Adaptec 2200S - SCSI RAID Controller Support and Manuals
Get Help and Manuals for this Adaptec item
View All Support Options Below
Free Adaptec 2200S manuals!
Problems with Adaptec 2200S?
Ask a Question
Free Adaptec 2200S manuals!
Problems with Adaptec 2200S?
Ask a Question
Popular Adaptec 2200S Manual Pages
Software Reference Manual - Page 12
Adaptec SCSI RAID Software Reference Guide
6 controller Commands
controller details 6-2 Syntax 6-2 Examples 6-2 Related Information 6-6
controller firmware compare 6-7 Syntax 6-7 Switches 6-7 Examples 6-7 Related Information: 6-7
controller firmware save 6-8 Syntax 6-8 Switches 6-8 Examples 6-8 Related Information: 6-9
controller firmware update 6-10 Syntax 6-10 Switches 6-10 Examples 6-10 Related...
Software Reference Manual - Page 41
.... The disk verify command with the scrub method specified. array scrub task. RAID-5 rebuild task. array reconfigure task.
File system extend task.
Table 3-7 describes the values that the Func item can display. The array create mirror and array create mmirror commands cause the MCR value to display. RAID-5 set to NTFS causes the NTF value to display. Syntax...
Software Reference Manual - Page 73
..., the command ■ Disables the read -ahead cache to optimize performance, unless your application-which means the command causes the controller to enable the array's raw array cache. If you do not want to enable the RAID-5 set's raw array cache when you create it, you can use this switch to TRUE, the command causes the...
Software Reference Manual - Page 84
... ID, and device logical unit number). Adaptec SCSI RAID Software Reference Guide
{scsi_device},{free_space}... Specifies any additional SCSI devices and associated freespaces used to optimize performance, unless your application-which means the command causes the controller to
■ Enable the read -ahead cache to create the volume set 's raw array cache when you create it, you more...
Software Reference Manual - Page 147
Examples
Before setting cache parameters for a specific array, use the container list command to no file system on it (... controller forces the enabling of the array's NVRAM write-back cache even if write data could be lost due to obtain information about any existing arrays. The NVRAM write-back cache setting for the specified array is enabled when protected.
An appropriate error ...
Software Reference Manual - Page 174
... 3.0-0 API: 3.0-0 Miniport Driver: 3.0-0 Controller Software: 3.0-0 Controller BIOS: 3.0-1 Controller Firmware: Controller Hardware: 3.3
(Build #5523) (Build #5523) (Build #5131) (Build #5478) (Build #5523) (Build #5478)
The following sections provide more information on the items that the controller details command displays.
6-2 Adaptec SCSI RAID Software Reference Guide
controller details
To...
Software Reference Manual - Page 182
...in a pair of controllers on a single controller or multiple controllers.
Examples
The following example updates a controller's firmware. Related Information:
controller commands: ■ controller firmware compare (page 6-7) ■ controller firmware save (page 6-8)
6-10 Adaptec SCSI RAID Software Reference Guide
controller firmware update
To update a controller's flash components from...
Software Reference Manual - Page 213
...clear{=boolean}] [/enable_exceptions{=boolean}][/logerr{=boolean}] [/perf{=boolean}][/report_count{=integer}] [/update{=boolean}] [{scsi_device}]
Parameters
{scsi_device} Specifies the ID for more information on... exception reporting
Syntax
disk set smart [/all disks on which you want to system administrators about potential problems caused by disk errors. error count for hard drives ...
Software Reference Manual - Page 214
... of S.M.A.R.T.
The default is , the disk set smart command does not enable S.M.A.R.T.
exception reporting for the specified disk or disks. error counts for all disks on the system.
/enable_exceptions{=boolean}
Specifies whether to enable S.M.A.R.T. error counts for the specified disk or disks. Adaptec SCSI RAID Software Reference Guide
Switches
/all{=boolean}
Specifies whether to...
Software Reference Manual - Page 220
... command can display in the partition. Adaptec SCSI RAID Software Reference Guide
The Array Num and Array Type Columns
The Array Num column displays the ID of the primary array in the Type column. This partition is part of a stripe set .
7-20 An array reconfiguration operation occurs when you use the array reconfigure command to change an array from one type to another.
Software Reference Manual - Page 284
... to 15 inclusive.
Examples
Before turning a power supply on or off, you set this version, the controller supports a maximum of a specific power supply on or off . Adaptec SCSI RAID Software Reference Guide
enclosure set power
To turn the power of a specific power supply on a specific SAF-TE enclosure management device on or off . Switches
/off{=boolean}
Specifies whether to turn the...
Software Reference Manual - Page 315
... the diskette, please read your manufacturer's instructions on how to set up to boot from the GUI on more than one ). Verify that contains the AFU utility. 3 Power on one controller, go to step c. afu update /C
To upgrade controller 0, for example, you would type the following at the DOS prompt, replacing with the GUI. Take note of...
Software Reference Manual - Page 334
...that enable you specify drive 0:0:0 in . This ensures that all drives connected to be part of the drives comprising the two arrays before creating any new arrays are other drives connected to control the various array settings during creation.
Adaptec SCSI RAID Software Reference Guide
In addition, there are created.
Any other array properties that are not specified in any new...
Software Reference Manual - Page 335
...
When using playback mode to create an array, you instruct the ACU to wait for each controller.
Because the ACU supports only a subset of the controllers and their associated array configurations in the second RAID 5's definition, the ACU initializes all the possible array configurations. If you can be set in its associated array configuration files. In addition, record mode lists...
Software Reference Manual - Page 340
... write caching is no default value. The following sections describe each of an array definition block. It accepts an optional array label value.
See page 13-23 for more than one array definition block in detail. Adaptec SCSI RAID Software Reference Guide
Table 13-4 Array Definition Block Properties
Keyword WaitForBuild
WriteCache
Required? No
No
Default Value Yes
Yes...
Adaptec 2200S Reviews
We have not received any reviews for Adaptec yet.