Adaptec 1210SA - Serial ATA RAID Controller Support and Manuals
Get Help and Manuals for this Adaptec item
View All Support Options Below
Free Adaptec 1210SA manuals!
Problems with Adaptec 1210SA?
Ask a Question
Free Adaptec 1210SA manuals!
Problems with Adaptec 1210SA?
Ask a Question
Most Recent Adaptec 1210SA Questions
Drivers
the adaptec 1210sa this card not 64bit driver on site adaptec so regard i want to 64bit driver
the adaptec 1210sa this card not 64bit driver on site adaptec so regard i want to 64bit driver
(Posted by abhisuryawanshi24 11 years ago)
Popular Adaptec 1210SA Manual Pages
User Guide - Page 6
...Adaptec...installed and used in accordance with the instruction manual...set out by the Spectrum Management Agency. These limits are designed to radio communications. s Increase the separation between equipment and receiver. Operation is no guarantee that may cause harmful interference to provide reasonable protection against harmful interference in a particular installation.
AAR-1210SA...part...
User Guide - Page 9
... 5-12 Deleting Arrays 5-15 Modifying Arrays 5-15 User Interface Options 5-16 Viewing Events 5-17 Event Viewer 5-17 Event Notification 5-17 Getting Help 5-19 Displaying and Modifying Properties 5-19 Controller Properties 5-19 Channel or Port Properties 5-20 Physical Device Properties 5-21
viii Contents
Installing or Updating the Driver in an Existing Linux System 3-11
4 Installing Adaptec Storage...
User Guide - Page 14
... free at www.adaptec.com.
To view this guide) s Release Notes-Before beginning your installation, review the release notes associated with the Adaptec 1210SA controller, software, and documentation. Introduction
About the Documentation
The documentation set for this kit includes: s Adaptec Serial ATA RAID 1210SA Quick Installation Guide-This
printed guide contains the essential information...
User Guide - Page 15
... array. s PCI Local Bus Specification, Revision 2.2 with PCI clock speeds
up , and configuring the controller: 1 Read and understand this entire chapter. 2 Install and configure the controller and hard drives according to 66 MHz. Introduction
Controller Features
The Adaptec 1210SA supports the following steps provide an overview of the process of installing, setting-up to
the instructions...
User Guide - Page 16
... BIOS code. Storage Management Software Overview
The Adaptec 1210SA includes the following operating systems: s Windows 2000 and Windows XP s Red Hat Linux 7.3 and 8.0 s SuSE Linux 8.1 and 8.0 For details, see Chapters 4 and 5. s Array Configuration Utility (ACU)-A DOS application used to manage your controller at register.adaptec.com. For details, see Appendix A, BIOS Utilities.
1-6 Arrays...
User Guide - Page 22
... Driver
This chapter describes installing the driver and setting up the new array for the drives attached to select from the following scenarios for installing the controller driver on Windows or Linux systems: s Installing the Driver in a New Windows System on page 3-2 s Installing the Driver in an Existing Windows System on page 3-4 s Installing Red Hat Linux 7.3 or 8.0 on page 3-6 s Installing...
User Guide - Page 24
... is finished building, insert the Windows setup CD. Then, restart the system.
3-3
The available selections are selected. Installing the Driver
8 Select the drives for the array and press Enter. 12 RAID 0 only-Select the desired stripe size. See Initializing Disk Drives on page A-6 for details.
9 Press Enter when both drives for RAID 0 or RAID 1. (For more details about...
User Guide - Page 30
... System
To update the driver in a new Linux system. Installing SuSE Linux 8.0 or 8.1
Installing the Driver in a New Linux System
In this scenario, you are installing the controller in an existing Linux system, type the following:
rpm -Uvh aar1210-*.*.*-*.i386.rpm
where * is set to the instructions in Chapter 2, Installing the Controller. 2 Create a driver disk: a Enter system setup and verify...
User Guide - Page 32
... aar1210-*.*.*-*.i386.rpm where * is the name of the driver file.
3-11
Installing the Driver 13 Select between the different creation methods for RAID 0 or
RAID 1. (For more details about the creation methods, see Step 2) and press any key to continue. 17 Follow the prompts to set up your preferred environment. 18 Continue with the Linux...
User Guide - Page 48
... select the physical devices connected to the Adaptec RAID controller.
This indicates that they display additional information. For buttons, the tips contain helpful information about the drives and enclosures attached to this controller. Selecting a channel or device will display an additional window with information and options specific to the right of devices found (excluding...
User Guide - Page 50
... when assigning hot spares or replacing a failed drive. Using Adaptec Storage Manager -
Selecting any gray segment will highlight it can see the sections Creating an Array on page 5-11, Deleting Arrays on page 5-15, and Modifying Arrays on the controller. If the controller used in the true capacity available. Browser Edition
Any part of a drive used the maximum...
User Guide - Page 60
... ports (SATA) on the
main screen for Adaptec 1210SA. s Cache size-Not available for Adaptec 1210SA. s Number of channels/ports-The number of the bus to display a dialog box with a single tab containing the following information about the selected controller: s Model-Adaptec model number. Details This window lists details of some controllers, not all three components are the version...
User Guide - Page 67
...system startup: Press for Adaptec RAID Configuration Utility
If your computer contains two or more Adaptec 1210SA controllers, a list of Arrays dialog box, select the array you want to
view and press Enter. to return to the previous menu.
Using the ACU
The Array Configuration Utility (ACU) enables you to create, manage, and delete arrays from the controller's BIOS, and initialize drives...
User Guide - Page 76
... volumes. Otherwise, the RAID tends to be limited in capacity and performance to two drives; The Adaptec 1210SA supports up to RAID capability, the Adaptec 1210SA supports a simple volume configuration, which consists of a single drive that of the smallest and slowest drive. The goal of RAID is automatically configured as a simple volume. B
Supported RAID Types
RAID is not part of an array.
User Guide - Page 81
... more members have failed. dirty data Data that can take the place of a failed component only on the fault-tolerant array to its final destination. container See array. degraded A redundant (for example, a RAID 1) array in data loss. Randomly accessible, re-writable data storage device. The array is not accessible until the clear task is explicitly assigned.
Adaptec 1210SA Reviews
We have not received any reviews for Adaptec yet.