Campbell Scientific CM115 Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific CM115 manuals!
Problems with Campbell Scientific CM115?
Ask a Question
Free Campbell Scientific CM115 manuals!
Problems with Campbell Scientific CM115?
Ask a Question
Popular Campbell Scientific CM115 Manual Pages
CM110, CM115, CM120 Tripod Installation - Page 7
... kit is included with the CM115 and CM120 models, and is available as an option. FIGURE 1-1. A durable Tripod Tote Bag is an option for the CM110. Tripod Installation Manual Models CM110, CM115, CM120
1. General
The CM110 (10 ft), CM115 (15 ft), and CM120 (20 ft) tripods are corrosionresistant stainless steel instrument mounts that support the attachment of sensors...
CM110, CM115, CM120 Tripod Installation - Page 8
Tripod Installation Manual Models CM110, CM115, CM120
2. Specifications
CM110
CM115 (see note 3) CM120 (see note 3)
Height w/mast insert:
3 m (10 ft)
4.7 m (15.5 ft)
6.4 m (21.0 ft)
Weight:
15 kg (34 lbs)
18 kg (40 lbs)
21 kg (...
CM110, CM115, CM120 Tripod Installation - Page 9
... lightning rod, and (6) stakes. The guy kit (optional for shipment. Tripod Installation Manual Models CM110, CM115, CM120
*Anchors must hold at least 400 lbf in torpedo level side-cut ...4. The ground rod clamp, lightning rod, and ground wires are packaged separately. The CM115 and CM120 tripods include additional mast sections. Tripod Components
FIGURE 4-1 shows the tripod components...
CM110, CM115, CM120 Tripod Installation - Page 10
Tripod components
5.
Tripod Installation Manual Models CM110, CM115, CM120
FIGURE 4-1. Natural vegetation and the ground surface should be installed. With the legs extended, orient the tripod so that locks into holes located on end, and rotate the feet perpendicular to installation. Tripod Installation
5.1 Tripod Base
WARNING
Tripod installation near power lines is two ...
CM110, CM115, CM120 Tripod Installation - Page 11
... to lengthen the mast (FIGURE 5-2). Additional 56-in long insert that can be extended to the bottom section.
5 align the holes and replace the bolt. The top mast section has a 56-in the mast, and replace the bolt. Tripod Installation Manual Models CM110, CM115, CM120
Holes for Pins
5.2 Mast
Slide Collar
Spring-Loaded Pin
T-Knob
FIGURE 5-1.
CM110, CM115, CM120 Tripod Installation - Page 12
... in the bottom of the hole to allow the mast to a horizontal position.
6 typically the lower set is upright. Tripod Installation Manual Models CM110, CM115, CM120
Insert
Mast
FIGURE 5-2. Tripod mast and insert The tripod base has two sets of the hole when the mast is used (FIGURE 5-3A). The pin should be tilted down to...
CM110, CM115, CM120 Tripod Installation - Page 16
Guy cinch and lever arm 10 Tripod Installation Manual Models CM110, CM115, CM120
Phillips Screw
Lever Arm "Open" Hook
Lever Arm "Closed" FIGURE 5-6.
CM110, CM115, CM120 Tripod Installation - Page 17
... areas subjected to the ground at a 60-degree guy angle as shown in FIGURE 5-8. UTEYE anchors should be anchored at least 400 lbf.
Tripod Installation Manual Models CM110, CM115, CM120 Load End
Dead End Phillips Screw
Lever
Hook
FIGURE 5-7. Specifications for sustained wind speed and gust tolerance are given based on a 7.5-ft radius for the...
CM110, CM115, CM120 Tripod Installation - Page 18
... highlift jack through the soil until only the top half of the loop or metal ring remains above the ground. Duckbill guy anchor
12 Tripod Installation Manual Models CM110, CM115, CM120
WARNING
It is important that the anchors be driven at the correct angle will result in the anchor cable cutting through the loop...
CM110, CM115, CM120 Tripod Installation - Page 19
Top view and guy anchor layout
5.3.2 Lowering Mast after Attaching Guy Wires
Once the guy lines have been adjusted, the lever arms can be "opened" and the guy hooks removed to allow the mast to be lowered to the horizontal position.
13 Tripod Installation Manual Models CM110, CM115, CM120
Radius Distance Between Anchors CM115 7.5 ft 13 ft CM120 10 ft 17.3 ft FIGURE 5-9.
CM110, CM115, CM120 Tripod Installation - Page 20
... may not be considered. For questionable situations, additional stakes (pn 17049) or even concrete footings for securing the tripod feet to the ground.
Tripod Installation Manual Models CM110, CM115, CM120
5.4 Staking the Tripod Feet
Six stakes are provided for the tripod feet and guy anchors should be adequate depending on soil structure, maximum wind...
CM110, CM115, CM120 Tripod Installation - Page 21
... to the center of the green 12 AWG wire. FIGURE 5-11. of insulation from the ends of the tripod) using a sledgehammer or fence post driver. Tripod Installation Manual Models CM110, CM115, CM120
5.5 Tripod Grounding
Place the clamp over the ground rod and drive the rod (close to the tripod mast as shown in FIGURE 5-12...
CM110, CM115, CM120 Tripod Installation - Page 22
Tripod Installation Manual Models CM110, CM115, CM120 Lightning Rod Clamp
Ground Lug Ground Wire
Ground Lug
Enclosure Ground Lug Enclosure Ground Wire
FIGURE 5-12. Lightning rod and tripod ground lug
16
CM110, CM115, CM120 Tripod Installation - Page 23
... for wind sensors, north/south for the CM100-series tripods. Two enclosures with the -LM brackets can be ordered with a U-bolt for a 2 m mounting height. Tripod Installation Manual Models CM110, CM115, CM120
5.6 Crossarm Attachment
Attach the CM202 (2 ft, 0.6 m), CM204 (4 ft, 1.2 m), or CM206 (6 ft, 1.8 m) crossarm to the tripod mast as follows: • Remove the U-bolts, washers...
CM110, CM115, CM120 Tripod Installation - Page 32
RM Young Gill Radiation Shield 26 FIGURE 6-7. Tripod Installation Manual Models CM110, CM115, CM120
6.7 RM Young Gill Radiation Shields
RM Young Gill Radiation Shields are used to house and attach temperature and relative humidity sensors to ... as shown in FIGURE 6-7. To attach the radiation shield to a horizontal pipe, the U-bolt and plastic V-block must be moved to the other set of holes.
Campbell Scientific CM115 Reviews
We have not received any reviews for Campbell Scientific yet.