Makita XSH08Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XSH08Z manuals!
Problems with Makita XSH08Z?
Ask a Question
Free Makita XSH08Z manuals!
Problems with Makita XSH08Z?
Ask a Question
Popular Makita XSH08Z Manual Pages
XSH08 Instruction Manual - Page 2
...to country.
• The weight may differ from heat, oil, sharp edges or moving parts. WARNING: Only use a ground fault circuit interrupter (GFCI) protected supply.
Keep children and... and well lit. Keep cord away from country to lose control. ENGLISH (Original instructions)
SPECIFICATIONS
Model:
XSH08
Blade diameter
185mm (7-1/4")
Max. Do not use the cord for advice before...
XSH08 Instruction Manual - Page 5
...the lower guard may be retracted manually only for and remove all other... fall off . 4.
With appropriate Makita genuine circular saw , especially when ..., they must be serviced before making cross-cuts...the workpiece is solidly supported, not on that...part of the saw base on the section that can also be sure that the lower guard is released.
5. Unsharpened or improperly set...
XSH08 Instruction Manual - Page 6
... may result in a risk of electrolyte. A battery short can lead to follow the safety rules stated in this instruction manual may result in loss of non-genuine Makita batteries, or batteries that
is required. Installing the batteries to water or rain. Keep blade sharp and clean.
Symbols
The followings show the symbols used for...
XSH08 Instruction Manual - Page 7
... charged battery cartridge. Let a hot battery cartridge cool down the base when installing/removing the batteries.
Installing or removing battery cartridge
CAUTION: Always switch off the tool before ... that causes it is placed under one battery cartridge. Overcharging shortens the battery service life.
3. Charge the battery cartridge if you . FUNCTIONAL DESCRIPTION
CAUTION: Always...
XSH08 Instruction Manual - Page 8
...indicator lamps light up for proper repairs BEFORE further usage. The battery indicators correspond to stop.
1 2 1
2
► 1 . A switch with the indicator
0% to a Makita service center for a few seconds....the battery cartridge to indicate the remaining battery capacity.
Switch action
WARNING: Before installing the battery cartridge into the tool, always check to see that the switch...
XSH08 Instruction Manual - Page 9
... tighten the clamping screws
securely.
► 1 . For cleaner, safer cuts, set cut depth helps to reduce potential for quicker cutting operation. Set for powerful cutting operation.
► 1 . The tool automatically changes the operation mode depending on the depth guide and move the base up in green when the tool is operated with excessive load...
XSH08 Instruction Manual - Page 10
...saw blade after releasing the switch trigger.
► 1 . CAUTION: Never hook the tool at a Makita service center. CAUTION: The blade brake system is hooked.
► 1 . Cutting line (45° ... RESULT.
10 ENGLISH Sighting
For straight cuts, align the 0° position on the front of the base with the screws as illustrated.
1 ► 1 .
Lamp
NOTE: Use a dry cloth to ...
XSH08 Instruction Manual - Page 12
... guard is retracted above the base without the ring
1
2
Connecting a vacuum cleaner
5
When you intend to the dust nozzle as discussed in the Maintenance section. Inner flange 3. Ring
WARNING: BE SURE TO TIGHTEN THE HEX BOLT CLOCKWISE SECURELY. Such efforts do not replace the need to your local Makita dealer for the material...
XSH08 Instruction Manual - Page 13
... to avoid positioning which exposes operator to its full capacity. Rip fence (Guide rule) 2. Hold the tool firmly. Set the base on the rear end of the workpiece and secure it flat and
advancing smoothly... to turn the tool on the tool base so that the rip fence is low, the tool may not work to properly follow your tool serviced at a Makita service center. Simply slide the rip fence up...
XSH08 Instruction Manual - Page 14
... warnings specific for lanyard (tether strap)
MAINTENANCE
CAUTION: Always be performed by the attachment device or the lanyard.
11. Always keep the tool tethered when working area so that it engages the undercut groove in contact with compressed air. Do not carry the tool by Makita Authorized or Factory Service Centers, always using Makita replacement parts...
XSH08 Instruction Manual - Page 15
... by turning the adjusting screw with your local Makita Service Center. • Circular saw blade may bite into the guide rail and the damaged guide rail may differ from country to check the ... the base so that the bevel angle can also use with a hex wrench. Loosen the screws shown in this manual. Adjusting screw for more details regarding these accessories, ask your Makita tool ...
XSH08 Instruction Manual - Page 16
United States of America: www.makitatools.com Canada: www.makita.ca Other countries: www.makita.com
16 ENGLISH If annexed warranty sheet is not available, refer to this product. MAKITA LIMITED WARRANTY
Please refer to the annexed warranty sheet for the most current warranty terms applicable to the warranty details set forth at below website for your respective country.
XSH08 Parts Breakdown - Page 2
...1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. Model XSH08Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
266326-2
002
458750-5
006
855P90-2
007
266326-2
008
183K66-2
008 C10 263005-3
008 C20 ...211031-6
TAPPING SCREW 4X18 FRONT GRIP XSH08 NAME PLATE TAPPING SCREW 4X18 HANDLE SET RUBBER PIN 6 CAUTION LABEL INC. 20 INDICATION...
XSH08 Parts Breakdown - Page 3
...(EXT) WR-40 INNER FLANGE 35 OUTER FLANGE 35 HEX. BOLT M8X20 DEPTH GUIDE CAP SQUARE NECK BOLT M6X30 + PAN HEAD SCREW M5 FRAME PAN HEAD SCREW ...SPRING 3.5 SHOULDER PIN 3-5 THUMB SCREW M4X3 HOLDER SLIDE LEVER WAVE WASHER 10 PLATE THUMB SCREW M6X14 COMPRESSION SPRING 8 THUMB SCREW M4X3 HOLDER + TRUSS HEAD SCREW M4X16 BASE H.S.SET SCREW(FLAT POINT)M6X8 LOCK WASHER COUNTERSUNK HEAD SCREW M4X10
1 PC. 1 PC...
XSH08PT New Tool Flyers English - Page 1
... eliminates carbon brushes, enabling the BL™ Motor to run time without prior notice. 18V X2 LXT® LITHIUM-ION (36V) BRUSHLESS CORDLESS 7-1/4" CIRCULAR SAW KIT WITH GUIDE RAIL COMPATIBLE BASE (5.0AH)
NEW TOOL OVERVIEW
XSH08PT
ALSO AVAILABLE AS A BARE TOOL: XSH08Z
PRODUCT HIGHLIGHTS
DESIGN
0°- 48° bevel capacity with a positive stop at 45°...
Makita XSH08Z Reviews
We have not received any reviews for Makita yet.