Adaptec LSM-FC2002 - Loop Resiliency And SES Module Expansion Support and Manuals
Get Help and Manuals for this Adaptec item
View All Support Options Below
Free Adaptec LSM-FC2002 manuals!
Problems with Adaptec LSM-FC2002?
Ask a Question
Free Adaptec LSM-FC2002 manuals!
Problems with Adaptec LSM-FC2002?
Ask a Question
Popular Adaptec LSM-FC2002 Manual Pages
Installation Guide - Page 3
... editorial errors or omissions made all times to be free from the furnishing of this manual, or operation and performance of shipment. During this manual. Basic Warranty - ADAPTEC has ..., if the customer experiences difficulties with a ADAPTEC 2Gb SANbloc system and is unable to resolve the problem via phone with ADAPTEC Technical Support a Return Material Authorization (RMA) number will...
Installation Guide - Page 4
Questionable cables should be returned to ADAPTEC, freight prepaid where they will be to repair or replace any defective product, and unless stated, pay return transportation costs for return to ADAPTEC and installation of its option and returned to cause replacement required through normal wear and tear or necessitated in whole or in part by catastrophe, fault or...
Installation Guide - Page 5
...: WWW:
321-207-2000 (RAID, FC, External Storage) 408-934-7274 (Hardware)
ask.adaptec.com
http://www.adaptec.com/support
Warranty Warranty claims must be accompanied by a Return Materials Authorization (RMA) number assigned by ADAPTEC within the applicable warranty period. A replaced product, or part thereof, shall become the property of EUROLOGIC and shall be received by...
Installation Guide - Page 7
...
Audience 13 Conventions Used In This User Guide 13 Getting Support 14 FCC Statement 14 VCCI ...15 European Community Statement 15 Safety Statements 16
Chapter 1: Introduction 19
Introduction 19 Features ...19
Disk Drive Carrier 20 Power Supplies 20 Cooling System 21 I/O Option Modules 22
Chapter 2: Installation and Setup 27
Safety Statements 28 Unpacking and...
Installation Guide - Page 8
... Operation 33 Split Fibre Channel Loop Operation (Quad Loop 34 Setting Up Split Loop Operation 34 Removing Split Loop Operation 34 Configuration Rules 35 Supported Host Bus Adapters 35 Supported Cables 36 Copper Cables 36 Optical Cables 36
Chapter 3: JBOD Configurations 37
Setting the Enclosure ID 37 Configurations 40 JBOD Configurations 41
Dual FC...
Installation Guide - Page 14
....adaptec.com
WWW http://www.adaptec.com/support
FCC Statement
WARNING: Changes or modifications to this unit not expressly approved by Eurologic Systems Ltd. 14
Getting Support
If you are designed to provide reasonable protection against harmful interference when operated in a commercial environment. This equipment has been tested and found to comply with the instruction manual...
Installation Guide - Page 20
... output power. The power supplies have conductors with Spheras Storage
Manager. • User installable, configurable and on-line maintainable. • Industry-standard 19-inch rackmount or deskside...in a 3U form factor. • Scalable to 8.2TB (112 drives), support for 15K rpm drives. • Enhanced enclosure services (SES) monitoring and reporting. • No single point of the power ...
Installation Guide - Page 27
Note: Please read this Chapter carefully before attempting to be set up of the 2Gb SANbloc Series. Important safety instructions are also described here.
Items that need to be taken. 27
Chapter 2: Installation and Setup
This Chapter describes the installation and set prior to operating the 2Gb SANbloc enclosure are discussed along with the electrical, mechanical and...
Installation Guide - Page 33
... LS module from the front of Jumpers on LS Module
Setting Fibre Channel Loop Speed (2Gb or 1Gb) Figure 2-1 Location of the enclosure. 2 On the LS Module locate the jumper position JP2 (Figure 2-1). 3 For 1Gb operation there should be no jumper installed at JP2. If
one is installed, remove it. 4 Replace the LS module.
Installation Guide - Page 36
...cables that must be used with the 2Gb SANbloc Series enclosures.
Amphenol Cable Model Numbers:
Model No. Description
515840001 .3m 2Gb Fibre Channel, copper cable, non-equalized,... Channel cables used with the 2Gb
SANbloc Series enclosure must conform to operate incorrectly.
36
Supported Cables
WARNING: Only the following APPROVED cables must be used with the 2Gb SANbloc Series enclosure...
Installation Guide - Page 46
... enclosure is powered up and all 14 drives are spun up as follows:
REMAINDER x MODE PAGE SETTING = SPIN UP DELAY (Seconds)
EXAMPLE: A typical Mode Page Setting is used for disk drive slots 0 through 13, which will support immediate drive spin up initialization routine. Modulo 8 is determined by:
(SHELF ID x DRIVE NUMBER)/8 = NUMBER + REMAINDER...
Installation Guide - Page 47
... RAID Controller Introduction
The 2Gb SANbloc RAID Controller is an intelligent, caching controller that supports RAID levels 0, 1, 3, 5, 0+1, and JBOD. It is a high performance ... a failover process. 47
Chapter 4: RAID Configurations
This chapter describes how to set up the RAID Controller:
• Controller: The controller circuit board contains the...replaced while the system is online.
Installation Guide - Page 48
... the ethernet circuit board is used, it is mounted to the disk
drive enclosure (device) and host as well as general support functions. The RAID Controller requires a minimum of -band service to the controller board. 48
host and device fibre channel input/output processors (IOPs). • I/O: The I /O, and ethernet circuit boards are...
Installation Guide - Page 50
...and a host, as well as general support functions. Features of band service for the BBU
The I/O circuit board has two SFF optical transceivers supporting shortwave multimode fibre on the host side and...supply for +3.3 V and +2.5 V • Hot pluggability for the controller • Support for the RAID controller. 50
I/O Circuit Board
Ethernet Circuit Board
• Cache DIMM memory
The I/O...
Installation Guide - Page 63
...the enclosure is powered up and all 14 drives are spun up as follows:
REMAINDER x MODE PAGE SETTING = SPIN UP DELAY (Seconds)
EXAMPLE: A typical Mode Page Setting is always between 0 and 7 (hence modulo 8).
Modulo 8
The drive spin up sequence above ,... disk drives to calculate the spin up delay. Then the LS module will support immediate drive spin up with two power supplies present.
Adaptec LSM-FC2002 Reviews
We have not received any reviews for Adaptec yet.