Honeywell NX4L1 Support and Manuals
Get Help and Manuals for this Honeywell item
View All Support Options Below
Free Honeywell NX4L1 manuals!
Problems with Honeywell NX4L1?
Ask a Question
Free Honeywell NX4L1 manuals!
Problems with Honeywell NX4L1?
Ask a Question
Most Recent Honeywell NX4L1 Questions
Nx4l1 Power Supply
How to switch from 12 vdc to 24 vdc on power supply
How to switch from 12 vdc to 24 vdc on power supply
(Posted by artiefields 7 years ago)
Switching Between Panels
I have a 3 panel system. The select panel sees all 3 boxes. When I switch to panel 2 or 3, a box app...
I have a 3 panel system. The select panel sees all 3 boxes. When I switch to panel 2 or 3, a box app...
(Posted by wrlym 10 years ago)
Popular Honeywell NX4L1 Manual Pages
Installation Guide - Page 4
... 5.15 NetAXS™/NetAXS™ Access Controller Panel Connection Detail 46
6.0 NetAXS™ Startup ...47 6.1 LED Operation...47
7.0 Hardware Specifications ...49 7.1 Relay Contacts ...49 7.2 Reader Interface ...49 7.3 Maximum Output Loading 49 7.4 Common Connections...49 7.5 Mechanical...49 7.6 Environment...50 7.7 Communications and Wiring 50 7.8 Reader Wiring...51 7.9 NX4L1 Panel Wiring...
Installation Guide - Page 11
...Use of what to do is a life safety requirement. Warning: Use suppressors on a regular basis by instructing the end user in accordance with the commercial carrier responsible. To prevent damage always follow these procedures:
NetAXS Access Control Unit NX4L1 Installation Guide, Document 7-901099, Revision A
1 Warning: Personal injury or death could occur, and the equipment could make...
Installation Guide - Page 12
... on Terminals, Printers, Communications Products and Upgrade kits is determined to be handled through the Customer which are defective or defective under normal use. The Customer shall hold harmless and indemnify Honeywell from and against all claims, demands, losses and liability for service, repair, credit or exchange.
NetAXS™ NX4L1 Installation Notices
• Use static shield...
Installation Guide - Page 13
... OR SPECIAL DAMAGES TO ANY PERSON RESULTING FROM THE USE OF HONEYWELL PRODUCTS.
1.4 Federal Communications Commission
This equipment has been tested and found to comply with the instructions, may cause harmful interference to operate the equipment. NetAXS Access Control Unit NX4L1 Installation Guide, Document 7-901099, Revision A
3 These limits are designed to the equipment unless...
Installation Guide - Page 14
...Connection via NetAXS™" on page 32, and Section 5.4, "RS-232 Connection" on page 28) with the NetAXS panel.
4
www.honeywell.com Because UL has reviewed the NetAXS panel only...the NetAXS panel has not been evaluated by Underwriters Laboratories Incorporated for Access Control System Units - NetAXS™ NX4L1 Installation Notices
1.6 Underwriters Laboratories Incorporated
The NetAXS&#...
Installation Guide - Page 16
..., and batteries. The 24V power supply provides power for the panel control board, which is overridden in a pre-wired cabinet. The following figure shows the NX4L1 panel components.
NetAXS™ NX4L1 Installation Panel Components and Descriptions
3.0 Panel Components and Descriptions
The NX4L1 access control unit consists of fire emergency by the HPACM8 Power Distribution Board.
Installation Guide - Page 18
... mm (23.9 inches) high, 90 mm (3.54 inches) deep.
Replace the batteries every 2 to operate the system. NetAXS™ NX4L1 Installation Panel Components and Descriptions
3.2 Power Supply
The NX4L1 uses an internal 115 VAC to the supply per the National Electrical Code as well as any local electrical codes, including the safety ground wire.
The batteries are required...
Installation Guide - Page 19
... Power Connection option, see "System Configuration" on page 31 and "Jumper Settings" on the power inlet terminal block. Wiring to the enclosure power inlet terminal block. Connect the shield to the panel. Apply power to the grounding studs.
7. NetAXS Access Control Unit NX4L1 Installation Guide, Document 7-901099, Revision A
9 After the power-up sequence, check the LEDs to...
Installation Guide - Page 28
... defaulted for instructions on the control panel. See the NetAXS™ Access Control Unit User's Guide for the control of the cable. Caution: The system has not been verified for details.
18
www.honeywell.com The NX4L1 is pre-wired to determine the total resistance. If the application requires a separate supply, refer to the Power Distribution Output board installation manual for...
Installation Guide - Page 31
...through a 50-foot RS-232 cable (HAS part number CBL50).
Figure 10: RJ-45 Serial Port
NetAXS Access Control Unit NX4L1 Installation Guide, Document 7-901099, Revision A
21 A second cable can be used to provide communication to be obtained by contacting your Honeywell Access System Representative. Note: Because UL has reviewed the NetAXS panel only as a standalone system, the computer...
Installation Guide - Page 32
... switch setting information. DIP switch positions 1-5 are provided for supplying biasing and end-of the RS-485 network. Note: If an RS-485 network has a NetAXS™ Gateway panel, no N1000-II, N1000-III, or N1000-IV are present.
Use the jumpers on both ends are allowed on the network. NetAXS™ NX4L1 Installation Installation
Figure...
Installation Guide - Page 34
...; panel has a port for each TCP/IP connection.
24
www.honeywell.com The Ethernet TCP/IP interface provides 10/100 Mbit Ethernet support for an Ethernet TCP/IP interface (see Figure 14, Ethernet TCP/IP Configuration). NetAXS™ NX4L1 Installation Installation
Ethernet TCP/IP Communications
Figure 14: Ethernet TCP/IP Configuration
Terminal
Network Interface Card Inside...
Installation Guide - Page 36
Figure 16: DIP Switch and Jumper Location
J37 J36
DIP Switches
26
www.honeywell.com NetAXS™ NX4L1 Installation Installation
4.8 DIP Switch Settings
Figure 16 locates the NX4L1 DIP switch panel and the J36 and J37 jumpers.
Installation Guide - Page 38
... 2
Baud rate (switches 7 and 8) - 7 = OFF, 8 = ON
OP Mode (switches 9 and 10) - 9 = OFF, 10 = OFF
28
www.honeywell.com NetAXS™ NX4L1 Installation Installation
4.9 Jumper Settings
The NX4L1 panel control board includes jumpers 36 and 37, which set both jumpers on a given panel must set end-of-line termination and biasing for the Multidrop RS-485 Line.
A MIRO-32/0 module has...
Installation Guide - Page 40
Figure 17: Default Downstream I /O system configuration with Wiring
30
www.honeywell.com NetAXS™ NX4L1 Installation Installation
The following figure shows the default downstream I /O Configuration with communication and power wiring.
Honeywell NX4L1 Reviews
We have not received any reviews for Honeywell yet.