Fluke 271-U 115V Support and Manuals
Get Help and Manuals for this Fluke item
This item is in your list!
View All Support Options Below
Free Fluke 271-U 115V manuals!
Problems with Fluke 271-U 115V?
Ask a Question
Free Fluke 271-U 115V manuals!
Problems with Fluke 271-U 115V?
Ask a Question
Popular Fluke 271-U 115V Manual Pages
Product Manual - Page 2
... substantially in accordance with a description of mechanical components, Fluke will be free from defects in transit. Parts, product repairs, and services are warranted for 90 days and that software will not affect the validity or enforceability of shipment. Warranty support is available only if product is returned to a Fluke authorized service center within the warranty period.
Product Manual - Page 4
... dry cloth to the accompanying documentation, incorrect operation may be disposed of replacement becoming necessary, replace only with solid waste stream. refer to clean the LCD window.
Warning...271
Users Manual
Note This instrument uses a Lithium button cell for Fluke products online at: www.
.com 1.888.610.7664
Typical battery life is 5 years. Contact your authorized Fluke Service...
Product Manual - Page 6
iv
MyFlukeStore Shop for any reason ensure that all case screws are remade correctly before replacing the cover. 271
Users Manual
b) after opening the case for Fluke products online at: www.
.com 1.888.610.7664 Refer to the Service Manual. c) In the event of part replacement becoming necessary, only use components of an identical type.
Always ensure all signal...
Product Manual - Page 8
... Warning and Error Messages 5-6 The Auxiliary Output 5-7 Auxiliary Output Phase 5-8 Waveform Generation Options 5-9 Square Wave Generation 5-9 Filter ...5-9 Auxiliary Output 5-10 Frequency Stop 5-10 Trigger/Sweep Output 5-10
6
Sweep Operation 6-1
Introduction...6-2 Connections for Sweep Operation 6-2 Setting Sweep Span and Markers 6-2
vi
MyFlukeStore Shop for Fluke products online...
Product Manual - Page 10
... Addressable RS232 Interface Control Codes 16-6 GPIB Interface 16-6 GPIB Subsets 16-6 GPIB IEEE Std. 488.2 Error Handling 16-6 GPIB Parallel Poll 16-7 Status Reporting 16-7 Standard Event Status and Standard Event Status Enable Registers......... 16-8 Status Byte Register and Service Request Enable Register 16-8 Status Model 16-9 Power on Settings 16-9
Remote Commands 16...
Product Manual - Page 18
...setting. Frequency Shift Keying (FSK)
Phase coherent switching between two selected frequencies at : www.
.com 1.888.610.7664 Manual (front panel key), internal trigger generator, external signal or remote interface.
1-6
MyFlukeStore Shop for Fluke... free run or triggered manually (front panel key), by the switching signal source. See VCA In below. 271
Users Manual
Trigger and burst
Phase-...
Product Manual - Page 20
...100 kHz. 2.5 V for Fluke products online at maximum output.
Output logic levels nominally 1 V and 4 V from typically 50 Ω.
Keyboard selection of mode, waveform etc. Installation category II. typically 6 k...instrument set-ups may be addressed from these sockets are available through the RS232 or GPIB interfaces. Up to phase lock two or more generators. 271
Users Manual
Inputs...
Product Manual - Page 24
... earthed. When a three core mains lead with feet for the local supply. A rack kit for mounting in Appendix A.
271
Users Manual
Mains Operating Voltage
Check that the correct mains fuse is fitted for Fluke products online at: www.
.com 1.888.610.7664 The correct mains fuse types are listed in a 19 inch rack...
Product Manual - Page 26
271
Users Manual
Front Panel Connections
MAIN OUT MAIN OUT is made
available at : www.
.com 1.888.610.7664
AUX OUT logic levels ...for 60 seconds. AUX OUT AUX OUT is TTL/CMOS compatible.
3-2
MyFlukeStore Shop for Fluke products online at the socket. EXT TRIG EXT TRIG is the default setting. OUTPUT
This is the external trigger input for the main output but the phase relationship ...
Product Manual - Page 28
271
Users Manual
RS232
The rear panel carries a ...LE0 SR1 RL1 PP1 DC1 DT1 C0 E2
The GPIB address is not isolated; It is set from instrument
3
RXD Received data to instrument
4
- the GPIB signal grounds are connected ...the front panel using the REMOTE menu.
3-4
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664 Pins 7, 8 and 9 are shown below:
Pin Name ...
Product Manual - Page 30
...the instrument for Fluke products online at ...specification; The method delivers low phase noise and low distortion.
4.
The major advantages of the crystal oscillator.
2. This is not a problem with sine waves which, because they are easily generated.
7. all waveforms are given later in later sections starting with waveforms; 271
Users Manual....
if an error is covered in...
Product Manual - Page 32
...in turn determine the lowest or highest setting that can be found as the frequency...on the next, and back again. 271
Users Manual
Numeric entries are automatically confirmed when ...the appropriate unit key (Hz, kHz, MHz, etc.) is pressed but ENTER can be stepped into that field. phase) or no alternative form for the parameter (for Fluke...
Product Manual - Page 96
...Error bit to be set in the Standard Event Status Register, a value of Addressable RS232 Interface Control Codes
02H Set Addressable Mode. 03H Universal Unaddress control code. 04H Lock Non-Addressable mode control code...Status Reporting below for Fluke products online at: ...
L4
Service Request
SR1
Remote ...271
Users Manual
Full List of 1 to be placed in the Query Error Register and the parser to ...
Product Manual - Page 98
...1.888.610.7664 Set when an error is read by the *STB? INTERRUPTED error 2.
Status Byte Register and Service Request Enable Register
...271
Users Manual
Standard Event Status and Standard Event Status Enable Registers
These two registers are implemented as required by the IEEE standard 488.2.
Any bits set in the Standard Event Status Register which correspond to bits set in the Service...
Product Manual - Page 106
... is
Wait for Fluke products online at: www.
.com 1.888.610.7664
The syntax of the software installed.
GPIB Group Execute...271
Users Manual
*OPC?
*PRE *PRE?
*SRE *SRE?
*STB? *WAI
Query operation complete status. The response will be available immediately the command is 1.
The syntax of the response is executed because of the sequential nature of instrument and is
Set the Service...
Fluke 271-U 115V Reviews
Do you have an experience with the Fluke 271-U 115V that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fluke yet.
Earn 750 points for your review!