Cisco AIR-AP1252G-A-K9 Support and Manuals
Get Help and Manuals for this Cisco item
This item is in your list!
View All Support Options Below
Free Cisco AIR-AP1252G-A-K9 manuals!
Problems with Cisco AIR-AP1252G-A-K9?
Ask a Question
Free Cisco AIR-AP1252G-A-K9 manuals!
Problems with Cisco AIR-AP1252G-A-K9?
Ask a Question
Cisco AIR-AP1252G-A-K9 Videos
Popular Cisco AIR-AP1252G-A-K9 Manual Pages
Hardware Installation Guide - Page 16
... your network is located at this URL: http://www.cisco.com/techsupport/contacts
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
xvi
OL-4310-05 To open S3 and S4 service requests. (S3 and S4 service requests are those in which your production network is down or severely degraded.) Cisco engineers are those in Singapore You need your situation...
Hardware Installation Guide - Page 21
... LED signals wireless traffic over the radio interface. Green indicates that the access point is operating normally but it blinks green whenever a packet is printed on the label on the back of the channels supported by the CB20A client radio. Figure 1-1 shows the three status LEDs. OL-4310-05
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
1-3 The light...
Hardware Installation Guide - Page 23
... cable keyhole-You can use the security cable slot to secure the access point using a standard security cable, such as the central unit in an all stations together.
Central Unit in All-Wireless Network
Access point
443
OL-4310-05
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
1-5 The access point is as a root unit connected to a wired LAN or as those...
Hardware Installation Guide - Page 25
... provides the best performance for instructions on setting up an access point as a repeater. The repeater forwards traffic between wireless users and the wired LAN by sending packets to either another repeater or to an access point connected to -Point Bridge Configuration
117029
Root bridge
Non-root bridge
OL-4310-05
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
1-7
Hardware Installation Guide - Page 30
... so will result in the access point complying with regulatory requirements for environmental air space with Section 300-22(c) of the NEC.
Before Beginning the Installation
Before you begin the installation process, please refer to Figure 2-1, Figure 2-2, and Figure 2-3 to the 2.4-GHz antenna connectors. Cisco Aironet 1200 Series Access Point Hardware Installation Guide
2-4
OL-4310-05 Note If...
Hardware Installation Guide - Page 37
You can configure all the settings described in the quick start guide that shipped with your access point for the first time.
CH A P T E R
3
Configuring the Access Point for the First Time
This chapter describes how to Access the CLI, page 3-14
OL-4310-05
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
3-1 This chapter contains these sections:
• Before You ...
Hardware Installation Guide - Page 45
... the radio interfaces, follow these instructions:
Step 1 Step 2
Step 3 Step 4 Step 5 Step 6 Step 7 Step 8
Use your DHCP server, it is no default SSID. Click Settings and the radio settings page displays. Close your network. OL-4310-05
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
3-9 Click Apply. Configuring Basic Security Settings
After you must create an...
Hardware Installation Guide - Page 51
... Management Pages in the Web-Browser Interface, page 4-2 • Using Online Help, page 4-5 The web-browser interface contains management pages that you use to change access point settings, upgrade firmware, and monitor and configure other wireless devices on Windows 98, Windows 2000, and Solaris platforms.
OL-4310-05
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
4-1
Hardware Installation Guide - Page 77
...Card" section.
If you are replacing an existing 2.4-GHz radio, go to the "Removing a 2.4-GHz Radio" section. Caution The internal access point components and the 2.4-GHz radio... OL-4310-05
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
7-3 Chapter 7 2.4-GHz Radio Upgrade
Opening the Access Cover
Opening the Access Cover
To open the 2.4-GHz radio access cover, follow these...
Hardware Installation Guide - Page 91
... and two for the 1200 series access points:
• 1200 series product compliance label (AIR-AP1210-x-K9)
• 1200 series radio compliance label (AIR-RM21A-x-K9 or AIR-RM22A-x-K9)
Table 8-1 shows where to place the labels correctly:
OL-4310-05
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
8-7 The AIR-MR21A and AIR RM22A radio upgrade kits ship with regulations in...
Hardware Installation Guide - Page 92
... appears at default values. If your access point, use .
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
8-8
OL-4310-05 Table 8-1
Locations for Compliance Labels
1200 Series Model
AIR-RM21A-x-K9 or AIR-RM22A-x-K9 Radio Compliance Label
AIR-AP1210-x-K9 Product Compliance Label
AIR-AP1220A AIR-AP1230A All other models
Place over existing product compliance label. The...
Hardware Installation Guide - Page 96
... Click Radio1-802.11A and the radio status page displays. Cisco Aironet 1200 Series Access Point Hardware Installation Guide
9-4
OL-4310-05 In Cisco IOS Release 12.3(4)JAand later, the access point radio is disabled by default for instructions on enabling the radio interface. These changes to the "Configuring Basic Security Settings" section on page 3-9 for security reasons, and there is no...
Hardware Installation Guide - Page 141
...Cisco Aironet 1200 Series Access Point Hardware Installation Guide
D-5 X
-
-
36
5180
X
-
X3
X
46
5230
-
-
-
-
X3
-
124
5620
-
-
X3
X
153
5765
X
X
-
-
- Requires Cisco...
104
5520
-
- X3
-
108
5540
-
-
In Autralia and New Zealand, the AIR-RM22A-N-K9 is approved only with antenna gains of 6 dBi or less. 2. X3 -
X4
- X4
-
X4
-
-
X3...
Hardware Installation Guide - Page 144
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
D-8
OL-4310-05 Maximum Power Levels and Antenna Gains
Appendix D Channels and Antenna Settings
IEEE 802.11a (5-GHz Band)
An improper combination of power level and antenna gain can result in Chile, you must ensure that your access point Transmitter Power setting never exceeds 20 mW. When operating in equivalent isotropic ...
Hardware Installation Guide - Page 147
...Antenna Settings
Maximum Power Levels and Antenna Gains
. In Autralia and New Zealand, the AIR-RM22A-N-K9 is approved only with antenna gains of 6 dBi or less. 2.
In South Korea, the AIR-RM22A-N-K9 is approved only with Up To 9.5-dBi External Antennas...05
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
D-11 Requires Cisco IOS Release 12.3(7)JA. 4. Requires Cisco IOS...
Cisco AIR-AP1252G-A-K9 Reviews
Do you have an experience with the Cisco AIR-AP1252G-A-K9 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!