Fluke Calibration 1551A-12-DL Support and Manuals
Get Help and Manuals for this Fluke item
View All Support Options Below
Free Fluke Calibration 1551A-12-DL manuals!
Problems with Fluke Calibration 1551A-12-DL?
Ask a Question
Free Fluke Calibration 1551A-12-DL manuals!
Problems with Fluke Calibration 1551A-12-DL?
Ask a Question
Popular Fluke Calibration 1551A-12-DL Manual Pages
Calibration Guide - Page 1
1551A Ex/1552A Ex
Stik Thermometer
Calibration Manual
November 2010 © 2010 Fluke Corporation. All product names are subject to change without notice. All rights reserved. Printed in USA. Specifications are trademarks of their respective companies.
Calibration Guide - Page 2
... is one country is submitted for 90 days and that service center, with its functional specifications for repair in Fluke's opinion, has been misused, altered, neglected, contaminated, or damaged by a court or other provision.
Fluke reserves the right to invoice Buyer for importation costs of repair/replacement parts when product purchased in one year and begins on new...
Calibration Guide - Page 3
... Fluke 1 Safety Information 2
ATEX Safety Information 3 Symbols ...3 Approvals ...4 Specifications...4 Calibration ...5 Overview ...5 Recommended Equipment 6 Initial Setup 6 Record as-found Calibration Parameters 7 Evaluate as-found Measurement Errors 7 Adjustment at the Low Calibration Point 8 Adjustment at the Zero Calibration Point 9 Adjustment at the High Calibration Point 9 Set...
Calibration Guide - Page 9
... at www.fluke.com. For complete usage instructions, see , print, or download the latest manual supplement, visit http://us.fluke.com/usen/support/manuals.
1 Introduction
The Stik Thermometer (the Product) is a precision digital thermometer that can be used in many of the same hazardous locations as analog thermometers. To see the 1551A Ex/1552A Ex Users Manual. It...
Calibration Guide - Page 10
.... If you open the Product case.
1551A Ex/1552A Ex
Calibration Manual
Safety Information
A Warning identifies conditions and actions...Replace the batteries when the low battery indicator shows to the manufacturer for inspection. • The Product is intended for installation...Product to the user. Refer
to the battery replacement instructions for proper operation of data. Should the Product...
Calibration Guide - Page 11
... cause a safety risk. To make sure of safe Product operation, fully follow these instructions, personal injury or Product damage can occur. These areas are not sure (due to translation and/or printing errors), refer to the English manual. Table 1. See Manual. Substitution of Danger. Important information. X Hazardous Voltage
Do not dispose of this product...
Calibration Guide - Page 12
...Manufactured by Fluke Corporation: Fluke Corporation P.O. 1551A Ex/1552A Ex
Calibration Manual
Approvals The Product meets the above requirements using: EN 60079-0:2006 ELECTRICAL APPARATUS FOR EXPLOSIVE GAS ATMOSPHERES --
P.O. PART 0: GENERAL REQUIREMENTS (IEC 60079-0:2004 (MOD))
EN 60079-11:2007 EXPLOSIVE ATMOSPHERES -- Box 1186 5602 BD Eindhoven The Netherlands
Specifications
(Ambient: 23...
Calibration Guide - Page 13
... as-left measurement errors • Record as-left calibration parameters values
5 Probe Size 1551A-9: 4.8 mm x 229 mm (3/16 in . x 20 in.) 1552A: 6.35 mm x 305 mm (1/4 in . Each laboratory should only be adjusted to 30 minutes or can be performed by an uncertainty analysis also based on their own specific procedure based on the...
Calibration Guide - Page 14
... in the Setup menu. 1551A Ex/1552A Ex
Calibration Manual
Recommended Equipment The equipment listed in the Product and replace them if necessary. The battery level indication is usually 9600 but may be set to communicate with the 1551A Ex/1552A Ex Thermometer
Initial Setup Check the batteries in Table 2 will satisfy the calibration requirements:
Table 2.
Several settings in the...
Calibration Guide - Page 15
Stik Thermometer
Calibration
Record as -found Measurement Errors The Product should be recorded. As-found Calibration Parameters Before any adjustments are made , the present values of the bath, reference thermometer, and 1551A Ex/1552A Ex Thermometer are given in Table 4, depending on the model. Evaluate as -found Calibration Parameters
Parameter
Command
Value (fill in)
TEMP1 ADJ1...
Calibration Guide - Page 16
... Ex
Calibration Manual
At each calibration point the measurement error may be necessary to measure the given temperature accurately. Low-Adjustment Temperature
Point Low
−50 °C
1551A Ex
−80 °C
1552A Ex
Before adjustments to any calibration parameters can be enabled by sending the following command:
CAL:USER:LOW
The parameter is the current password...
Calibration Guide - Page 17
...1551A Ex 0 °C
0 °C
1552A Ex
To make an automatic adjustment at the High calibration...Calibration Point The final adjustment is made for the high end of the temperature range of the Product. Set...This adjustment will set the value ...
Calibration
Adjustment at the Zero Calibration Point...1551A Ex 157 °C
300 °C
1552A Ex
To make an automatic adjustment at the Zero calibration...
Calibration Guide - Page 18
... to a final test to measure the given temperature accurately.
The measurements are collected and errors are evaluated in the same way that was explained in )
10 Point 1 2 3 4 5
Table 9. 1551A Ex/1552A Ex
Calibration Manual
The command will set , protection of the calibration parameters should be restored using the following command:
SYST:PASS:CDIS
(Protection will always...
Calibration Guide - Page 19
...3. HANDLE S.S. DEVICES BY THE BODY.
static awareness
A Message From
Fluke Corporation
Some semiconductors and custom IC's can minimize the chances of destroying...following practices should be damaged by :
1. KEEP PARTS IN ORIGINAL CONTAINERS UNTIL READY FOR USE.
4. Using the procedures, packaging, and
bench techniques that there is a problem. 2. This notice explains how you can be...
Calibration Guide - Page 22
... rating. 4.
Battery Alkaline AAA
Figure 1. Replace the battery door and install the screw. Remove the battery door to remove the battery door screw. 2.
Battery Replacement
Table 11. Use a flat-blade screwdriver...
gjo003.eps
12 Replace only with approved AAA batteries listed in this document. 1551A Ex/1552A Ex
Calibration Manual
To change the batteries, see Figure 1: 1.
Fluke Calibration 1551A-12-DL Reviews
We have not received any reviews for Fluke yet.