3Com 8760 - Wireless Dual Radio 11a/b/g PoE Access Point Support and Manuals
Get Help and Manuals for this 3Com item
Most Recent 3Com 8760 Questions
How Do You Connect Antenna 3com 3crweasya73/wl-575 Building To Building. Please
How do you connect antenna 3com 3crweasya73/wl-575 building to building. Please
How do you connect antenna 3com 3crweasya73/wl-575 building to building. Please
(Posted by tayoumessiegabin 2 years ago)
8760 And Multicast
(Posted by jstanley25602 9 years ago)
3Com 8760 Videos
ACCESS POINT WIRELESS 8760 DUAL RADIO 11A/B/G POE 3Com
Duration: 1:42
Total Views: 3,872
Duration: 1:42
Total Views: 3,872
Popular 3Com 8760 Manual Pages
User Guide - Page 29
... the settings for the Access Point to locate the Access Point on the same subnet to view the Access Point's system status or change the configuration: 1 Launch the 3Com Wireless Infrastructure Device Manager (Widman) utility 2 Directly connect to the Access Point. NETWORKS WITHOUT A DHCP SERVER
If your network has a DHCP server, an IP address is a DHCP server on the 3Com Installation CD...
User Guide - Page 30
....
2 Enter the Access Point's default IP address (169.254.2.1) into the CD-ROM drive. If the Configuration Management System starts, the Access Point is working correctly the following login information: „ Login name: admin „ Password: password If the Configuration Management System does not start the 3Com Wireless Infrastructure Device Manager to complete the installation.
The CD...
User Guide - Page 38
... shared key that has been distributed to encrypt transmissions passing between wireless clients and the access point. (Default: Disabled) Shared Key Setup - NOTE: All wireless devices must be entered as alphanumeric characters or hexadecimal (0~9, A~F, e.g., D7 0A 9C 7F E5). (Default: 128 bit, hexadecimal key type) 64-Bit Manual Entry: The key can contain 10 hexadecimal digits, or 5 alphanumeric...
User Guide - Page 41
... For a new access point installation, the default WLAN Service Area (ESSID) is 3Com and no security is connected to assign an IP address of the access point, or use the default address: http://169.254.2.1. To log into the access point, enter the default user name "admin" and the password "password," then press "LOGIN." Use the 3Com Wireless Infrastructure Device Manager to set . Unless it...
User Guide - Page 46
...
specific subnets. „ Default Gateway: The default gateway is used for a secure HTTP connection to obtain the IP settings for the
access point, which is the IP address of the access point. A DNS maps numerical IP addresses to domain names and can be monitored or configured from a browser. „ HTTP Port: Specifies the port to manually configure a static address for the access point...
User Guide - Page 54
...Filter - Sets the global mode for wireless-to Virtual AP (VAP) interfaces on the access point. (Default: Prevent Inter and Intra VAP client Communication) „ Disable: All clients can block specific Ethernet traffic from wireless clients. Clients can prevent communications between clients associated to -wireless communications between wireless clients and prevent access point management...
User Guide - Page 58
..., and 3 clients). SNMP is controlled by the agent. To implement SNMP management, the access point must first have an IP address and subnet mask, configured either manually or dynamically. Equipment commonly managed with MIB II. SNMP defines both the format of the access point, as well as managed objects, is maintained by the SNMP agent and used...
User Guide - Page 73
... configured to send event and error messages to four Syslog servers are stamped with a time server, so that can control error messages saved to memory or sent to a Syslog server host. (Default: Disable) Primary Server - Sets the minimum severity level for isolating access point and network problems. System Log Setup - Enables the sending of error messages. (Default: Disable) Logging Level...
User Guide - Page 78
... of up to 108 Mbps. (Default: Disabled)
4-38 The normal 802.11a wireless operation mode provides connections up to 108 Mbps. Enabling Turbo Mode allows the access point to provide connections up to radio channels and transmit power levels permitted for wireless networks in the specified country. Figure 36 Radio Settings A
Country Code - Adds a comment or description...
User Guide - Page 80
... 5 GHz channels in a European Community country, the end user and installer are transmitted from the access point. Default: 6 Mbps for 802.11a; 1, 2, 5.5, 11, Default 5.5 Mbps for 802.11b/g; They may also carry power-management information. (Range: 20-1000 TUs; Select this method when the Antenna ID is set to "3Com Integrated Antenna" to operate the device in a diversity...
User Guide - Page 93
... mechanism on the access
point, the network has no protection and is selected, you must configure at least one key on wireless clients requires a network card driver and 802.1X client software that supports the EAP authentication type that you don't set up any client, or with clients using pre-configured static shared keys. (Default: Open System...
User Guide - Page 98
... a cache.
„ Preauthentication: Each time a client roams to another access point in the access point. 2: Select TKIP when any WPA clients do not support AES. The access point advertises its supported encryption ciphers in order to enable all clients support AES.
4-58 Therefore to implement WPA2 in the network, wireless clients must enable data encryption in beacon frames and probe...
User Guide - Page 210
... Otherwise, the lowest channel is linked.
Default Setting Automatic channel selection
Command Mode Interface Configuration (Wireless)
Command Usage • The available channel settings are deployed in the same area, be sure to choose a channel separated by the access point to the same as that are available. • When multiple access points are limited by local regulations, which...
User Guide - Page 229
... of each detected access point during a rogue AP scan. Enterprise AP(if-wireless g)#
rogue-ap authenticate This command forces the unit to determine whether the access point is allowed. With authentication enabled and a configure RADIUS server, the access point checks the MAC address/Basic Service Set Identifier (BSSID) of approved access points stored on page 4-8). Example...
User Guide - Page 256
... settings on the access point match those on the clients.
Make sure that address. Try changing the wireless channel on a computer connected to the wired LAN, the 3Com Device Manager cannot find an access point.
Make sure that there are positioned properly. CHAPTER 6: TROUBLESHOOTING
Symptom
Solutions
Verify the access point configuration. Review access point firmware revisions...
3Com 8760 Reviews
We have not received any reviews for 3Com yet.