Harbor Freight Tools 97009 - 1 HP 7in. x 12in. Hydraulic Feed Metal Cutting Band Saw Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 97009 manuals!
Problems with Harbor Freight Tools 97009?
Ask a Question
Free Harbor Freight Tools 97009 manuals!
Problems with Harbor Freight Tools 97009?
Ask a Question
Popular Harbor Freight Tools 97009 Manual Pages
User Manual - Page 1
....com
Read this material before using this manual.
For technical questions or replacement parts, please call 1-800-444-3353. Failure...manual or any artwork contained herein may be drawn proportionally. All rights reserved.
Distributed exclusively by Harbor Freight Tools®. METAL CUTTING BANDSAW 7" X 12"
Model 97009
Set up And Operating Instructions
Diagrams within this manual...
User Manual - Page 2
Page
TABLE OF contents
Important Safety Information 3 General Safety Rules 4 Specific Safety Rules 6 Grounding 8 Extension Cords 9 Symbology 10 Product Specifications 10 Set Up Instructions 11 Operating Instructions 12 Maintenance and Servicing 25 Troubleshooting Guide 29 Parts Lists 30 Assembly Diagrams 38 Electrical Schematics 43 Warranty Information 46
SKU 97009
For ...
User Manual - Page 6
... Blade Guide Arm ... to cut .
1.
Specific Safety Rules
1. SKU ...supported. Before using the Bandsaw, check to prevent the Bandsaw from accidentally moving parts... of the workpiece to be cut . Make sure the Table of the Bandsaw and surrounding area are clear with the exception of the Bandsaw while it .
11. If unreadable or missing, contact Harbor Freight Tools for a replacement...
User Manual - Page 7
...instruction manual cannot cover all possible conditions and situations that common sense and caution are : Lead from lead-based paints Crystalline silica from bricks and cement or other practical ways to secure and support...microscopic particles. (California Health & Safety Code § 25249.5, et seq.)
...your industrial coolant supplier for specific coolant recommendations when cutting magnesium....
User Manual - Page 11
... assistance and a proper lifting device.
2. Set Up Instructions
Read the entire Important Safety Information section at the bottom/right side of this manual as soon as possible.
WARNING
Risk of this...at the number shown on each end of this manual including all text under subheadings therein before assembling or making any parts are unpacked, make sure its Head is lowered...
User Manual - Page 12
... a quick action Vise Jaw mechanism which allows you to operate on a grounded, 120 volt system. Operating Instructions
Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of the Stand (77S). (See Figure B.)
. TO USE THE QUICK VISE
1. Screw...
User Manual - Page 14
...the small rectangular opening across the Base (1). • Attach Screws (A and B). Align the lower edge of pre-set lengths
1. Tighten the screws. (See Figure F) FIGURE F
A
D
B
TO ADJUST THE STOP BLOCK
For ... cuts of the Rear Vise Jaw (22) with the "0" index mark adjacent to the 16° degree setting. Adjust the Stop Block (41) to the Stock Stop Rod (40). (See Figure G)
2.
Loosen the...
User Manual - Page 16
The illustration below shows several settings for several types of materials. (See Figure K.)
Material
Stainless Alloy Steels Bearing...266-7), and remove the Deflector Plate (266-3). (See Figure I.)
DEFLECTOR PLATE (266-3)
SAW BLADE (251)
FIGURE I
SCREWS (266-7)
4. Guide the Saw Blade (251) through the slot in the Vertical Saw Table (55-2), and secure it in position with the two Screws (266...
User Manual - Page 18
...8226; The Blade Guide Bearings (266-10) are mounted to the Guide Pivot Assemblies (270S) and can be rubbing against the flange. (See Figure O, next page.)
3.
A Saw Blade replacement will begin cutting ...4. If a new Saw Blade (251) does not correct the problem, check the clearance between the Saw Blade and Blade Guide Bearing. Page 18
The Saw Blade (251) is tracking properly when...
User Manual - Page 20
...coolant supplier for specific coolant recommendations when...water-soluble coolant (not included). (See Figure R.)
4.
TO ADJUST THE BLADE GUIDE BRACKETS
1. Once the adjustment is adjusted by loosening the Knob and sliding the... should be set as close as possible to about 80% capacity with the workpiece. (See Figure Q.)
3. IMPORTANT: The water-soluble coolant should be replaced as often ...
User Manual - Page 21
...approved safety impact eye goggles when operating the Bandsaw. Page 21 VERTICAL POSITION
1. If this manual) have been made.
• Cut only flat workpieces when the Bandsaw is in this is...
3. Check to its vertical position.
• Before cutting, turn off the Bandsaw and correct the problem before using.
• Always keep the Bandsaw Blade enclosure closed.
• Do not plug the Power...
User Manual - Page 22
... MOTOR TOGGLE SWITCH (750S4)
SAW HEAD ASSY. Turn the Motor Toggle Switch (750S4) to its "ON" position. (See Figure S.)
7. Set the workpiece on the workpiece throughout the cutting process. (See Figure S.)
. Turn the Coolant Pump Fitting (91S) to keep downward pressure on... position. (See Figure S.)
. Do not force the Bandsaw to remove material faster than it is properly supported.
User Manual - Page 23
...problem...to lock the Saw Head Assembly in the moving parts of an uncompleted cut is plugged in and running....
4. HORIZONTAL POSITION
1. Never attempt to lock the Saw Head in this manual) have been made , turn the Cylinder to its entire length is to...this is found, turn off the Bandsaw if the workpiece is properly supported. Secure the workpiece in their "OFF" positions. (See Figure ...
User Manual - Page 25
... (See Figure T.)
Maintenance And Servicing
WARNING
Risk of moving parts, cracked or broken parts, damaged electrical wiring, and any..." position. If abnormal noise or vibration occurs, have the problem corrected before performing any other condition that may affect its electrical... the general condition of the Bandsaw. (See Figure T.)
1. Replace with a new Saw Blade when needed. 13. Once the ...
User Manual - Page 28
..., use only a clean cloth and mild detergent or mild solvent to the original product or replacement parts thereto, or arising out of his or her installation of the machine in liquid.
. All maintenance, service, and repairs not mentioned in this manual must only be undertaken by certified and licensed technicians, and not by a qualified technician. In...
Harbor Freight Tools 97009 Reviews
We have not received any reviews for Harbor Freight Tools yet.