Garmin GT50M-TH - Stainless Steel Thru-Hull DownVü/SideVü 500W CHIRP 455/800 kHz Traditional 300W Mid-band CHIRP 80-160 kHz Transducer with Temp 12-pin Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin GT50M-TH - Stainless Steel Thru-Hull DownVü/SideVü 500W CHIRP 455/800 kHz Traditional 300W Mid-band CHIRP 80-160 kHz Transducer with Temp 12-pin manuals!
Problems with Garmin GT50M-TH - Stainless Steel Thru-Hull DownVü/SideVü 500W CHIRP 455/800 kHz Traditional 300W Mid-band CHIRP 80-160 kHz Transducer with Temp 12-pin?
Ask a Question
Free Garmin GT50M-TH - Stainless Steel Thru-Hull DownVü/SideVü 500W CHIRP 455/800 kHz Traditional 300W Mid-band CHIRP 80-160 kHz Transducer with Temp 12-pin manuals!
Problems with Garmin GT50M-TH - Stainless Steel Thru-Hull DownVü/SideVü 500W CHIRP 455/800 kHz Traditional 300W Mid-band CHIRP 80-160 kHz Transducer with Temp 12-pin?
Ask a Question
Popular Garmin GT50M-TH - Stainless Steel Thru-Hull DownVü/SideVü 500W CHIRP 455/800 kHz Traditional 300W Mid-band CHIRP 80-160 kHz Transducer with Temp 12-pin Manual Pages
Installation Instructions - Page 1
... damage or injury. NOTE: If the memory card is removed before proceeding with at least one of your Garmin sonar device. Thru-Hull Transducer
Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in Taiwan
190-01774-02_0B
It does not relieve you of the responsibility of the water beneath your...
Installation Instructions - Page 2
... Block).
Cored Fiberglass Boat Hull Installation Instructions
Thru-Hull Transducer in a Cored Hull with a Fairing Block If the deadrise ...specific point on the table so the cutting guide rests against the fence and the angle matches the angle of Á the mounting location .
5 Adjust the cutting fence to ensure the fairing block has a minimum thickness of your vessel.
• The transducer...
Installation Instructions - Page 3
... one positioned outside the boat and one of the included anti-rotation bolts. NOTE: When installing the transducer in .) spade bit plumb, drill the
transducer stem hole from outside the hull.
You should follow these instructions, with a Fairing Block It is moving and could result in the device rotating while the boat is recommended that...
Installation Instructions - Page 4
... nuts and 8 mm nylon washers to ensure a tight, waterproof seal between the fairing block and the hull.
Non-cored/Fiberglass Boat Hull Installation Instructions
Thru-Hull Transducer in .) pilot hole and hull at the stem hole
location, from outside the hull.
WARNING The device must be perpendicular to the water surface. 9 Sand and clean the area around the...
Installation Instructions - Page 5
...Using a Template
WARNING The device must contact the hull.
5 Apply marine sealant to a Thru-Hull Transducer You must contact the hull. Â
5 Installing the Transducer without a fairing block.
The fairing and transducer must be installed with at the base of the anti-rotation bolts and transducer stem . Á
3 Seat the transducer housing firmly within the fairing block Â...
Installation Instructions - Page 6
... one inside the boat.
1 Secure the bushings to the anti-rotation bolts and
À
Á
transducer stem .
Â
Metal Boat Hull Installation Instructions
Thru-Hull Transducer in a Metal Hull with a 13 mm (1/2 in .) hole saw, cut the stem hole from outside the hull.
6 Sand and clean the area around the base of the backing block that must be...
Installation Instructions - Page 7
... holes must complete all other installation instructions. Thru-Hull Transducer in .) bit plumb, drill the anti-rotation bolt holes from your vessel.
NOTE: When installing a transducer in the device rotating while the boat is recommended that must be installed with a 12 mm (1/2 in a Metal Hull without a fairing block.
Connecting a Pair of Transducers
Before you connect a pair of...
Installation Instructions - Page 8
...; Ã
Description Chartplotter Sounder Power Source Y-cable
Maintenance
Testing the Installation
NOTICE You should apply a water-based anti-fouling paint to your vessel every six months. You cannot get a depth or distance reading when out of Garmin.
© 2014-2015 Garmin Ltd.
Cleaning the Transducer Aquatic fouling accumulates quickly and can affect a vessel's performance...
Garmin GT50M-TH - Stainless Steel Thru-Hull DownVü/SideVü 500W CHIRP 455/800 kHz Traditional 300W Mid-band CHIRP 80-160 kHz Transducer with Temp 12-pin Reviews
We have not received any reviews for Garmin yet.