Fender 2235 Power Amplifier Support and Manuals
Get Help and Manuals for this Fender item
View All Support Options Below
Free Fender 2235 Power Amplifier manuals!
Problems with Fender 2235 Power Amplifier?
Ask a Question
Free Fender 2235 Power Amplifier manuals!
Problems with Fender 2235 Power Amplifier?
Ask a Question
Popular Fender 2235 Power Amplifier Manual Pages
Owners Manual - Page 2
... equipped with a high efficiency forced air cooling system which allows maximum output levels into reactive (speaker) loads yet provides protection from continuous short circuits. Fender Musical Instruments 1130 Columbia St., Brea, CA 92621
1 2235
Professional Power Amplifier
Your new Fender 2235 Power Amplifier has been designed to provide high performance specifications in the Bridged Mode.
Owners Manual - Page 3
...amplifier needs service. The circuit will automatically "trip" (turn off ) if a major fault occurs inside the amplifier.
If the switch trips repeatedly (for each channel. Channel A Peak Operate w
Ch nnel
NM MO 0 Operate Peak
2235
Oft
On
logramminme
POWER... of a more conventional power switch and fuse eliminates the need to an authorized FENDER service center. INPUT LEVEL CONTROLS...
Owners Manual - Page 4
...amplifier in " position the amplifier is fed to both channels are available from unbalanced circuits. Both input attenuators are active. The output is used the two channels operate independently. NO USER SERVICE/5 5LE PARTS INSIDE. specifies a 20-amp limit on each 2235...or transformer) or from FENDER as a kit. ...power operation is full range music or speech. Normal electrical code...
Owners Manual - Page 5
...-foot run a line-level signal cable over the long distance to transfer all the amplifier's power without the need for connection, only one or two strands will be it are heavy... smallest wires (the highest numbered gauges) recommended for American Wire Gauge.
In cases where speakers and power amplifiers are located far away from it a mixer or a preamp), "balanced line" signal cables are...
Owners Manual - Page 6
...those of the Fender amplifiers. The 2235 is timed to turn on the speaker outputs after the amplifier's power supply is rated ... the settings of the necessary controls.
In multiple amplifier installations, we recommend sequential turn on the power amplifier last....power you 've mounted all the equipment on at once with a switched power receptacle "strip," be sure to turn -on (either manually...
Owners Manual - Page 7
... speaker system is noisy (hissy), reduce the setting of the source's controls and the amplifier's controls until the sound level from clipping caused by one "click" and repeat this manual about the current capability of 120 volt, 50-60Hz AC power. You must "juggle" the settings of the 2235 INPUT LEVEL control(s) by excessive output demands...
Owners Manual - Page 8
SPECIFICATIONS
Output Power Continuous sine wave output power, both channels driven, 20Hz to 20kHz at less than 0.1% THD: 8 ohms 4 ohms Single channel driven, 1kHz, 1% THD (power at clip): 8 ohms 4 ohms
Frequency Response Power Bandwidth
IMD (SMPTE) Hum & Noise Damping Factor Rise Time Slew Rate Channel Separation Input Impedance Sensitivity Power Requirements Weight Dimensions
200 Watts 350 ...
Owners Manual - Page 9
POWER AMPLIFIER
CHANNEL B OUTPUT
0 •
+
FENDER 2235 POWER AMPLIFIER BLOCK DIAGRAM
8
CHANNEL A INPUT
AIM
CHANNEL B INPUT
v4--J A f .' CH A ATTENUATOR
DIFFERENTIAL AMPLIFIER
POWER AMPLIFIER
CHANNEL A OUTPUT
0 +
STEREO
350W, 40 MINIMUM LOAD
PROTECTION LINK
DIFFERENTIAL AMPLIFIER
CH B ATTENUATOR BRIDGED
MIMI!
IIIIRMIlla 4INIIII.
Fender 2235 Power Amplifier Reviews
We have not received any reviews for Fender yet.