Homelite UT10589 Support and Manuals
Get Help and Manuals for this Homelite item
View All Support Options Below
Free Homelite UT10589 manuals!
Problems with Homelite UT10589?
Ask a Question
Free Homelite UT10589 manuals!
Problems with Homelite UT10589?
Ask a Question
Most Recent Homelite UT10589 Questions
New Bump Feed Spool And Knob.
I am unable too get the new bump feed spool off the machine
I am unable too get the new bump feed spool off the machine
(Posted by Tyronepearce 7 years ago)
Magneto Air Gap.
I wlould like to know the air gap setting for the magneto to flywheel .
I wlould like to know the air gap setting for the magneto to flywheel .
(Posted by mondrojp 9 years ago)
Won't Keep Running
I tried starting my chainsaw te first time since last Spring. New gas, regapped plug. I had left gas...
I tried starting my chainsaw te first time since last Spring. New gas, regapped plug. I had left gas...
(Posted by dlong3211 9 years ago)
Popular Homelite UT10589 Manual Pages
User Manual - Page 4
... competent chain saw service personnel. (For example, if improper tools are very hot during and after operation of less than the items listed in the instruction manual and all maintenance, should be appropriate to instruct other than 3 in the user's hands due to rentals as well as privately owned saws.
English
Failure to follow all body parts...
User Manual - Page 5
... the fuel cap securely after adjustment has been made, contact an authorized service center for adjustment and discontinue use by homeowners and other cuts (i.e., bucking cuts, etc.).
Keep SAFE-T-TIP® anti-kickback nose guard properly mounted on the guide bar to Adjusting the Carburetor in the Maintenance section of this manual for added information on...
User Manual - Page 8
... B175.1 when tested with specific chain saws.
Page 8 - Chain Saw Powerhead A chain saw without the saw chain. Felling The process of cross cutting a felled tree or log into lengths. This handle is supported by the motor and is for a chain brake. Low-Kickback Chain A chain that complies with the kickback performance requirements of the guide bar to the hand position...
User Manual - Page 16
... clothing and keep all parts of your body away from the chain/guide bar and muffler. ...chain saw on a stable surface so that the on /stop switch repaired before storing.
away.
To stop the engine, move the on/ stop switch will move around the guide bar when adjusting the idle speed. For additional safety, set to the STOP position, have the on /stop switch to follow these instructions...
User Manual - Page 27
...for tension adjustment. English
Fig. 42 The chain is correctly tensioned when there is no sag on the underside of the guide bar, the chain is snug...chain brake is too tight, it will rotate without binding.
n Finger-tighten the bar mounting nuts. n Lift the tip of the bar chain tensioning pin hole. n Replace the clutch cover and bar mounting nuts. NOTE: If chain is not set...
User Manual - Page 28
... gloves when performing maintenance on the underside of the chain increases.
check the chain tension frequently and tension as a guide to help determine the correct warm chain tension. CAUTION:
A chain tensioned while warm may be turned by hand without binding. Check the "cold tension" before setting the chain tension. Fig. 43 Fig. 44 Fig. 45 Fig. 46...
User Manual - Page 30
...protective gloves when performing maintenance to the chain to Adjusting The Chain Tension.
CAUTION:
A dull or improperly sharpened chain can only be obtained when all ...careful to file all of your filing at the midpoint of the tooth. n Tension the chain prior to replace or repair a damaged chain can cause serious injury.
n Put a few firm strokes on each return stroke. WARNING:
...
User Manual - Page 34
... Figure 64. away. Failure to the chain saw chain turning at least 50 ft. Before adjusting the carburetor: n Use a brush or compressed air to adjustment
of this manual. n Allow the engine to warm up prior to clean the
starter cover vents. Do not allow bystanders close to follow these instructions could result in the Maintenance section of...
User Manual - Page 37
... engine will remove
all Federal and local regulations for gasoline. Please have an authorized service center adjust this engine if it is inaccessible to purge fuel from carburetor. EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST
Emissions Parts
Inspect Before Each Use
Clean Every 5 Hours
Replace
Clean Every
Every 25 Hours 25 Hours
or Yearly
or Yearly...
User Manual - Page 38
... lever to Spark Plug Replacement earlier in .
310627001
Chain Part Number 901212001 901212002 671258001
Drive Links 52 56 62
TROUBLESHOOTING
Problem
Possible Cause
Solution
Engine will clear excess fuel from engine. Contact an authorized service center for carburetor adjustment.
Carburetor requires "H" (High Jet) adjustment.
Engine starts but Carburetor requires
will not run...
User Manual - Page 39
.... Inspect guide bar and chain for a rebuild kit. English speed. Oiler is too tight. Refer to Adjusting the Carburetor in the Maintenance section of this manual. system.
Air leak in the intake Contact an authorized service center for damage. Bar and chain running hot and smoking. Chain brake is too tight. Chain tension is engaged.
TROUBLESHOOTING
Problem
Possible...
User Manual - Page 40
...operating instructions as rental or commercial. Spark Plugs, Carburetor, Carburetor Adjustments, Ignition, Filters
B. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. This warranty gives you specific legal rights, and you may also have other income-producing purpose.
To locate your nearest Homelite authorized service...
User Manual - Page 41
... purchaser and each new engine written instructions for its warranty procedures or policies within five days upon request by the failure of a warranted part still under warranty. Any replacement part or service that is equivalent in performance and durability may include parts such as the carburetor or fuel injection system, the ignition system, catalytic converters, fuel tanks, valves...
User Manual 2 - Page 8
Always mention the model number in all correspondence regarding your CHAIN SAW or when ordering repair parts. Key Nos. 20-31 1 6 310041002 Crankshaft & Piston Assembly (Inc. NUMBER
DESCRIPTION
QTY
1 290298001 Ignition Switch Harness 1 2 660613001 Bolt (M5 x 25.4 mm 2 3 309261001 Ignition Module 1 4 309892002 Short Block Assembly (Inc. Key Nos. 10-19 1 5 310503002 ...
Getting Started Guide - Page 1
....
3
O
Set ignition switch to RUN (I) position.
4
HOW TO GET STARTED
5
Press fully and release x7 PRIMER BULB 7 times.
6
Pull CHOKE lever to RUN position.
IMPORTANT: It is NOT an indication of a leak. WARNING: This Engine Starting Procedure is not a substitute for chain saws to ensure your new tool on-line. Go to www.homelite.com...
Homelite UT10589 Reviews
We have not received any reviews for Homelite yet.