ZyXEL MS-7206 and Modules Support and Manuals
Get Help and Manuals for this ZyXEL item
This item is in your list!
View All Support Options Below
Free ZyXEL MS-7206 and Modules manuals!
Problems with ZyXEL MS-7206 and Modules?
Ask a Question
Free ZyXEL MS-7206 and Modules manuals!
Problems with ZyXEL MS-7206 and Modules?
Ask a Question
Popular ZyXEL MS-7206 and Modules Manual Pages
User Guide - Page 4
... ready when you contact an office.
• Product model and serial number. • Warranty Information. • Date that cannot be here.
If you cannot contact your vendor. Brief description of answers to solve it.
4
MS-7206 User's Guide
About This User's Guide
Need More Help? Customer Support
Should problems arise that you received your product, the answer...
User Guide - Page 33
... interface modules in slot 1, it automatically becomes the active management card.
In the MS-7206 system, the MAC address comes from the active management card when the MS-7206 system starts up again.
You can install management cards in slot 1 or slot 2.
3.1.1 Add a Management Card (System Is Off)
1 Insert the card in a different MS-7206 system because it in the MS-7206 chassis...
User Guide - Page 34
... of the existing management card, the new management card does not function in the MS-7206 chassis.
If you want to hot-swap interface modules, follow these steps.
34
MS-7206 User's Guide You do not have to configure the Slot Setup screen.
3.2.2 Add an Interface Module (System Is On)
If the same type of interface module was previously installed in the slot...
User Guide - Page 36
Figure 6 Slot Setup (Install)
3.2.3 Remove an Interface Module
Remove the interface module from the MS-7206 chassis.
36
MS-7206 User's Guide
Chapter 3 Installing Cards
4 Open the Slot Setup screen, and install the new type of interface module in the slot.
User Guide - Page 77
Figure 23 Slot Setup
MS-7206 User's Guide
77 CHAPTER 11
Slot Setup
11.1 Slot Setup
Use this screen, click Basic Setting > Slot Setup. To open this screen to control the power to the each slot or to change what type of card is in the slot without restarting the system.
User Guide - Page 122
...122
MS-7206 User's Guide Enter the end of VLAN(s) from being mapped to participate in a switch. to set the common settings and then make adjustments on page 106 for the specific spanning tree instance. Settings ... or remove from being mapped to the MST instance.
• Clear - It is the cost of transmitting a frame on the top navigation panel to save this row are done configuring....
User Guide - Page 175
... tag (service provider VLAN stacking or customer IEEE 802.1Q) consists of inner IEEE 802.1Q tag in the Port Setup screen.
...MS-7206 User's Guide
175 Table 50 VLAN Tag Format
Type
Priority
VID
Type is the service provider VLAN stacking tag type.
SP TPID (Service Provider Tag Protocol Identifier) is a standard Ethernet type code identifying the frame and indicates that allows the service...
User Guide - Page 187
... S.
This allows the multicast devices to update the multicast forwarding table to forward or...reports. In this case, you must manually configure the forwarding settings on the switch. The subscriber VLAN ... multicast groups are managed by IGMP snooping. Multiple subscriber devices can set your switch to...is a port on the switch, an
MS-7206 User's Guide
187 Join and leave reports from the...
User Guide - Page 196
...RADIUS vs TACACS+
RADIUS
Transport Protocol
UDP (User Datagram Protocol)
Encryption
Encrypts the password sent for authentication.
However, there is a limit on the number of users you... ) and then set up the authentication priority, activate authorization and accounting settings.
196
MS-7206 User's Guide Figure 84 AAA Server
Client
AAA Server
28.1.1 Local User Accounts
By storing user ...
User Guide - Page 197
Figure 86 RADIUS Server Setup
MS-7206 User's Guide
197 See Section 28.1.2 on page 196 for more information on the RADIUS Server Setup link in the navigation panel to configure your RADIUS server settings. Chapter 28 AAA Click Advanced Application > AAA in the AAA screen to view the screen as shown. Figure 85 AAA
28.2.1 RADIUS...
User Guide - Page 199
... the switch.
This key must be shared between the external RADIUS accounting server and the switch. Cancel
Click Cancel to begin configuring this screen afresh.
28.2.2 TACACS+ Server Setup
Use this box if you click Apply. Figure 87 TACACS+ Server Setup
MS-7206 User's Guide
199
The switch loses these changes if it is not sent...
User Guide - Page 201
... authorization and accounting settings on the external TACACS+ accounting server and the switch.
This key is deleted when you want to remove an existing TACACS+ accounting server entry ... switch. Figure 88 AAA Setup
MS-7206 User's Guide
201 Chapter 28 AAA
Table 62 TACACS+ Server Setup (continued)
LABEL
DESCRIPTION
Shared Secret
Specify a password (up to 32 alphanumeric characters...
User Guide - Page 273
... value is set in Basic Settings > General Setup.
The following...Settings > General Setup. The DHCP Relay Agent Information feature adds an Agent Information field to .
This helps provide authentication about the source of client DHCP requests that it relays to RFC 3046 for stand-alone switches. Please refer to a DHCP server by adding Relay Agent Information.
MS-7206 User's Guide...
User Guide - Page 276
See Section 10.1 on page 73 for information on how to set up management IP addresses for on the VLAN domain of the DHCP clients.
Figure 133 DHCP VLAN Setting
276
MS-7206 User's Guide
Click IP Application > DHCP in the navigation panel, then click the VLAN link In the DHCP Status screen that you want to...
ZyXEL MS-7206 and Modules Reviews
Do you have an experience with the ZyXEL MS-7206 and Modules that you would like to share?
Earn 750 points for your review!
We have not received any reviews for ZyXEL yet.
Earn 750 points for your review!