Stihl FG 3 Support and Manuals
Get Help and Manuals for this Stihl item
Popular Stihl FG 3 Manual Pages
Instruction Manual - Page 2
...STIHL product. K1.
Printed on correct procedure in Germany
12
FG 3 T. english
Guide to the illustration and contains item numbers that require your satisfaction and troublefree use of the power tool. Description of step or procedure that refers directly to Using this manual... order to avoid damage to the operating instructions, this Manual
Dear Customer, Thank you have any queries...
Instruction Manual - Page 3
... model on the saw. and in a safe place for assistance.
The file only sharpens on the backstroke.
- Components that are set too low -
Always shut off the cutter on the forward stroke -
For accurate results it is incorrectly sharpened - FG 3
13
Electric saws: Disconnect plug from those described in these instructions. If the saw . The STIHL filing tool...
Instruction Manual - Page 4
... KN
566BA004 KN
english
Setting Up
1 1 2
: Place the filing tool on the guide bar.
4
3
: The clamping jaws (1) must point to the left -hand row of cutters, clamp the guide bar so that the chain...(2). If the master cutter is the master cutter for filing all other cutters.
Use a slide caliper or similar to center the filing tool above the chain.
: Tighten the second clamping jaw with...
Instruction Manual - Page 5
...)
4,0
(5/32)
4,8
(3/16)
5,2
(13/64)
5,5
(7/32)
1 = Set the filing angle
One notch on clamp is equivalent to 5°.
566BA005 KN 566BA006 KN
english
2
3
3
: Fit the specified chain sharpening file (2) in the two holders on the filing tool and secure in positon with the screws (3).
Use only special saw chain sharpening files.
Other files are unsuitable for sharpening chains...
Instruction Manual - Page 6
... of master cutter (4) so that it is approximately under the center of the stop roller (5).
6
: Rotate height adjusting screw (7) (counterclockwise to raise file) until 1/10 of
file diameter projects above top plate.
566BA008 KN
: Position the file (6) between the side plate and depth gauge of the master cutter by swinging and lifting the...
Instruction Manual - Page 7
... the
cutter to be sharpened.
: Now rotate the knurled nut a little more until the side plate presses against the file and the stop bar (10) is not the case, readjust the stop again. FG 3
17
Sharpening
english
10 4 9
8
12
3
10 4
12
566BA010 KN 566BA011 KN
: Rotate the knurled nut (8) to move stop...
Instruction Manual - Page 8
... cutters in the first row, reset the filing tool to sharpen the second row as described in chapter "Adjustments". A
After sharpening the first cutter in the second row: : Check the cutter length (A).
3
: If it
has to be lowered.
18
FG 3
566BA014 KN
english
Use the setting for the master cutter to sharpen all cutters...
Instruction Manual - Page 9
FG 3
english 19
a
566BA017 KN
: Finish off by filing the slope by hand, parallel to the stamped marking, until it butts against the back of the cutter.
: Rotate height adjusting screw (4) so that the depth gauge is approx.
0.5 mm.
Then remove the filing gauge and file down all depth gauges to the same setting. 4
2 3
566BA016 KN...
Instruction Manual - Page 10
english
Main Parts
1
2
3
4 5
10 6
7
1 Guide 2 Height adjusting screw 3 Lateral adjusting screw 4 Stop bar 5 Sharpening file 6 Adjusting screw 7 Wing screw 8 Stop 9 Clamp screw 10 Clamping jaws
20
8 9 10
566BA001 KN
FG 3
Stihl FG 3 Reviews
We have not received any reviews for Stihl yet.