Fluke 7103-TR-156 Support and Manuals
Get Help and Manuals for this Fluke item
This item is in your list!
View All Support Options Below
Free Fluke 7103-TR-156 manuals!
Problems with Fluke 7103-TR-156?
Ask a Question
Free Fluke 7103-TR-156 manuals!
Problems with Fluke 7103-TR-156?
Ask a Question
Popular Fluke 7103-TR-156 Manual Pages
Product Manual - Page 2
... warranty on non-defective media. Fluke does not warrant that service center, with its functional specifications for 90 days and that failure was caused by neglect, misuse, contamination, alteration, accident, or abnormal condition of operation or handling, including overvoltage failures caused by accident or abnormal conditions of repair/replacement parts when product purchased in one...
Product Manual - Page 3
... Used 1
1.2 Safety Information 2
1.2.1
Warnings 2
1.2.2
Cautions ...4
1.3 Authorized Service Centers 5
2 Introduction 7
3 Specifications and Environmental Conditions 9
3.1 Specifications 9 3.2 Environmental Conditions 9
4 Quick Start 11
4.1 Unpacking 11 4.2 Setup ...11 4.3 Power ...12 4.4 Setting the Temperature 12
5 Installation 13
5.1 Bath Environment 13 5.2 "Dry-out...
Product Manual - Page 10
... user's guide. 7103 Micro-Bath User's Guide
Safety Information
Symbol
Description
OVERVOLTAGE (Installation) CATEGORY ...in the user's manual.
2
MyFlukeStore Shop for temperature calibration. DO NOT install access cover without... holes onto a bath that may damage the instrument
being used at : www.
.com 1.888.610.7664 The instrument was designed for Fluke...
Product Manual - Page 12
7103 Micro-Bath User's Guide
Safety Information
ELECTRICAL HAZARD
These guidelines must be installed in accordance with local codes and ordinances or adapter ... Hart Scientific Authorized Service Center.
If this instrument under a cabinet or other structure. The correct setting of these parameters is important to contact with one of a component part. DO NOT operate this ...
Product Manual - Page 14
.... The 7103 Micro-Bath was designed for portability, low cost, and ease of the calibrator as described in the instruction manual.
7
... scan rate control L Temperature switch hold L Eight Set-point memory L Adjustable readout in the lab. The controller uses a precision ...RTD as a portable instrument or bench top temperature calibrator for Fluke products online at: www.
.com 1.888.610.7664 ...
Product Manual - Page 15
... Hz, 400 W Overvoltage (Installation) Category II, Pollution Degree 2 per IEC 61010-01 250 V 5 A F(fast acting) NO USER SERVICEABLE PARTS
3.2 Environmental Conditions
Although the ...trouble-free operation, it must be operated in the Maintenance Section of this manual. Specifications and Environmental Conditions
Specifications
3 Specifications and Environmental Conditions
3.1 Specifications...
Product Manual - Page 16
...
L 7103 Micro-Bath L Transport/Pour Access Lid L Probe Basket L Stir Bar L Power Cord L Manual L Access Cover, if purchased
4.2 Setup
Caution: DO NOT operate the instrument without fluid. The set-point temperature...and void the warranty.
4.1 Unpacking
Unpack the Micro-Bath carefully and inspect it for Fluke products online at room temperature (25°C) into the bath and heating the unit ...
Product Manual - Page 17
7103 Micro-Bath User's Guide
Power
Turn on the power to the calibrator by toggling the switch on and begin normal operation.
Press "EXIT" to return to operate please check the power connection. If the unit fails to the temperature display. Refer to Section 3.1, Specifications, for Fluke products online at: www.
.com...
Product Manual - Page 20
...General
Caution: Read before placing the bath in service
The information in this section is not totally ...set -point temperature.
6.2 Comparison Calibration
Comparison calibration involves testing a probe (unit under test, UUT) against a reference probe. It is completely dry before inserting it to prevent stem effect. Refer to Section 8.3, Bath Fluid, and subsequent subsections for Fluke...
Product Manual - Page 39
...
MyFlukeStore Shop for Fluke products online at a specified rate (degrees per minute. Sc=On
Scan function on
Press "SET" to accept the present setting and continue.
2 Accept scan setting
9.3.2
Scan Rate
... when cooling. This is the scan rate.
7103 Micro-Bath User's Guide
Scan
Un= F
New units selected
9.3 Scan
The scan rate can be set and enabled so that appears in the main...
Product Manual - Page 40
... available for Fluke products online at which the switch is activated does not affect the set -point temperature. The status flashes when the switch is open when the set -point from...Display Hold
9.4 Temperature Display Hold
The 7103 has a display hold function which allows action of an external switch to freeze the displayed temperature and stop the set -point is changed, the closed and...
Product Manual - Page 46
... device of origin. Access to these values to enter the menu.
41
MyFlukeStore Shop for Fluke products online at the factory and should have a list of any carriage-return. The correct setting of these constants and their settings with manual. This parameter enables (on) or disables (off) transmission of a linefeed character (LF, ASCII 10...
Product Manual - Page 48
... serial interface parameters menu is installed with and being controlled by programming... 6 DSR 7 RTS 8 CTS 9 NC
10.1.2
Setup
Before operation the serial interface must be set -point temperature, monitor the temperature, and access any of...SET" repeatedly until the serial interface menu is capable of the functions, parameters and settings discussed in length. RS-232 Cable Wiring for Fluke...
Product Manual - Page 51
... Numeric data supplied by a carriage return and linefeed. 7103 Micro-Bath User's Guide
Interface Commands
Table 5 Controller Communications Commands
Command Description
Command Format Command Example Returned
Returned Example Acceptable Values
Display Temperature
Read current set-point
s[etpoint]
s
set: 999.99 {C or F} set: 150.00 C
Set current set to FULL and a command is sent to READ...
Product Manual - Page 60
... section may help to have the model number and serial number of your instrument available. Be sure to find and solve the problem. Allow the instrument to stabilize and verify the accuracy of the temperature reading. Check the Scan and Scan Rate settings. an ADC ready error
Initialize the system by performing the...
Fluke 7103-TR-156 Reviews
Do you have an experience with the Fluke 7103-TR-156 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Fluke yet.
Earn 750 points for your review!