Stihl TS 400 Support and Manuals
Get Help and Manuals for this Stihl item
View All Support Options Below
Free Stihl TS 400 manuals!
Problems with Stihl TS 400?
Ask a Question
Free Stihl TS 400 manuals!
Problems with Stihl TS 400?
Ask a Question
Stihl TS 400 Videos
STIHL TS 400
Duration: 2:41
Total Views: 73,931
Duration: 2:41
Total Views: 73,931
stihl ts 400 concrete saw throttle assembly repair
Duration: 5:46
Total Views: 1,681
Duration: 5:46
Total Views: 1,681
?????????? Stihl TS 400
Duration: 2:07
Total Views: 19,440
Duration: 2:07
Total Views: 19,440
Stihl TS 400 TS400 Concrete Metal Cutting Saw (SOLD) on E-Bay For $400
Duration: 2:19
Total Views: 44,514
Duration: 2:19
Total Views: 44,514
Popular Stihl TS 400 Manual Pages
Instruction Manual - Page 2
...off machine cart 42 Storing the machine 42 Maintenance chart 43 Parts and Control 44 Specifications 46 Special Accessories 47 Maintenance and Repairs 47 STIHL Incorporated Federal Emission Control 2007Warranty Statement 48 Trademarks 50
STIHl
TS 400
English / USA
Allow only persons who understand this manual.
!Warning! Because a cut -off machine. Careless or improper use may cause...
Instruction Manual - Page 3
... that are not installed on correct procedure in order to avoid damage to the operating instructions, this manual.
2
TS 400 Such paragraphs are marked with the symbols described below:
Warning where there is to property. Engineering improvements
STIHL's philosophy is a risk of an accident or personal injury or serious damage to continually improve all models and related...
Instruction Manual - Page 4
...STIHL dealer show you how to operate your cut -off machine.
the use of the cut -off machine.
if you have different parts and controls. If you get tired while operating your cut -off machine. TS 400
3
Read the instruction manual...lend or rent your model cut -off machine without the instruction manual. Employers should not be in this manual.
Bystanders, especially ...
Instruction Manual - Page 5
... created by the engine to protect your hands warm.
- Do not wear shorts.
4
TS 400 These conditions reduce the hand's ability to have higher vibration levels.
- Take frequent breaks....medical advice immediately.
!Warning! If any obstacles or moving parts of whitefinger disease. Most STIHL cut -off machine models are mentioned as high vibration levels and long periods of exposure...
Instruction Manual - Page 6
... not utilized, the operator should have their use with the specific STIHL cut -off machine, see information under "Working Conditions" in cut -off machine noise may be extremely dangerous. For additional details and warnings on this instruction manual. Never modify a cut to your head. TS 400
5 When cutting metal, a cut -off machine generates sparks that burns...
Instruction Manual - Page 7
...:
6
TS 400 Clean dust from blade contact, thrown objects and/or reactive forces, including kickback. Abrasive wheels are different abrasive wheels, each specially marked. See section on the powerhead, especially around the carburetor, and may cause the wheel to the spindle speed of any addional safety precautions that is cracked or warped. Your STIHL...
Instruction Manual - Page 9
... properly mounted, and the wheel guard is running.
8
TS 400
Always shut off machine, be carefully inspected for fuel (see the chapter on "Fuel" of your instruction manual).
!Warning! Gasoline vapor pressure may shatter during operation and cause serious personal injury. In order to avoid an incorrect setting, the tensioning procedure must be followed as to allow...
Instruction Manual - Page 18
... storing for maintenance and repair. Store cut -off machine.
TS 400
17
in the USA, Canada and Australia), never operate your owner's manual.
! Store wheels on the machine.
Avoid direct skin contact and do not inhale the gas vapors. English / USA
Maintenance, Repair and Storing of the Cut-Off Machine
Maintenance, replacement, or repair of the emission...
Instruction Manual - Page 19
... is generally not suitable for dust suppression. - Wet cutting can reduce the energy of this manual.
Wet cutting is not at least 0.6 liters water per minute. Must be protected against vibration... is the part? - Must be fully supported - The last cut . It increases the service life and cutting speed of diamond cutting wheels Ensure that has been cut off or out.
18
TS 400 In a ...
Instruction Manual - Page 38
... operation.
* see "Guide to form on at cold ambient temp.):
: Turn the low speed adjusting screw (L) counterclockwise -
at idle speed
: Set to the low speed adjusting screw (L). Abrasive wheel runs on the insulator nose which may result in trouble in the same direction. These factors cause deposits to Using this Manual"
TS 400
37 until the...
Instruction Manual - Page 39
... TR 338BA027
38
TS 400 see "Specifications". : Use only resistor type spark plugs of spark plug: : Too much oil in the boot may create arcing that could ignite combustible fumes and cause a fire.
English / USA
If engine is down on power, difficult to start or runs poorly at part load. Rectify problems which have caused...
Instruction Manual - Page 44
... Using this Manual"
TS 400
Before starting work After work or daily Every time after about 100 operating hours
Accessible nuts and bolts (but not adjusting screws)
Retighten
Check
X
Rubber buffer (AV element)
Have replaced by servicing dealer 1)
Cutting wheel
Check Replace
X
X
Support / bracket / rubber buffer Check
X
(bottom side of leaks) X
X
Clean
X
Parts
Functional test...
Instruction Manual - Page 48
... if the repair has been performed by authorized STIHL service shops. TS 400
47 Original STlHL parts can be identified by the STlHL part number, the STIHl logo and, in some cases, by the STlHL parts symbol (.
... out only the maintenance operations described in this manual. This symbol may be performed only by an authorized STIHL servicing dealer using original STIHL replacement parts.
Instruction Manual - Page 49
... pleased to explain the Emission Control System Warranty on your failure to STIHL.
48
TS 400
Box 2015, Virginia Beach, VA 23450-2015. Warranty Period
The warranty period will be designed, built and equipped, at an authorized dealer), parts, and labor.
STIHL Incorporated must be repaired or replaced by the initial purchaser and you have any emissionrelated...
Instruction Manual - Page 50
... to the determination that part.
Maintenance Requirements
The maintenance instructions in writing by the failure of the emission test. Warranty Work
STIHL Incorporated shall remedy warranty defects at an authorized STIHL servicing dealer. TS 400
49 Diagnosis
You, as required maintenance will be used for that a warranted part is scheduled for replacement as the owner, shall...
Stihl TS 400 Reviews
We have not received any reviews for Stihl yet.