HP StorageWorks 1606 - Extension SAN Switch Support and Manuals
Get Help and Manuals for this Hewlett-Packard item
This item is in your list!
View All Support Options Below
Free HP StorageWorks 1606 manuals!
Problems with HP StorageWorks 1606?
Ask a Question
Free HP StorageWorks 1606 manuals!
Problems with HP StorageWorks 1606?
Ask a Question
Popular HP StorageWorks 1606 Manual Pages
HP StorageWorks SAN Switch rack mount kit installation instructions (A7511-90905, October 2009) - Page 1
... (MP) Router
Supported HP custom racks
Use the SAN Switch Rack Mount Kit with the following HP website: http://www.hp.com/support/manuals
Page 1 Supported devices
Use the SAN Switch Rack Mount Kit to rack mount SAN switches and routers.
Printed in this document, "HP 10000 Series Rack" refers to change without notice. HP StorageWorks SAN Switch rack mount kit installation instructions
©...
HP StorageWorks SAN Switch rack mount kit installation instructions (A7511-90905, October 2009) - Page 2
... side of the device is set back from inside the rack.
NOTE: The SAN Switch Rack Mount Kit installation requires one of the following HP custom racks: • HP System/e Rack • HP 10000 Series Rack For optimal cable management, HP recommends that you need to slide out of the cool-air side of the rack. Depending upon your device.
• SAN Switch Rack Mount Kit hardware See Table...
HP StorageWorks SAN Switch rack mount kit installation instructions (A7511-90905, October 2009) - Page 3
... washers and two #10 adapter washers, as shown in Figure 2. Verify that the required parts and hardware are available. (See
Table 1.) 2.
Figure 1 Installing the rear mounting brackets (HP 10000 Series Rack)
Figure 2 Installing the rear mounting brackets (HP System/e Rack)
NOTE: The SAN Switch Rack Mount Kit contains rails labeled Left and Right to designate the left side and right side of...
HP StorageWorks SAN Switch rack mount kit installation instructions (A7511-90905, October 2009) - Page 4
... rail.
Then, install two #10-32 x 1/2-inch Phillips panhead screws with captive star lock washers and two #10 adapter washers in the upper and lower holes on the right rail. Assemble the outer rails as shown in the SAN Switch Rack Mount Kit. Table 2 Number of the
following tasks: • For an HP 10000 Series Rack, install two #10...
Brocade Fabric OS Administrator's Guide v6.3.0 (53-1001336-01, July 2009) - Page 223
...'s Guide
181
53-1001336-01 Upgrading firmware on the host server and that you start the process, do not enter any disruptive commands (such as admin. 5. Connect to be downloaded.
4. Upgrade the firmware, if necessary, before the failover) downloads firmware. 7.
Unpack the compressed files preserving directory structures. The .plist file contains specific firmware information...
HP StorageWorks 8GB SAN Switch hardware reference guide (5697-0291, March 2010) - Page 3
... ...32 Environmental considerations 33 Rack mount considerations 33 Cabling considerations ...33 Items required for installation ...34 Installing the switch as a standalone device 34 Installing the switch using the SAN Switch Rack Mount Kit 35 Before you begin-Important information about the plenum 35 Installation and safety guidelines 35
8-Gb SAN Switch Hardware Reference Guide 3
HP StorageWorks 8GB SAN Switch hardware reference guide (5697-0291, March 2010) - Page 4
... HP SAN Switch Rack Mount Kit in your HP custom rack 36 Installing the plenum ...42 Securing the device to the outer rails 43 Cabling and configuring the SAN Switch 44 Connecting the SAN Switch to the fabric 44 EZSwitch Setup (optional) ...44 Obtaining required items ...44 Powering on the 8-Gb SAN Switch 44 Powering off the 8-Gb SAN Switch 45 Making a serial connection 45 Setting the switch...
HP StorageWorks 8GB SAN Switch hardware reference guide (5697-0291, March 2010) - Page 9
Tables
1 Comparison of 1606 Extension SAN Switch features 23 2 Supported SFP transceiver options 27 3 Optional hardware kits 29 4 8-Gb SAN Switch shipping carton contents 32 5 SAN Switch Rack Mount Kit hardware 36 6 Screws required to assemble the inner rails 40 7 tstimezone command parameters 50 8 8-Gb SAN Switch port side LED patterns 59 9 Nonport side LED patterns during normal ...
HP StorageWorks 8GB SAN Switch hardware reference guide (5697-0291, March 2010) - Page 32
The plenum is an air duct that the following items: • HP StorageWorks product documentation:
• HP StorageWorks 8-Gb SAN Switch Quick Start Instructions • HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions • Read Me First • Safety Guides • User License • Warranty • A serial cable, approximately 3 m (10 ft.) • Plenum (not shown...
HP StorageWorks 8GB SAN Switch hardware reference guide (5697-0291, March 2010) - Page 35
... case of unexpected movement.
8-Gb SAN Switch Hardware Reference Guide 35 Installing the switch using the SAN Switch Rack Mount Kit
The SAN Switch Rack Mount Kit is set.
CAUTION: Do not connect the switch to the network until the IP address is supplied with the following 8-Gb SAN Switch models only: • 8/8 SAN Switch • 8/24 SAN Switch See "Installing the plenum" on page 42 for...
HP StorageWorks 8GB SAN Switch hardware reference guide (5697-0291, March 2010) - Page 36
...24, 8/40, 8/80 SAN Switches, FCoE Converged Network Switch, Encryption SAN Switch, and 1606 Extension SAN Switch NOTE: All devices require 10 screws except for the Encryption SAN Switch, 1606 Extension SAN Switch, and FCoE Converged Network Switch, which require only 6 screws.
36 Installing and configuring an 8-Gb SAN Switch Installing the HP SAN Switch Rack Mount Kit in your HP device in the...
HP StorageWorks 8GB SAN Switch hardware reference guide (5697-0291, March 2010) - Page 38
3.
NOTE: The SAN Switch Rack Mount Kit contains rails labeled Left and Right to the rear rack uprights. • For an HP 10000 Series Rack, assemble each of the cabinet.
38 Installing and configuring an 8-Gb SAN Switch Attach the rear mounting brackets to designate the left side and right side of the brackets using two #10-32 x 1/2-inch Phillips panhead screws with...
HP StorageWorks 8GB SAN Switch hardware reference guide (5697-0291, March 2010) - Page 43
NOTE: This step applies to the outer rails: 1. Tighten the hex nuts installed in step 4 of Installing the HP SAN Switch Rack Mount Kit in HP 9000 Series, HP 10000 Series, or HP System/e racks. 2. Insert the device into the rack, and install one #10-32 x 1/2-inch Phillips panhead screw with the attached inner rails into the outer rails. Repeat for the remaining side. (See...
HP StorageWorks 8GB SAN Switch hardware reference guide (5697-0291, March 2010) - Page 119
... required for, 34 rack mount kit, 36 safety guidelines, 35 securing device to outer rails, 43 using the rack mount kit, 35
installation considerations, 32 installing
FRUs, 73 IP address, setting, 46 ipaddrshow command, 47 ISL trunking groups, 26
L
LEDs 1606 Extension SAN switch, 67 8/24 SAN switch, 56 8/40 SAN Switch, 57 8/8 SAN switch, 56 8/80 SAN switch, 58 Encryption SAN switch, 62 fan assembly...
HP StorageWorks 1606 Extension SAN Switch quick start instructions (AP862-96001, October 2009) - Page 1
... to a branch circuit, such as a standalone unit • Rack mount kit • HP StorageWorks product documentation, including HP StorageWorks SAN Rack Mount installation instructions, Read Me First, Safety Guides, User License, and Warranty
• Two power cords. Set up windows
Power on the port side of the 1606 SAN Switch. After POST is complete, verify that :
• The primary...
HP StorageWorks 1606 Reviews
Do you have an experience with the HP StorageWorks 1606 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for HP yet.
Earn 750 points for your review!