Ganz Security ZN-MDI243M-IR Support and Manuals
Get Help and Manuals for this Ganz Security item
This item is in your list!
View All Support Options Below
Free Ganz Security ZN-MDI243M-IR manuals!
Problems with Ganz Security ZN-MDI243M-IR?
Ask a Question
Free Ganz Security ZN-MDI243M-IR manuals!
Problems with Ganz Security ZN-MDI243M-IR?
Ask a Question
Popular Ganz Security ZN-MDI243M-IR Manual Pages
PixelPro Indoor Mini Dome Specifications - Page 2
... Explorer 7.0 or above, Firefox, Chrome, Smart Phone
Security
Password Protection
SDK (API)
HTML based API
VMD (Video Motion Detection)
User set 4 ROI (Region of Interest) 10 Step Sensitivity
Alarm... Specifications
Check our website for updates on additional software partners
Models Camera Analog Network Power Additional
ZN-MDI243M-IR
Image Sensor
1/2.8" Sony Exmor CMOS Sensor
Max....
Manual - Page 2
... fallen into the apparatus, the apparatus has been exposed to do so.
Install in accordance with the manufacturer's
instructions. 8) Do not install near water. 6) Clean only with a dry cloth. 7) Do not block any of electric shock does not perform any servicing other apparatus
that contained in any heat sources such as power supply cord...
Manual - Page 4
... (IEEE 802.3af) support power to the camera to be connected to a network secured with the powerful GANZ PixelPro Camera Management tool, which is a high performance H.264 network camera, designed for a power outlet and reducing installation costs. Steady power could be guaranteed with each GANZ PixelPro camera.
4 Product Features
The GANZ PixelPro (ZN-MDI243M-IR)) is provided on the...
Manual - Page 5
... or incorrect power is started .
Factory Default is supplied. On Flash
System Status Steady for service monitor
This analog video output is started .
3. Status LED
LED Color Green Unlit Red
Indication On
Flash
- Network connector
The GANZ PixelPro (ZN-MB243M) connects to the network via Power over Ethernet (PoE). No network connection established...
Manual - Page 10
...lens position. Select the 'Video Format'. 2. For security reasons this button by manually to stop streaming
NOTE: It is usually done on a specific port. Adjust lens position.
2.4 The Live View ...Play: Click this button by manually to the documentation for router/firewall for further instructions.
2.3 Adjusting the Image angle
To adjust the image angle. 1. Select the Setup tab, and open the ...
Manual - Page 11
...be supported) provides the most efficient usage of bandwidth, especially when there are lost due to network problems. This... single stream of information to multiple network recipients. Setting the preferred method(s) is an alternative to the ... Datagram Protocol) is a communications protocol that offers limited service for the stream. RTSP is used primarily on delimited networks...
Manual - Page 12
...1. Start your web browser and enter the IP address or host name of 10 unicast viewers, note that all settings under the Setup tab. Click on the network until a client connects and requests the stream. RTP/RTSP This unicast method is now... is relatively simple to configure firewalls to allow RTSP traffic.
3. However, as 1 unicast viewer. The Setup
The GANZ PixelPro is no video traffic on the...
Manual - Page 17
... image background is in the image appear consistent, compensating for low light behavior determine how the camera behaves sat low light levels. The GANZ PixelPro camera can be set manually..
5.2.4 Image Property Control
Modify the video signal parameters, such as: Brightness, Sharpness, Contrast, and Color. If necessary, the type of the image. Sharpness...
Manual - Page 18
...(TCP) Buffering Time (frame based) Determines (0 ~ 90) x 1/30 sec (0 ~ 3sec) Viewer OSD Setup Date : Determines whether the date is displayed. Event State : Determines whether the event state is shown on the ... camera title is displayed. Live
6.1 Setup
The GANZ PixelPro could support unlimited number of multicast, the GANZ PixelPro could support 10 simultaneous users. In case of users. If...
Manual - Page 24
...
9.1 Network > IP Setup
Network Settings Click the Setup > Network > IP Setup to IP addresses on ...update a DNS server, you could be set manually. Both versions may be enabled simultaneously, and at least one version should be set automatically via
e.g. When using the Internet Dynamic DNS Service. If IPv6 is unavailable.
24 9. IP Address Configuration The GANZ PixelPro supports...
Manual - Page 26
RTSP port- The default setting is useful for simple port mapping. Only certain IP addresses and port numbers should be... connect automatically.
9.3 Network > RTP
RTP port range , Multicast Setup These settings are the IP address, port number, and Time-To-Live value to start an H.264 stream. This is 554. 9.2 Network > Service Port
Service Port HTTP port- The default HTTP port number (80) could...
Manual - Page 31
... of the camera, follow the instruction below. Factory Default To reset the camera settings to Firmware Upgrade mode.
31 10.3 System > Maintenance
System Name Choose a system name to identify the camera when using e-mail notifications. System Reboot Reboot the camera. Enable Firmware Upgrade / Firmware Updates
To upgrade Firmware of Enable Firmware Upgrade menu.
2) The camera automatically...
Quick Start - Page 1
... the Network camera away from water. Physical Description
Ver1.00 EN
1
Quick User Guide
ZN-MDI243M-IR Network Camera
Warning before installation
-Power off immediately. -Do not place the Network camera near heat sources, such as a television or oven. -Refer to your instruction manual for installation
Video monitor cable
Tapping Screw M4x30 : 2pcs
Anchor : 2pcs
2. If the Network...
Quick Start - Page 2
...support PoE only.
4. Assign IP address
The default setting of the camera is set to "DHCP" and "UPnP" function is set ...to the PoE HUB. Making Connection
Connect Ethernet cable to make a connection to ON. If a DHCP server is enabled on your PC you can find the network camera in "My network". Execute MultiUpgradeTool.exe. It will be shown as 255.255.255.255. Quick User Guide
ZN-MDI243M-IR...
Quick Start - Page 3
....
For further information for setup, please refer to "ADMIN" and "1234".
Default User and Password are set to User's manual in software CD. When double click the camera in the list, the default web browser (Internet Explorer or compatible equivalent) will open and automatically connect to the camera.
Quick User Guide
ZN-MDI243M-IR Network Camera
1) After the...
Ganz Security ZN-MDI243M-IR Reviews
Do you have an experience with the Ganz Security ZN-MDI243M-IR that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Ganz Security yet.
Earn 750 points for your review!