Homelite UT43103 Support and Manuals
Get Help and Manuals for this Homelite item
This item is in your list!
View All Support Options Below
Free Homelite UT43103 manuals!
Problems with Homelite UT43103?
Ask a Question
Free Homelite UT43103 manuals!
Problems with Homelite UT43103?
Ask a Question
Popular Homelite UT43103 Manual Pages
User Manual - Page 3
...chain saw in this unit until you have repaired by the front handle with ANSI Z87.1 as well as in any way.
Make sure your hands. Keep cord away from the falling tree. READ ALL INSTRUCTIONS...the unit unplugged and the guide bar and saw . ...manual. Failure to use the next heavier gauge. This plug will cause a drop in line voltage resulting in loss of at all parts...
User Manual - Page 4
... contacting any attachments or devices not listed for spring back so that you off .
English A chain saw service, other conditions that is extremely dangerous. NOTE: The size of children. The chain saw should be properly repaired or replaced by your nearest Homelite service dealer.
Check for lubricating and changing accessories.
Keep handles dry, clean, and...
User Manual - Page 6
... overreach when cutting. When making a replacement, be sure to order one of the low kickback qualities and extra caution should be used. The proper size SAFE-T-TIP® nose guard comes installed on the guide bar to be ready to original chain or has been certified as low kickback chain per ANSI B175.1. Don't let...
User Manual - Page 10
... maintain position while sawing.
Page 10 -
This handle is for the right hand.
Oiler Control
A system for use when felling or bucking to pivot the saw chain.
Replacement Saw Chain
A chain that supports and guides the saw chain.
Drive Sprocket or Sprocket
The toothed part that transmits motion from contacting the wood.
Normal Cutting Position
Those positions assumed in...
User Manual - Page 12
... allows user to stop the unit.
Parts on the end of the guide bar from being accidently started.
n Do not discard the packing material until the parts are not assembled to prevent the motor from contacting the wood. PACKING LIST
Chain Saw Sleeve Operator's Manual
WARNING:
If any parts on the tool and in serious personal...
User Manual - Page 14
... slack is to the chain cover. WARNING:
Keep body to stop once the trigger switch is released. Refer to Adjusting the Chain Tension in plug loosening from receptacle.
this manual.
n Make sure no... straddle the saw : n Make sure chain tension is at desired setting. Starting the chain saw or chain, or lean over cord hitch. n Make sure the chain cover lock knob is tight to the left...
User Manual - Page 22
..., make sure the tool is required. WARNING:
Do not at proper tension may be damaged by their use only identical Homelite replacement parts. WARNING:
Never start the motor before installing the guide bar, chain, chain cover, and chain cover lock knob. Page 22 - Use of the unit under normal operating conditions. Failure to remove dirt, dust, lubricant, grease...
User Manual - Page 30
Guide Bar Part Number 310625001
Chain Part Number 901212001
TROUBLESHOOTING
Drive Links 52
Problem
Possible Cause
Solution
Bar and chain running hot and smoking. Check chain tension for damage.
Chain cover lock knob is not raised.
Check oil tank. Retension chain, Refer to adjust chain tension.
Raise tip of chain. CALL www.homelite.com
CALL US FIRST
For ...
User Manual - Page 31
... authorized service center. Spark Plugs, Carburetor, Carburetor Adjustments, Ignition, Filters
B.
HOMELITE'S OBLIGATION UNDER THIS WARRANTY IS STRICTLY AND EXCLUSIVELY LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS AND HOMELITE DOES NOT ASSUME OR AUTHORIZE ANYONE TO ASSUME FOR THEM ANY OTHER OBLIGATION. This warranty applies to all models if used for personal, family, or household...
User Manual 2 - Page 2
...DESCRIPTION
QTY
Chain Cover Lock Knob 1 SAFE-T-TIP 1 Screw w/Washer 1 Sprocket 1 Screw (M3 x 12 mm 2 Adjustment Pin Cover 1 Retaining Ring 1 Washer (M4 1
Sleeve Operator's Manual
NOTE: The assembly shown represents an important part of alteration or damage to the system, service should be performed by your nearest Homelite authorized service dealer.
2 MODEL NUMBER UT43103 − ALL...
User Manual 2 - Page 3
MODEL NUMBER UT43103 − ALL VERSIONS
12 8
15
2
28 19
13 14
26 7
3
5
4
6 18
15 21
26
15
27
16
17
25
29 15 27
26
22
27
10
15 15
20 27
19
15 30
24
23
11 3 SECTION "A"
HOMELITE CHAIN SAW -
User Manual 2 - Page 4
...'s Manual
3-22-11 (REV:01)
Section "A" represents an important part of the double insulated system of this tool requires dielectric testing to ensure customer safety and to comply with company requirements.
4 Any repair to the motor housing. Always mention the model number in all correspondence regarding your CHAIN SAW or when ordering repair parts.
HOMELITE CHAIN SAW - PART NUMBER...
User Manual 2 - Page 5
MODEL NUMBER UT43103 − ALL VERSIONS
BLACK
WIRE NUT
MOTOR
WHITE
POWER CORD
BLACK
SWITCH
WIRING DIAGRAM
5 HOMELITE CHAIN SAW -
Replacement Parts List - Page 2
UT43103
The model number will be found on a plate attached to the system, service should be performed by your ELECTRIC CHAIN SAW or when ordering replacement parts.
1
SEE NOTE
16
8
19
18 17
15 14
6 17
4 3 2
10 11
56
7 20 6
9
13 12
KEY NO.
1 2 3 4 5 6 7 8 9 10 11 12
PART NUMBER
34109154G 33904159G 33202419G 33301419G 34111159G 32203404G 31102573G 33302102G 34106159...
Homelite UT43103 Reviews
Do you have an experience with the Homelite UT43103 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Homelite yet.
Earn 750 points for your review!