Harbor Freight Tools 62523 - 2000 Peak/1600 Running Watts Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
This item is in your list!
View All Support Options Below
Free Harbor Freight Tools 62523 manuals!
Problems with Harbor Freight Tools 62523?
Ask a Question
Free Harbor Freight Tools 62523 manuals!
Problems with Harbor Freight Tools 62523?
Ask a Question
Popular Harbor Freight Tools 62523 Manual Pages
User Manual - Page 1
...reproduced in any parts are open. Tools required for assembly and service may be included.
Failure to continuing improvements, actual product may not be drawn proportionally. SAVE THIS MANUAL. Generator exhaust contains carbon monoxide. Copyright© 2015 by Harbor Freight Tools®. Owner's Manual & Safety Instructions
Save This Manual Keep this manual and the receipt...
User Manual - Page 2
... pages of Contents
Specifications 2 Safety 3 Setup 7 Operationr 8
Maintenances 13 Troubleshooting 18 Parts List and Diagram 20 Warranties 22
Specifications
Generator
Output
Receptacles
...2
For technical questions, please call 1-888-866-5797. ITEM 62523 Table of this Engine is warranted for this manual. oz.
6 hr.
66 dB 48.6mm x 43mm A5RTC (Torch) or equivalent 0.023" - 0.027"...
User Manual - Page 3
...personal injury. Read the manual before set-up and/or use.
WARNING marking concerning Risk of Hearing Loss. Do not refuel while operating.
SAVE THESE INSTRUCTIONS
Operation
Maintenance
ITEM 62523
... OUTSIDE and far away from engine.
IMPORTANT SAFETY INSTRUCTIONS
WARNING! It must be understood by the operator. Safety
Setup
WARNING SYMBOLS AND DEFINITIONS This is used to alert...
User Manual - Page 4
... in the Specifications chart of this...codes.
7. Faulty appliances or power cords can allow electrical current from building up power.
10. Safety
Setup
Setup Precautions
1. A spark arrestor may create sparks that of the product to be powered to the instruction manual...it can be installed by a portable ...set up in accordance with all relevant local, state, and federal electrical codes...
User Manual - Page 5
...., in accordance with these instructions and in the presence of...parts. Do not modify the equipment and do not use , check for your model...parts, breakage of equipment, taking into account the working nearby while it is operating.
24. If damaged, have the equipment serviced...
Setup
Operating Precautions (cont.)
13. Connect...harm. (California Health & Safety Code § 25249.5, et seq.)
39. Do not...
User Manual - Page 6
...by a qualified repair person using a...THESE INSTRUCTIONS.
Keep all safety guards in place and in this manual or any procedures that may adjust parts that...service technician may increase or decrease governed engine speed.
5. Only connect two identical Inverter Generators together using only identical replacement parts.
Do not fill fuel tank to expand as needed.
4. c. d. Safety
Setup...
User Manual - Page 7
... IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all relevant electrical codes and standards before set up or use and to prevent damage to allow efficient high-altitude use of this equipment may be properly grounded in accordance with this product. Safety
Setup
Operation
TO PREVENT SERIOUS INJURY AND FIRE: Operate...
User Manual - Page 8
...any problems are ... Then replace the ...parts before adding fuel. Do not smoke.
1. Add fuel stabilizer to evaporate before set... up to about 1 inch under subheadings therein before starting . To prevent FIRE, do not use equipment until the oil level is hot from ignition sources. ITEM 62523 If any dirt and debris. If the Engine is at the beginning of this manual...Setup
Operation
Maintenance...
User Manual - Page 13
...manual, will differ depending on factors such as a general guide. Clean fuel tank, strainer
and carburetor 4. of use
Every 3 mo.
Every 2 Years
** **
Operation
Maintenance
ITEM 62523
For technical questions, please call 1-888-866-5797. Follow all service instructions in addition to safely service the equipment or engine, have the problem...engine oil Clean/replace air cleaner Check...
User Manual - Page 14
...Plug back in the air.
Clean the Fuel Cap and the area around it counterclockwise.
5. Then replace the Fuel Cap.
6.
Tilt the Generator over an oil drain pan. Recycle used oil.
6.
....
4. Remove the Oil Fill Plug, turning it . Safety
Setup
Checking and Filling Fuel
WARNING! If the engine is VOID. Set the Generator back down on Gas Cap. The oil level should...
User Manual - Page 18
.../ repair ignition system.
COMPRESSION RELATED:
1. If that does not work, replace spark... all safety precautions whenever diagnosing or servicing the generator or engine. IGNITION (SPARK) ...Setup
Troubleshooting
Problem Engine will not start again.
2. Incorrect spark timing or
faulty ignition system. Turn Choke to start
Possible Causes
Probable Solutions
FUEL RELATED: 1. Replace...
User Manual - Page 19
...Check engine timing.
Device not plugged in properly.
1. Device not plugged in properly.
1. Immediately unplug device.
Safety
Setup
Problem
Possible Causes
Probable Solutions
Engine misfires
1. Re-gap or replace spark plug.
3. Defective spark plug cap.
3. Replace spark plug cap.
4. Old or low quality gasoline.
4. Use only fresh 87+ octane stabilizer-treated unleaded...
User Manual - Page 20
...., Fuel
1
16 Jaw Nut
6
50 Support, Invertor
1
84 Nut
1
17 Cushion,... Band
2 101 Screw
4
34 Guide, Starting Rope
1
68 Nut
4...REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. Safety
Setup
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LISTS AND ASSEMBLY DIAGRAMS IN THIS MANUAL...
User Manual - Page 22
... consequential damages, so the above .
HFT must warrant that HFT may include parts such as the problem exists in addition to obtain warranty repair or replacement, by HFT. Your emissions control system may deny you warranty coverage if your engine will repair or replace, at our option, your warranty coverage, you .
The nearest Harbor Freight Tools...
User Manual - Page 23
... Items Used in the written instructions is two years. Evaporative Emission Control System a. b. Safety
Setup
GENERAL EMISSIONS WARRANTY COVERAGE
a) The warranty period begins on the date the engine or equipment is as follows:
1. If any warranted part under the warranty will be repaired or replaced by contacting HFT product support at 1-888-866-5797 or productsupport...
Harbor Freight Tools 62523 Reviews
Do you have an experience with the Harbor Freight Tools 62523 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Harbor Freight Tools yet.
Earn 750 points for your review!