Cisco WS-X4013 - Supervisor Engine II-Plus-TS Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-X4013 manuals!
Problems with Cisco WS-X4013?
Ask a Question
Free Cisco WS-X4013 manuals!
Problems with Cisco WS-X4013?
Ask a Question
Cisco WS-X4013 Videos
Cisco WS-X4013 $425 Price Reduction
Duration: :34
Total Views: 11
Duration: :34
Total Views: 11
Cisco WS-X4013 10GE $1675 Price Reduction
Duration: :34
Total Views: 6
Duration: :34
Total Views: 6
Popular Cisco WS-X4013 Manual Pages
Hardware Maintenance Manual - Page 3
... the Sales or Service Partner, either (i) to provide a correction or a workaround for any installation, handling, maintenance, or operating instructions supplied by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software Restricted Rights clause at DFARS §252.2277013.
This Limited Warranty does not apply to Software which the error...
Hardware Maintenance Manual - Page 4
... that does not contain the defect, or (iii) refund the price paid for the Hardware less depreciation calculated on a straight-line basis. Hardware Remedies. Cisco or the Sales or Service Partner (as set forth in accordance with any installation, handling, maintenance, or operating instructions supplied by Cisco, (3) has been subjected to defective Hardware will be eligible for shipment...
Hardware Maintenance Manual - Page 5
TABLE OF CONTENTS
About This Manual xv Document Objectives xv Audience xv Document Organization xv Document Conventions xvi
Chapter 1 Cisco 4000 Series Overview 1-1 External Differences in Models of the Cisco 4000 Series 1-1 Series Specifications 1-2 Memory Systems 1-4
Chapter 2 Preparing for Installation 2-1 Safety Recommendations 2-2 Safety with Electricity 2-2 Preventing Electrostatic Discharge...
Hardware Maintenance Manual - Page 15
UniverCD is included in your local sales representative or call Customer Service.
Document Objectives
This publication contains the initial site preparation, installation, troubleshooting, and selected upgrade and maintenance procedures. For software configuration information, refer to Ordering Cisco Documentation, which is updated and shipped monthly, so it may be familiar with a DC-...
Hardware Maintenance Manual - Page 16
... Initial Hardware Configuration," includes a troubleshooting
overview, problem-solving instructions, environmental reporting features, and understanding front-panel and network-processor module LED indicators.
• Chapter 5, "Maintaining and Upgrading the Router," includes instructions for opening the
chassis, replacing or adding network processor modules, and replacing single in-line memory...
Hardware Maintenance Manual - Page 20
...-4B/NP-8B) are not compatible with the Channelized T1/ISDN PRI network interface module (NP-CT1) or with any of network processor modules.
Series Specifications
Figure 1-1 shows the front panel of the single and dual Token Ring, dual Ethernet, and FDDI modules.
1-2 Cisco 4000 Series Hardware Installation and Maintenance
Network processor modules can support two FDDI network processor...
Hardware Maintenance Manual - Page 21
...based on the MIPS R4400 and is pin-compatible. 2.
AWG-American Wire Gauge 2. Table 1-2 lists the processor and memory specifications for the Cisco 4000 series routers.
DRAM-Dynamic random access memory. 3. RAM-Random access memory. 4. Table 1-1
Cisco 4000 Series Physical Specifications
Description
Design Specification
Dimensions (W x D x H) 17.6" x 17.7" x 3.4" (44.7 cm x 45 cm x 8.6 cm...
Hardware Maintenance Manual - Page 37
...module ports support synchronous connections, and the console and auxiliary ports support asynchronous connections.
Preparing for V.35 is 2 Mbps, but 4 Mbps is commonly used.
For instance, the recommended maximum rate for Installation...D-shell connector known as EIA/TIA-232. If you understand the electrical problems that might arise and can compensate for them, you may get good ...
Hardware Maintenance Manual - Page 43
...Nine different serial cables are not interchangeable. An error message will be configured for the two versions of serial modules: both DTE and DCE versions of V.35, ...module is operating as DTE in NRZI mode, the sense of the dte-invert-timing command must also be configured with the system. This cable, available from your customer service representative, is set the jumpers for Installation...
Hardware Maintenance Manual - Page 54
... system as stated in Table 2-7. Each virtual channel is set to 120-ohm.
2-32 Cisco 4000 Series Hardware Installation and Maintenance LOOPBACK LOCAL ALARM REMOTE ALARM H3154
Network Connection Considerations
Channelized E1 Connections
The Cisco 4000 series router supports a channelized E1 (CE1) network processor module with capacitive coupling between the receive (Rx) shield and...
Hardware Maintenance Manual - Page 55
...Settings and Functions
Jumper Position
Function
J2
1 and 2
Connects the Rx shield to chassis ground.
2 and 3
Connects the Rx shield through capacitive coupling to AC. For the CE1 module, four serial cables are available from Cisco...jumper installed at J2 bypasses the AC-decoupling capacitor to ground, thereby coupling the interface directly to chassis ground. Warning To prevent problems ...
Hardware Maintenance Manual - Page 67
... following sections before connecting the BRI port of voltage that common network timing exists between compatible host chassis.
No attempt should be set up over the digital telecommunication network ISDN. The BRI network processor module is approved only for installation in a host chassis and with other terminal equipment, therefore, no effect on the capabilities...
Hardware Maintenance Manual - Page 123
...Program
The ROM monitor diagnostics help you set the configuration to booting in the standalone ROM monitor.
If you isolate or rule out hardware problems encountered when installing your router. The ROM monitor prompt... ROM monitor prompt (>) o enable the Break key and to default to 0x0, you must manually boot the system each time you can start the server in the ROM monitor:
o/r 0x0 ...
Hardware Maintenance Manual - Page 127
... Monitor Program
The ROM monitor diagnostics help you reload the router. If you set the configuration to 0x0, you will have to manually boot the system from the console each time you isolate or rule out hardware problems encountered when installing your router. Timesaver Break (system interrupt) is always enabled for 60 seconds after...
Hardware Maintenance Manual - Page 141
... 4-8 power LED indication 3-22 light 4-3 specifications 1-3 supply features 2-4 system, troubleshooting 4-2 preparing for installation 2-1 to make connections 2-7 preventing ESD damage 2-3 preventive site configuration 2-4 printing summary of ROM monitor commands problem indications 4-3 temperature 4-3 problem solving 4-1 processor specifications 1-3 protocol analyzer, attaching 2-9 publications...
Cisco WS-X4013 Reviews
We have not received any reviews for Cisco yet.