Harbor Freight Tools 61613 - Electric Chain Saw Sharpener Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 61613 manuals!
Problems with Harbor Freight Tools 61613?
Ask a Question
Free Harbor Freight Tools 61613 manuals!
Problems with Harbor Freight Tools 61613?
Ask a Question
Harbor Freight Tools 61613 Videos
Harbor Freight Chainsaw Sharpener How To & Review 61613 63804 68221
Duration: 16:06
Total Views: 6,851
Duration: 16:06
Total Views: 6,851
Popular Harbor Freight Tools 61613 Manual Pages
User Manual - Page 2
.... DON'T FORCE TOOL.
Addresses practices not related to rain. Save all warnings and instructions for which , if not avoided, will do a job for future reference.
1. Cluttered...instructions may result in minor or moderate injury. Form habit of Contents
Safety 2 Specifications 5 Setup 6 Operation 8
Maintenance 10 Parts List and Diagram 14 Warranty 16
SAFETy
SETUp...
User Manual - Page 3
...part that it will operate properly and perform its operation. It's safer than using an extension cord, be properly repaired or replaced...Consult the owner's manual for best and...instructions for alignment of moving parts, binding of moving parts. The use of parts...off position before servicing; Wear protective hair...LEAVE TOOL RUNNING UNATTENDED. SETUp
OpERATION
MAINTENANCE
Item 61613...
User Manual - Page 4
...install the proper outlet. DO NOT OpERATE WITH ANy GUARD DISABLED, DAMAGED, OR REMOVED. Use grinding wheel suitable for a replacement.
22. Always use .
14. Double insulated tools may be present.
4. The use common sense when operating a power tool. Only use for 2-prong plug.)
Grinder Tool Safety Warnings
For your Own Safety Read Instruction Manual...specifically designed for the specific ...
User Manual - Page 5
...SETUp... (California Health & Safety Code § 25249.5, et ... supply to ensure medical problems are : • ...Specifications
Electrical Rating Motor No Load Speed Saw Chain Pitch Arbor Size Vise Capacity Max. WARNING: Handling the cord on how often you to lead, a chemical known to the hands, arms and shoulders. The warnings, precautions, and instructions discussed in this instruction manual...
User Manual - Page 6
... up or use of this manual including all text under Specifications on the bottom of the surface.
2. SAFETy
SETUp
Setup - TO pREVENT SERIOUS INJURy ...parts listed in the following pages, refer to the Assembly Diagram near the end of the tool off and unplug the tool from its electrical outlet before set up against the vertical edge of the Vise assembly through the hole in this manual...
User Manual - Page 7
Functions
Vise Handle
Depth Adjustment
Knob
Depth Adjustment
Lock Nut
SAFETy
SETUp
OpERATION
Handle
Vise Cable power Switch
Chain Stop Adjustment
Knob
Depth Adjustment
plate
Depth Adjustment
Stop
Chain Stop
Clamp plate
Vise
Safety Guard
Chain Stop ...
User Manual - Page 8
Installing the Grinding Wheel
...8226; rated to at a point 45° from the edge of this product. Replace the Grinding Wheel Cover.
TO pREVENT SERIOUS INJURy: DO NOT OpERATE WITH ANy GUARD...spindle.
6. SAFETy
SETUp
Operating Instructions
Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of...
User Manual - Page 9
...cutter is in the Sharpener and turn off the Sharpener, then unplug it.
6. Follow instructions for sparks and debris that will fly off before reinstalling it on the Handle until ...cord to the right of the Chain Wheels. Tighten the Depth Adjustment Lock Nut.
SAFETy
SETUp
Workpiece and Work Area Set Up
1. Unplug the Sharpener.
2. Tighten the Chain Stop Lock Nut.
• ...
User Manual - Page 10
... using dry compressed air.
4. If the supply cord of this manual must not be performed only by a qualified service technician. Store accessories in shelves, racks, boxes, or drawers.
Handle accessories carefully to prevent dropping or bumping. SAFETy
Maintenance and Servicing
procedures not specifically explained in this power tool is damaged, it has worn down...
User Manual - Page 11
...SAFETy
Troubleshooting
problem
possible Causes
Tool will not start. 1.
Wear ANSI-approved safety goggles and NIOSH-approved dust mask/respirator while blowing dust out of extension cord. Carbon brushes worn or damaged. 1.
Blocked motor housing vents.
4. Replace as needed .
2. Performance decreases over time. No power at outlet. Disconnect power supply before service...
User Manual - Page 12
... AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. pLEASE READ THE FOLLOWING CAREFULLy
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.
NEITHER THE MANUFACTURER OR...
User Manual - Page 13
Record product's Serial Number Here: Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Page 13
SAFETy
SETUp
OpERATION
MAINTENANCE
Item 61613
For technical questions, please call 1-888-866-5797.
User Manual - Page 14
...
24 Pin
25 Circlip
Qty.
3 1 1 1 1 11 2 1 2 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2
part
Description
26 Base
27 Vise Base
28 Chain Stop
29 Washer
30 Screw
31 Shaft
32 Swing Arm
33 Washer
34 Torsion Spring
35 Nut... Bolt
49 Angle Adjusment Knob
Qty.
1 1 1 1 4 1 1 5 1 1 2 1 1 1 2 2 1 2 1 2 2
1 1 1
SETUp
OpERATION
MAINTENANCE
Page 14
For technical questions, please call 1-888-866-5797.
User Manual - Page 15
Assembly Diagram
SAFETy
SETUp
OpERATION
MAINTENANCE
Item 61613
For technical questions, please call 1-888-866-5797. Page 15
User Manual - Page 16
..., repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of the complaint must accompany the merchandise. This warranty gives you specific legal...will either repair or replace the product at our expense, but if we determine there is free from defects in no defect, or that this warranty, the product or part must bear ...
Harbor Freight Tools 61613 Reviews
We have not received any reviews for Harbor Freight Tools yet.