HP EliteDesk 880 G3 Support and Manuals
Get Help and Manuals for this Hewlett-Packard item
View All Support Options Below
Free HP EliteDesk 880 G3 manuals!
Problems with HP EliteDesk 880 G3?
Ask a Question
Free HP EliteDesk 880 G3 manuals!
Problems with HP EliteDesk 880 G3?
Ask a Question
Popular HP EliteDesk 880 G3 Manual Pages
Getting Started Guide - Page 6
... system 22 Downloading Windows updates ...22 Customizing the monitor display ...22 Turning off the computer ...23 If you encounter issues ...23 Performing basic troubleshooting ...23 Visual inspection: No boot, no power, no video 23 Blink or beep codes: Interpreting POST diagnostic front panel LEDs and audible codes ...24 HP Support Assistant ...24 Using HP PC Hardware Diagnostics...
Getting Started Guide - Page 17
... to perform a System Recovery: ● Recovery image - Any personal files must choose one of information, be restored from support.
Follow the on-screen instructions to set from backups you made. Go to http://www.hp.com/support, select your backup. NOTE: You may take over an hour, depending on file size and the speed of...
Maintenance and Service Guide - Page 12
Refer to the Maintenance and Service Guide to interpret the code.
2 Chapter 1 Product features Some models have a bezel blank covering one or more drive bays. If it is on the power button is normally white when the power is displaying a diagnostic code.
Front panel components
1 5.25-inch half-height drive bay (behind bezel)
7 Audio-out (headphone...
Maintenance and Service Guide - Page 85
... Computer Setup (F10) Utility and the
settings described in this computer. ● Enable the power-on or restart the computer. 2. Turn on password prompt during system restarts (warm boots) as well as Secure Boot, power management, virtualization support, and language and
keyboard type used in the Computer Setup Utilities menu: Main, Security, Advanced, and UEFI Drivers.
Maintenance and Service Guide - Page 91
...factory defaults. Default is enabled. ● Network (PXE) Boot. Computer Setup-Advanced
NOTE: Support for Computer Setup. ● Fast Boot.
Default is to provide additional time to activate hotkeys such as power is attached to reset security settings during a service event.
Sets the drive's master password but does not enable DriveLock. Enable DriveLock. One purpose for...
Maintenance and Service Guide - Page 109
...
If the graphics controller was upgraded, the correct graphics drivers may be set properly. Replace the graphics card. Cause Position may be loaded.
Cause The monitor connections may be incomplete or the monitor may need adjustment.
Monitor does not function properly when used with the monitor for instructions.
Cables are not set . In a two-monitor system...
Maintenance and Service Guide - Page 117
... issue, contact Customer Support.
DIMM1 must be installed before DIMM2, and DIMM3 must be installed. Solving Network Problems
Some common causes and solutions for network problems are codes for the correct driver or obtain the latest driver from the list of debugging the network cabling. Check the network controller documentation for specific problems.
3. Solving Network Problems 107
Maintenance and Service Guide - Page 118
...installed. Check cabling and network equipment for link status. Network driver is attached to the correct connector.
The cable is not properly loaded. Contact an authorized service provider. Make sure the network drivers...is a problem with the network. Ensure that the cable is not set up ....
108 Chapter 6 Troubleshooting without diagnostics Reinstall network drivers.
Cause The cable ...
Maintenance and Service Guide - Page 125
Solving front panel component problems
If you encounter Internet access problems, consult your ISP for having the browser remember some specific information that the USB ports are set up properly. The correct device driver is not working.
1. If possible, replace the cable. 2. USB ports on the front of the computer and restart the computer.
Unable to connect...
Maintenance and Service Guide - Page 128
... basis.
Reset the date and time under Control Panel (Computer Setup can take to the Full Boot Every x Days mode, using Computer Setup. NOTE: For more information on Computer Setup, see if the problem remains.
4. Verify the correct ROM.
2. Replace the system board.
1. If a POST error occurs, the screen will beep once after a POST text message...
Maintenance and Service Guide - Page 129
The product information programmed into the system board is not supported by the BIOS. Recommended action
problem persists, replace the RTC battery. Upgrade BIOS to update this information.
1. If the error persists, replace the system board.
1. If the memory configuration was recently changed , unplug the power cord, restore the original memory configuration, and reboot the computer.
4....
Maintenance and Service Guide - Page 130
... on Unsupported Platform 2E6-Memory Not Configured Correctly for memory support information.
Verify proper memory module type.
3. Remove and replace the identified faulty memory module(s).
4. If the error persists after replacing memory modules, replace the system board.
Either the installed hardware has changed, storage or firmware mode may have failed to this feature).
If no...
Maintenance and Service Guide - Page 131
...disk drive. Reconfigure card resources and/or run Computer Setup or Windows utilities. Apply hard drive firmware patch if applicable. (Available at http://www.hp.com/support.)
Back up contents and replace hard drive. Hard drive is giving correct error message.
Hard disk 1 error.
1. Hard disk 2 error.
1. Clear CMOS. (See Password security and resetting CMOS on page 125.)
3. Both...
Hardware Reference Guide - Page 8
...one or more drive bays. Front panel components
Drive configuration may vary by model. Refer to the Maintenance and Service Guide to interpret the code.
2 Chapter 1 Product features If it is flashing red, there is a problem with HP Sleep and Charge
3 SD card reader (optional)
9 USB 2.0 port
4... it is on the power button is normally white when the power is displaying a diagnostic code.
Hardware Reference Guide - Page 19
... with up to the following specifications: ● Industry-standard 288...Upgrading system memory
The computer comes with two sockets per channel. Sockets DIMM3 and DIMM4 operate in memory channel B. Installing a memory module
There are populated in one preinstalled memory module. To achieve the maximum memory support, you install unsupported memory modules. The sockets are installed...
HP EliteDesk 880 G3 Reviews
We have not received any reviews for HP yet.