D-Link DGS-3450 - xStack Switch - Stackable Support and Manuals
Get Help and Manuals for this D-Link item
View All Support Options Below
Free D-Link DGS-3450 manuals!
Problems with D-Link DGS-3450?
Ask a Question
Free D-Link DGS-3450 manuals!
Problems with D-Link DGS-3450?
Ask a Question
Popular D-Link DGS-3450 Manual Pages
Product Manual - Page 3
... Mode Settings...38 System Log Source Interface Settings...39 System Severity Settings...39 Command Logging Settings...40 SNTP Settings ...40 Time Settings ...40 Time Zone and DST...41 MAC Notification Settings ...44 TFTP Services...44
Global Settings ...44 Port Settings...44 Multiple Image Services ...46 Firmware Information ...46 Config Firmware Image ...47 RCP ...48 RCP Server Settings...48 RCP...
Product Manual - Page 22
...VLAN Name
VID
Switch Ports
System (default)
1
Engineer
2
Marketing
3
Finance
4
Sales
5
Backbone
6
5, 6, 7, 8, 21, 22, 23, 24 9, 10, 11, 12 13, 14, 15, 16 17, 18, 19, 20 1, 2, 3, 4 25, 26
Table 2- 1 VLAN Example -
IP Interface Setup
Each VLAN must have chosen the next IP...will be terminated, and manual configuration will work. Assigned IP Interfaces
13 This addressing ...
Product Manual - Page 23
... prior to connecting to enter the VLAN Name of the xStack® DGS-3400 Series CLI Manual. Enter the appropriate IP Address and Subnet Mask. 3. NOTE: The Switch's factory default IP address is installed on the next reboot. Figure 2 - 2 IP Address Settings window
To manually assign the Switch's IP address, subnet mask, and default gateway address: 1. The Switch will need to it is...
Product Manual - Page 24
... case the actual address assigned to manage the Switch using the Command Line Interface (CLI) over the console serial port as an IP gateway. There are on VLANs other TCP/IP application (for use by a DHCP server. Setting the Switch's IP Address using the default or previously entered settings. Click Apply to the IP interface named System and the y's represent the...
Product Manual - Page 47
...)
11
FTP daemon
23
local use the "user-level" Facility. Click Apply to the Switch every time when a log event occurs on the Switch.
The default is 1 minute. System Log Save Mode Settings
This window may use 7 (local7)
Type the UDP port number used to choose a method for sending Syslog messages. Figure 2 - 32 System Log...
Product Manual - Page 56
... the specific time the firmware version was downloaded to toggle the actions between Delete and Boot. Boot Up files are five ways firmware may read "Anonymous" or "Unknown" for the Switch unless otherwise configured by an asterisk (*) next to it, it denotes a firmware upgrade through Telnet. R - If the IP address has this window, click Administration > Multiple Image Services > Config...
Product Manual - Page 138
... a certain Switch for firmware download, click its corresponding radio button under the Port heading. Will display the SIM information, including the current SIM version. Member Switches will be listed in the table and will be specified by Port (port on the CS where the MS resides), MAC Address, Model Name and Version. To update the firmware, enter the Server IP Address...
Product Manual - Page 157
... regulations apply with one set of protocols and one VLAN, with the implementation of the Double VLAN procedure. 1. Provider Edge switches must be configured as one routing behavior. Once the change of VLAN is made, all Access Control lists are enabled, GVRP must be an un-tagged port of the service provider VLANs. xStack® DGS-3400 Series Layer...
Product Manual - Page 159
... the VID for connecting Switch VLANs to configure. xStack® DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch
Figure 3 - 13 Double VLAN State Settings - View window
Parameters shown in hex form.
The tagged protocol ID of the corresponding VLAN that are for the Service Provider VLAN with an integer between 1 and 4094.
Access ports are a part of the VLAN but have yet...
Product Manual - Page 160
... allows the user to remove ports from , the Service Provider VLAN.
Delete ports - Then the highest switch number and the highest port number of the ports between switch 1, port 3 and switch 2, port 4 − in hex form to the Provider VLANs on the Switch. The following three acts to the Double VLAN State Settings window, click the Show Double VLAN Entries link. Use the From...
Product Manual - Page 219
... Ethernet Managed Switch
Q-in-Q
Q-in-Q is designed for customers who have VLAN ranges that can be supported. Customers of VLANs that overlap, which might cause restrictions on some of their configurations requiring intense processing of VLAN mapping tables which may have different or specific requirements regarding their internal VLAN IDs and the number of a service provider may...
Product Manual - Page 262
... a dash. Enter a mirror group ID. This rate is No Limit.
xStack® DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch
Priority (0-7)
Group ID (1-4) Offset
This parameter is specified to re-write the 802.1p default priority previously set specific times when this setting. Enter a value in hex form to mask the packet from the end of...
Product Manual - Page 397
...Boot configuration using the Config Current Setting menu (Save Services > Config Current Setting) • Save Log to save only the current log. • Save All to the Switch's memory. Figure 8 - 3 ...settings in saving configurations to save the current configuration file indexed as Image file 1 and save the current log.
388 xStack® DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch...
Product Manual - Page 399
...Switch. Once selected and Apply is used to select one of the Switch's Web-based management agent by clicking on the Logout button. The default setting has Configuration ID 1 as the boot up firmware... option to set the configuration file ID specified above .
• Boot_up - xStack® DGS-3400 Series Layer 2 Gigabit Ethernet Managed Switch
Current Configuration Settings
The following ...
Product Manual - Page 407
...Unit , Back Fan failed Critical
Back Fan recovered
Unit , Back Fan recovered
Critical
up/download Firmware upgraded Unit , Firmware
successfully
upgraded by console
successfully (Username:
, IP:
Informational
by console and "IP: , MAC: " are XOR shown in the System Log of this Switch. Category system
Event Description Log Information
Severity
Remark
System warm start Unit , System...
D-Link DGS-3450 Reviews
We have not received any reviews for D-Link yet.