Hayward HP21404TC Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward HP21404TC manuals!
Problems with Hayward HP21404TC?
Ask a Question
Free Hayward HP21404TC manuals!
Problems with Hayward HP21404TC?
Ask a Question
Popular Hayward HP21404TC Manual Pages
LITHTPRO23_HeatPro_Series_Sell_Sheet_DIGITAL_5b7e - Page 2
...MODEL NUMBER
Low Ambient Operation
BTU HEATING PERFORMANCE
80°F Ambient Air, 80°F Water, 80% Relative Humidity* 80°F Ambient Air, 80°F Water, 63% Relative Humidity* 50°F Ambient Air, 80°F Water, 63% Relative Humidity*
HEAT Operating Temperature °F
HP21004T HP21124T
No
No
HP21254T
No
HP21404T
No
HP21104TC
HP21404TC...187; hayward.com » 1-800-HAYWARD
Pumps...
HeatPro_Square_Manual_Rev_G_5148 - Page 1
...CHECK-OUT & START-UP
17
United States and the Canadian Electric Code
CONTROL SETUP
18
(CEC) in pool/spa heater
WINTERIZATION
24
installation. TROUBLESHOOTING
26
PARTS
29
SAVE THESE INSTRUCTIONS
USE ONLY GENUINE REPLACEMENT PARTS
1 51300003301G
IN GROUND POOL/SPA HEAT PUMP HEATERS INSTALLATION & OPERATIONS MANUAL
FOR YOUR SAFETY
CONTENTS
Pg. This Heat Pump is listed by
WATER...
HeatPro_Square_Manual_Rev_G_5148 - Page 8
...in this manual and on this product. WARNING -
WARNING - Body Suction Entrapment-
o Installation of access ...frequently and
replaced at all local and state codes and with latest ASME, APSP Standards and
CPSC guidelines, follow instructions can result... so as a means of the installing site. Canadian Electrical Code, Part I
CONFORMANCE WITH CODES: The heater shall be damaged, ...
HeatPro_Square_Manual_Rev_G_5148 - Page 9
...REPLACEMENT PARTS
9 Failure to follow safety and operation instructions...servicing pool and spa water circulation system, all system valves must be set in conformance with compressed air. Before starting system pump, all system and pump controls must be in off position and filter manual.... Risk of electric shock, see installation instructions and consult a professional electrician on ...
HeatPro_Square_Manual_Rev_G_5148 - Page 13
...installed on the outlet line of anchoring screws when required by the evaporator coil when the unit is for use the
following; Follow all
relevant Local, State and National requirements regarding wind load anchoring. Failure to be produced by local codes. USE ONLY GENUINE REPLACEMENT PARTS... air temperature and humidity. Once the manual bypass valve is required to prevent accidental...
HeatPro_Square_Manual_Rev_G_5148 - Page 15
... the heat pump from the heat pump CONSUMER KIT adjacent to the unit to facilitate easy service procedures
51300003301G Figure7: Heater Installation Above Pool
Figure8: Typical Plumbing to LOCATING THE HEATER section for proper pressure switch setup. Maintain 4-6ft [1,2-1,8 m] clearance
between the units, 2ft [0,6 m] around perimeter, and at least 6ft [1,8 m] over them. the...
HeatPro_Square_Manual_Rev_G_5148 - Page 17
...
Figure12: Remote On/Off Control
CHECK-OUT & START-UP
GENERAL: After completing the installation connections to the pool heater, follow the procedures outlined below to starting the heater. ...the water temperature set point control at the heater, press and hold both the "MENU" and the "+" buttons until "bo" appears. USE ONLY GENUINE REPLACEMENT PARTS
17 Heat Only models connect the ...
HeatPro_Square_Manual_Rev_G_5148 - Page 18
... the cycle. CONTROL SETUP HEAT/COOL MODELS
This pool heater is equipped with a digital thermostat which mode is currently active. Use the set button in Figure14a to maintain the desired temperature. The arrows will automatically function to high-pressure sub cooled liquid (A), which mode is currently active.
18
USE ONLY GENUINE REPLACEMENT PARTS HEAT: in...
HeatPro_Square_Manual_Rev_G_5148 - Page 20
...settings to confirm call for five seconds, and will then return to Performance Monitoring / Troubleshooting...error condition is displayed. DUAL POOL AND SPA SET...set Pool temperature set point as shown in order for spa mode (max: 104°F/40°C). Check TROUBLE... switch c. The minimum allowed settings for service
20
USE ONLY GENUINE REPLACEMENT PARTS
Then use the (Plus) ...
HeatPro_Square_Manual_Rev_G_5148 - Page 22
...set temperature settings, Heating
("HE"), Cooling ("COL") and Automatic ("AUt"). b. Check TROUBLE SHOOTING SECTION in this manual or Call for heating/cooling. To
change , refer to Performance Monitoring / Troubleshooting section in this manual...an error condition is best not to try and set the maximum heating below the set point a call for service
22
USE ONLY GENUINE REPLACEMENT PARTS
...
HeatPro_Square_Manual_Rev_G_5148 - Page 23
... the
USE ONLY GENUINE REPLACEMENT PARTS
23 If heater has been... at least the rated minimum (see SPECIFICATION SECTION). 3. Failure to maintain proper ...heater. 4. Keep this manual with Heater below the ...installation, checkout, and start , adjust the pressure switch by a qualified service technician. The following procedure is recommended when the switch needs adjustment and/or is replaced...
HeatPro_Square_Manual_Rev_G_5148 - Page 24
...must be installed between the heater and chlorinator to avoid freeze-up in the specifications section.
...MANUAL. SKIMMER CHLORINATION Placing chlorine or bromine Tablets directly into the water is NOT covered under the manufactures warranty.
24
USE ONLY GENUINE REPLACEMENT PARTS... the heat exchanger is also advantageous for service needs and for proper low-flow protection....
HeatPro_Square_Manual_Rev_G_5148 - Page 25
... heater has been
under water. Set the temperature control using valves, then perform draining the heat exchanger.
1. Check with heater related troubleshooting tips, be certain that a PERIODIC INSPECTION also be performed annually to repair broken or faulty components of the display keypad/control board and the terminal board. Replace any manner. THERMISTOR: The thermistor...
HeatPro_Square_Manual_Rev_G_5148 - Page 27
... HP
Table 5: Display Code Index
Problem No power to heat pump...installed.
Clean your filter Make sure all valves are fully open and bypass valve is closed
Turn off fountains, etc. Check pool temp. Unit is on . Call for service. Wait until pool needs heat. Clean your filter Make sure all valves are fully open . Call for service. USE ONLY GENUINE REPLACEMENT PARTS...
HeatPro_Square_Manual_Rev_G_5148 - Page 28
...
USE ONLY GENUINE REPLACEMENT PARTS
Turn thermostat down Clean it by running continually?) If heat pump continues to cycle, turn unit off to prevent compressor damage. Heat pump is running but leave the filter pump running
Low water flow
Outside temperature too low
Make sure power is on . Thermostat set too high
Evaporator...
Hayward HP21404TC Reviews
We have not received any reviews for Hayward yet.