Hayward OmniHub Smart Pool and Spa Control Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward OmniHub Smart Pool and Spa Control manuals!
Problems with Hayward OmniHub Smart Pool and Spa Control?
Ask a Question
Free Hayward OmniHub Smart Pool and Spa Control manuals!
Problems with Hayward OmniHub Smart Pool and Spa Control?
Ask a Question
Popular Hayward OmniHub Smart Pool and Spa Control Manual Pages
Omnihub Installation Manual - Page 5
HL-CHEM
ORP & pH Sensing Kit for ORP control (requires additional equipment) • controls an optional Hayward Aqua Rite salt chlorinator. You can now conveniently monitor your pool/spa and change settings anytime, and from Hayward. A Quick Start guide may have a HLAQRPCB communication board installed
Optional accessories (page 3) can expand the functionality of water applications only)...
Omnihub Installation Manual - Page 6
..., not from the Wiring Hub to install the OmniHub, familiarize yourself with a 15 ft cord. A separate remote control connection is required if using chemistry Sense and Dispense accessories.
For solar heating systems, a solar sensor is also required. Overview
Before attempting to the heater.
5
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Input power should be connected to...
Omnihub Installation Manual - Page 9
... wiring will be able to get a snug fit.
8
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
When considering the mounting location, make sure there is enough clearance above the enclosure so that the flip door will be opened fully. Tighten until the bottom of 6 ft (2 meters) horizontal distance from the pool/spa (or more, if local codes require).
Omnihub Installation Manual - Page 18
...the relay can be manually controlled using the On/...supported by Universal ColorLogic lights built
after June 2018.
17 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Powering a 230 VAC Two Speed Pump
A 230 VAC two speed pump requires the use the On/Off button manually while the Off or Green Smart Relay is being automatically controlled by Wiring Hub
(not allowed)
Blinking
Blinking
Firmware upgrade...
Omnihub Installation Manual - Page 20
... cable types and splices.
19
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Up to OFF position. If a longer ...set all dipswitches
to three Smart Relays can control up to the same connector as shown below.
Their 4 conductor cable is
wired to two valve actuators which allow automated control of pool/spa, water features, cleaners or solar heating and is required, contact the Hayward service...
Omnihub Installation Manual - Page 21
.../off external device provides a means to receive the wire lead. Pool/Spa Sensor
Push on lever
Insert wire here
Air Sensor
Optional Solar Sensor or
External Input Switch
External Input Switch
If solar heating won't be used for firmware upgrades.
20
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
This
normally open and able to turn the filter pump...
Omnihub Installation Manual - Page 24
....
23 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS There may advise you to the Wiring Hub. Also, if you have experienced problems, Hayward Technical Support may be done before or after Configuration but should be a newer version available and if so, we encourage you to the OmniHub. To upgrade the OmniHub firmware, refer to fully start. Upgrading firmware can be used...
Omnihub Installation Manual - Page 48
... than Temperature °C/F, Equipment will be off . Pressing any of these buttons will be controlled independently.
If the temp sensor reads less than Temperature °C/F, Equipment is lower than the setting, the Equipment can be forced
47
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Equipment is always on when the sensor temperature is higher than the...
Omnihub Installation Manual - Page 49
...when not in the selected mode. Equipment is not [Pool/Spa/Spillover], Equipment will be controlled independently - Equipment cannot be off and prevented from ...Pool/Spa/Spillover], then Equipment will be off and prevented from turning on . Pressing any of the possible selections that your configuration settings and restart the OmniHub.
48
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS...
Omnihub Installation Manual - Page 63
... service centers please contact the Hayward Technical Service Support Center (61 Whitecap Road, North Kingstown RI, 02852) or visit the Hayward web site at www.hayward.com. WARRANTY EXCLUSIONS: 1. In no event shall Hayward Pool products be responsible for cartage, removal, repair or installation labor or any other such costs incurred in obtaining warranty replacements or repair. Hayward...
Omnihub Operational Manual - Page 2
... excess of the pool, spa or hot tub shall be bonded to the equipment grounding bus with a continuous copper wire equivalent in size to the circuit conductors supplying the equipment. • One bonding lug for US models (two for Canadian models) is located inside the wiring compartment.
SAVE THESE INSTRUCTIONS
1 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS To
reduce...
Omnihub Operational Manual - Page 8
...Spa in which will bring you to turn on/off . Touch this switch manually to select a speed based on /off the pump.
ON
ON
LOW
MED
POOL vsp pump
HIGH CUSTOM
Set Schedule - All of the equipment shown in the Features Screen for the Pool only. Control... ONLY HAYWARD GENUINE REPLACEMENT PARTS
Countdown Timer - Diagnostics - This option only appears for single speed pumps.
Omnihub Operational Manual - Page 16
... the cell after cleaning your filter.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS If you restart average salt, the previous average is higher than the pool/spa water temperature displayed on an ongoing calculated average.
NOTE: If a conventional or solar heater is operating, it is only available in Service Mode. The OmniHub periodically reverses the polarity of...
Omnihub Operational Manual - Page 32
... Upgrading Firmware (must be in Service Mode, page 3)
1. Insert your USB thumb drive into your USB thumb drive. Remove the USB thumb drive from the website and then touch the Save button.
...\
USB/ MSP_AR_BO140017
select le
...\
select le
USB/
MSP_AR_BO140017
FILE selection
FILE selection
31 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Enter Service Mode (page 3) 8. Touch the Upgrade...
Omnihub Operational Manual - Page 39
... of one (1) year. Problems resulting from tampering, accident, abuse, negligence, unauthorized repairs or alternations, fire, flood, lightning, freezing, external water, degradation of natural stone used in or immediately adjacent to a pool or spa, war or acts of any other rights, which vary from state to state.
38 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS The express limited warranty...
Hayward OmniHub Smart Pool and Spa Control Reviews
We have not received any reviews for Hayward yet.