?Important Safety and Product Information
Page 2
... device may not cause interference, and (2) this device must accept any user-serviceable parts. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE. Failure to radio communications if not installed and used with Garmin authorized accessories. Product Environmental Programs Information about the Garmin® product recycling program and WEEE, RoHS, REACH, and other reasonably...
... device may not cause interference, and (2) this device must accept any user-serviceable parts. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE. Failure to radio communications if not installed and used with Garmin authorized accessories. Product Environmental Programs Information about the Garmin® product recycling program and WEEE, RoHS, REACH, and other reasonably...
?Important Safety and Product Information
Page 20
Garmin WEEE、RoHS、REACH www.garmin.com / aboutGarmin / environment Garmin 1999/5/EC www.garmin.com/ compliance Garmin Garmin Garmin i ii iii iv) 由于非 Garmin v) 未经 Garmin iv) 连接非 Garmin Garmin Garmin 90 90 1 Garmin Garmin Garmin Garmin RMA Garmin Garmin Garmin Garmin Garmin www.garmin.com/ support / warranty .html Garmin Marine Warranty Policy 20
Garmin WEEE、RoHS、REACH www.garmin.com / aboutGarmin / environment Garmin 1999/5/EC www.garmin.com/ compliance Garmin Garmin Garmin i ii iii iv) 由于非 Garmin v) 未经 Garmin iv) 连接非 Garmin Garmin Garmin 90 90 1 Garmin Garmin Garmin Garmin RMA Garmin Garmin Garmin Garmin Garmin www.garmin.com/ support / warranty .html Garmin Marine Warranty Policy 20
?Declaration of Conformity
Page 1
...: Page: 1 of 1 DECLARATION of CONFORMITY Application of Equipment: Marine Sonar Transducer Model Number(s): Panoptix PS30 Panoptix PS31 The undersigned does hereby declare that the equipment complies with the above Directives Jamie Wiltshire Quality Supervisor Garmin (Europe) Ltd. General requirements Manufactured by: Manufacturer's Address: GARMIN International & 1200 E. 151st Street Olathe, Kansas 66062 U.S.A GARMIN Corporation No.68, Zhangshu 2nd Rd.., Xizhi Dist...
...: Page: 1 of 1 DECLARATION of CONFORMITY Application of Equipment: Marine Sonar Transducer Model Number(s): Panoptix PS30 Panoptix PS31 The undersigned does hereby declare that the equipment complies with the above Directives Jamie Wiltshire Quality Supervisor Garmin (Europe) Ltd. General requirements Manufactured by: Manufacturer's Address: GARMIN International & 1200 E. 151st Street Olathe, Kansas 66062 U.S.A GARMIN Corporation No.68, Zhangshu 2nd Rd.., Xizhi Dist...
Installation Instructions
Page 1
...8226; For a forward-facing transducer mounted on the computer. 2 Go to www.garmin.com/support/software/marine.html. 3 Select Download next to "Garmin Marine Network with SD card". 4 ...cables should not be mounted in a location where it on -screen instructions. 4 Wait several minutes while the software update process completes. CAUTION Failure to http://my.garmin.com. • Keep the original sales receipt, or a photocopy, in a safe place. Panoptix™ PS 30/31 Installation Instructions Important Safety Information WARNING See the Important Safety and Product Information guide...
...8226; For a forward-facing transducer mounted on the computer. 2 Go to www.garmin.com/support/software/marine.html. 3 Select Download next to "Garmin Marine Network with SD card". 4 ...cables should not be mounted in a location where it on -screen instructions. 4 Wait several minutes while the software update process completes. CAUTION Failure to http://my.garmin.com. • Keep the original sales receipt, or a photocopy, in a safe place. Panoptix™ PS 30/31 Installation Instructions Important Safety Information WARNING See the Important Safety and Product Information guide...
Installation Instructions
Page 2
... cable should mount the transducer at the mounting spot to lessen the pressure on the mounting screws. 5 If possible, route the cables to come out the port side, you have installed on your boat. TIP: On boats with thinner hulls, you can be routed close to the center line of electrical interference. When the Use AHRS setting is turned off...
... cable should mount the transducer at the mounting spot to lessen the pressure on the mounting screws. 5 If possible, route the cables to come out the port side, you have installed on your boat. TIP: On boats with thinner hulls, you can be routed close to the center line of electrical interference. When the Use AHRS setting is turned off...
Installation Instructions
Page 3
... a Garmin dealer if cutting the cables is necessary. 6 Add cable wraps to secure the cable, and provide a circular service loop to allow the trolling motor to rotate. 7 Route the power cable to 158°F). Assembling the Trolling-Mount Hardware 1 Attach the transducer mount bracket to the transducer À Á using the included 7 mm M4 mounting screws and M4 lock  washers . à 2 Attach the transducer mount bracket...
... a Garmin dealer if cutting the cables is necessary. 6 Add cable wraps to secure the cable, and provide a circular service loop to allow the trolling motor to rotate. 7 Route the power cable to 158°F). Assembling the Trolling-Mount Hardware 1 Attach the transducer mount bracket to the transducer À Á using the included 7 mm M4 mounting screws and M4 lock  washers . à 2 Attach the transducer mount bracket...
Installation Instructions
Page 4
or its subsidiaries www.garmin.com/support These trademarks may not be used without the express permission of Garmin Ltd. Garmin® and the Garmin logo are trademarks of Garmin. © 2015 Garmin Ltd. Panoptix™ is a trademark of Garmin Ltd. or its subsidiaries. or its subsidiaries, registered in the USA and other countries.
or its subsidiaries www.garmin.com/support These trademarks may not be used without the express permission of Garmin Ltd. Garmin® and the Garmin logo are trademarks of Garmin. © 2015 Garmin Ltd. Panoptix™ is a trademark of Garmin Ltd. or its subsidiaries. or its subsidiaries, registered in the USA and other countries.