 MAINTENANCE
CAUTION: • Always be sure that ... tool and its air vents have to spindle. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be kept clean. Remove any accessories on spindle...
XAG03Z Instruction Manual - Page 13
... Makita tool specified in this manual. Your failure to do so could result in personal injury to you need any other accessories or attachments might present a risk of injury to persons. If you and others. If you decide to use your Makita grinder with approved accessories which you purchase from your local Makita Service Center. • Makita...
XAG03Z Instruction Manual - Page 14
1
2
6
2
10
11
3
7
9
3
4
8
12
5 5
115 mm (4-1/2") model
125 mm (5") model
1
Grip 36
2
Wheel Guard (for grinding wheel)
3
Inner flange 45
Inner flange 45
4
Depressed center wheel/Multi-disc
5
Lock nut 5/8-45
Lock nut 5/8-45
6
Rubber ...
XAG03Z Instruction Manual - Page 15
...FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY.
It is warranted to one of Makita's Factory or Authorized Service Centers. IN NO EVENT SHALL MAKITA BE LIABLE FOR ... specific legal rights, and you may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. If inspection shows the trouble ...
XAG03Z Parts Breakdown - Page 2
...45 XAG03 NAME PLATE TAPPING SCREW 4X18 DUST COVER R MOTOR H0USING SET ...SET RUBBER PIN 6 INC. 33 DUST COVER L TERMINAL RESISTOR UNIT LEAD UNIT
1 PC. 1 PC. 1 0 1 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 4 PC. 1 PC. 1 PC. 1 1 PC. 1 PC. 1 PC. 1 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 4 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 5 PC. 1 1 2 PC. 0 1 1 1 1 1 1 1 PC. 1 2 PC. 0 1 1 PC. 1 PC. 1 PC. Model XAG03Z Parts...
Makita XAG03M New Tool Flyer English - Page 1
... level
ERGONOMICS
14-1/4" Long
Compact and ergonomic design at only 14-1/4" long
CORDED GRINDING PERFORMANCE
makitatools.com 18V LXT® Lithium-Ion Brushless Cordless 4-1/2" Cut-Off/Angle Grinder Kit
Model XAG03M/Z
AUTOMATICSPEEDCHANGE™TECHNOLOGYADJUSTSSPEEDANDTORQUE DURINGOPERATIONFOROPTIMUM PERFORMANCE
• BL™BrushlessMotor delivers8,500RPM
• TheBL™BrushlessMotor...
Makita XAG03M New Tool Flyer English - Page 2
... comfort on battery
SPECIFICATIONS
Grinding Wheel or Cut-O ff Wheel
4-1/2"
Wire cup brush No Load Speed
3-1/2" 8,500 RPM
Model XAG03M
Model XAG03Z
Battery 18V LXT® Lithium-Ion 4.0 Ah
Overall Length 14-1/4"
Net Weight Shipping Weight
5.5 lbs. (w/battery) 18 lbs.
0 88381 68922 9
0 88381 68459 0
UPC Code XAG03M UPC Code XAG03Z
STANDARDEQUIPMENT
088381-689229...
Makita XAG03Z Reviews
We have not received any reviews for Makita yet.