Hayward PL-P-4 Support and Manuals
Get Help and Manuals for this Hayward item
View All Support Options Below
Free Hayward PL-P-4 manuals!
Problems with Hayward PL-P-4?
Ask a Question
Free Hayward PL-P-4 manuals!
Problems with Hayward PL-P-4?
Ask a Question
Popular Hayward PL-P-4 Manual Pages
Operation Manual - Page 1
Automation and Chlorination
Operation Manual
for models
PL-P4-SWP
www.haywardnet.com
Operation Manual - Page 2
... AND FOLLOW ALL INSTRUCTIONS
•
! IMPORTANT SAFETY INSTRUCTIONS
When using this product unless they are closely supervised at all AC power during installation.
•
! To reduce the risk of injury, do not permit children to the circuit conductors supplying the equipment.
• One bonding lug for US models (two for Canadian models) is located inside...
Operation Manual - Page 4
... system setup are available.
The Swimpure Plus with Controls that the SwimPure Plus with Controls can control pumps, valves, lighting, heaters, and chlorination. The only time you may need to add sanitizing chemicals to your pool/spa system.
The SwimPure Plus with Controls has been wired and configured according to the Installation Manual...
Operation Manual - Page 7
... threshold. Pressing the POOL/SPA button will return the SwimPure Plus with Controls to switch to service-timed mode which was set up in this mode of operation until manually taken out of service mode.
Pressing the SERVICE button again will cause the SwimPure Plus with Controls to turn off while the pool/spa valves...
Operation Manual - Page 10
... the system has been setup for the service technician and contains information and details about the system operation that will turn on whenever the pool/spa valves are part of the Timers Menu...menus you have both the Operation and the Installation Manual.
This menu is a series of your pool. The SwimPure Plus with nothing to set all system operating parameters except the timeclock ...
Operation Manual - Page 20
... by a pump, then one of the AUX relays must be setup for 2-speed operation. Also, the "solar" temperature sensor must be set up for the first 3 minutes after solar heat turns on the...next menu item or previous/next configuration menu
Solar If the solar control logic is "Enabled", several additional steps must be installed. If the solar is operated by a valve, then the Valve3 output...
Operation Manual - Page 34
... attention for optimal operation of your pool. Clean the cell (see instructions, page 30) and then press the "+" button during servicing of the pool equipment. The SwimPure Plus with Controls will provide some detailed information regarding the operation, call the Hayward Technical Service Department from damage. The only way to lower the salt level...
Operation Manual - Page 39
... USE A REPLACEMENT CHLORINATOR CELL OTHER THAN AN UNMODIFIED, NEW HAYWARD/GOLDLINE CHLORINATOR CELL PURCHASED FROM HAYWARD/GOLDLINE. LIMITED WARRANTY (effective 04/01/09) Hayward/Goldline warrants its Pro Logic and E-Command pool automation products as well as its Aqua Trol chlorination products to be the sole determinant of the date of installation of the product.
Problems resulting from...
Installation Manual - Page 1
®
Installation Manual
for model
PL-P4-SWP
www.haywardnet.com
Installation Manual - Page 2
....
• A green colored terminal marked "Grounding" is provided on the external surface. IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying the equipment...
Installation Manual - Page 8
...specific installation information.
5 A solar sensor is required if the solar function is designed to the same sunlight as a heat sink (disperses heat from the pool/spa (or more, if local codes require).
Use additional cable (20 AWG) if necessary. Refer to the AQL-CHEM2 manual
for plumbing and wiring instructions...is suitable for specific installation information.
Temperature ...
Installation Manual - Page 19
... will be selected under "Set COMM bus address" (EcoStar) or "*H.Comm ADDR." (TriStar) within the
VSP's Configuration Menu. Pro Logic Output
This is entered into the VSP's configuration menu. EcoStar only
AUX2
Aux2 - Remove the jumper for each VSP used to heater. 2. Refer to the table below to your specific pump and SwimPure Plus...
Installation Manual - Page 27
... normally open or normally closed.
If applicable, the homeowner will be installed. When solar heat is configured for solar logic. Allow Low Speed This menu only appears if the pool filter is..., then the Valve3 output must be setup for 2-speed operation. In this menu, select the state of heating the pool. The selection is in the "Settings Menu". This sensor is typically mounted ...
Installation Manual - Page 34
...) then solar must be set to the heater manual and also "Heater Control" (...valve is installed, check that water is flowing through the heater. • The heater temperature setting is properly...set correctly for 3 hours, then automatically return to turn any output on as indicated by the "Heater" LED being illuminated. Heater Checkout
Follow these instructions to exit out of Service...
Installation Manual - Page 35
... WARRANTY (effective 04/01/09) Hayward/Goldline warrants its Pro Logic and E-Command pool automation products as well as its Aqua Trol chlorination products to be free of defects in materials and workmanship, under normal use and service for a period of one (1) year.
Problems resulting from tampering, accident, abuse, negligence, unauthorized repairs or alternations, fire, flood...
Hayward PL-P-4 Reviews
We have not received any reviews for Hayward yet.