Husqvarna 372 XP G Support and Manuals
Get Help and Manuals for this Husqvarna item
View All Support Options Below
Free Husqvarna 372 XP G manuals!
Problems with Husqvarna 372 XP G?
Ask a Question
Free Husqvarna 372 XP G manuals!
Problems with Husqvarna 372 XP G?
Ask a Question
Husqvarna 372 XP G Videos
Husqvarna 372xpg akcja
Duration: 1:06
Total Views: 13,377
Duration: 1:06
Total Views: 13,377
372XPG-Big Bore -
Duration: 1:04
Total Views: 548
Duration: 1:04
Total Views: 548
Popular Husqvarna 372 XP G Manual Pages
Owners Manual - Page 4
... use 22 General working instructions 22 How to avoid kickback 28 MAINTENANCE General 30 Carburetor adjustment 30 Checking, maintaining and servicing chain saw safety equipment 31 Muffler 33 Starter 34 Air filter 35 Spark plug 35 Lubricating the bar tip sprocket 36 Needle bearing lubrication 36 Adjustment of the oil pump 36 Cooling system...
Owners Manual - Page 6
... Bumper spike 17 Chain catcher 18 Clutch cover 19 Rear handle with right hand guard 20 Throttle control 21 Throttle lockout 22 Decompression valve 23 Combination spanner 24 Chain tensioning screw 25 Operator's manual 26 Transport guard 27 Switch for heated handle (Model 372 XPG) 28 Information and warning decal 29 Product and serial number plate...
Owners Manual - Page 7
... Technical data. CAUTION! the wrong combination of kickback! See instructions under close
supervision.
GENERAL SAFETY PRECAUTIONS
Before using a new chain saw until sufficient chain oil has reached the chain.
contain chemicals that is designed for forest service is faulty. Therefore remove the spark plug cap
when the machine is equipped with active or
passive...
Owners Manual - Page 14
... hold the clutch cover/chain brake. NOTE! Detailed information regarding the use of depth gauge setting
• ...saws varies from the underside of the depth gauge that you adjust the depth gauge setting ...the chain is worn out and should be replaced. When the length of the chain tensioning screw... the correct depth gauge setting for your model.
14 - See instructions under the heading What ...
Owners Manual - Page 18
...correct mixture is recommended. Environment fuel
HUSQVARNA recommends the use HUSQVARNA two-stroke engine oil, which can occur. Two-stroke oil
• For best results and ...using a mixture of fuel (see instructions under the heading Carburetor). When mixing small amounts of oil to be emptied and cleaned.
Gasoline, litre
5 10 15 20 US gallon 1 2 1/2 5
Two-stroke oil, litre 2% (1:50) 0,10 ...
Owners Manual - Page 19
... have spilled fuel on the machine. See instructions under the heading Maintenance schedule.
Transport and storage
• Always store the chain saw , the fuel and chain oil tanks should therefore always fill the chain oil tank and fuel tank at the same time. You should be replaced at least 10 ft (3 m) from the refuelling...
Owners Manual - Page 24
... insecure support.
See instructions under the headings Cutting equipment and Technical data.
5 Do the conditions and surrounding terrain affect how safely you are recommended by
! Cutting with a pushing chain. When you .
8 Unless the user resists this case the chain saw and the position of the kickback zone.
3 Make sure the chain will not split.
from...
Owners Manual - Page 30
... user must only carry out the maintenance and service work described in this gives a higher idle speed; Your Husqvarna product has been designed and manufactured to specifications that described in this could cause damage.
• Now start the machine according to the starting instructions and let it warm up for extended...
Owners Manual - Page 35
...oil. Fit the starter pulley and tension the recoil spring. An air filter that the electrode gap is in order to avoid: • Carburettor malfunctions • Starting problems • Loss of air filters according to engine parts... in operating problems and starting difficulties. See instructions under tension in the starter. The spark plug should be replaced with a ...
Owners Manual - Page 36
... bar tip sprocket each time you refuel. See instructions under the heading Cutting
equipment. Adjustment of : 1 Air intake on the starter. 2 Air guide plate. 3 Fins on the flywheel. 4 Cooling fins on the cylinder. 5 Cylinder cover (directs cold air over the cylinder).
5
The clutch drum has a needle bearing on the output shaft.
4
This...
Owners Manual - Page 38
... the clutch drum bearing.
On chain saws with regard to be sure it if necessary. Clean the spark plug. Empty the fuel tank and clean the inside . On chain saws without a catalytic converter, check the cooling system weekly. Monthly maintenance Check the brake band on the chain brake for excessive wear and replace if necessary. Empty the oil...
Owners Manual - Page 39
.../mm Stroke, inch/mm Idle speed, rpm Power, kW/ hp@ rpm Ignition system
Spark plug
Electrode gap, inch/mm Fuel and lubrication system Fuel tank capacity, US pint/litre Oil pump capacity at 9,000 rpm, ml/min Oil tank capacity, US pint/litre Type of oil pump Weight Chain saw without bar or chain, empty tanks, lb/kg...
Owners Manual - Page 42
FEDERAL EMISSION CONTROL WARRANTY STATEMENT
EMISSION CONTROL WARRANTY PARTS LIST
1 Carburetor and internal parts 2 Intake pipe, airfilter holder and carburetor bolts. 3 Airfilter and fuelfilter covered up to maintenance
schedule. 4 Spark Plug, covered up to maintenance schedule 5 Ignition Module 6 Muffler with catalytic converter
MAINTENANCE STATEMENT
The owner is...
Parts List - Page 23
...SPARK PLUG
3
725 53 33-55 SCREW IHSCM
4
537 29 44-01 DECOMPRESSION VALVE
5
537 20 71-01 PLUG
6
503 55 22-01 PLUG
7
523 04 91-01 HEAT DEFLECTOR
8
503 77 59-01 GASKET MUFFLER
9
503 96 15-01 GASKET...SNAP RING
13
577 57 24-01 NEEDLE BEARING
14
503 64 72-01 GASKET KIT
372XP X-TORQ, 2013-09
Remark BPMR7A
Set of gaskets
Qty Kit 1 1 4 1 11 11 1 1 14 1 14 11 2 1, 10 2 1,...
Parts List - Page 29
IGNITION SYSTEM
Ref
Part no. Description
2
537 18 98-01 THERMOSTAT ASSY
3
537 06 32-01 RETAINER
4
503 55 49-01 SWITCH
5
537 06 53-02 FOIL ELEMENT
6
...48 54-02 SPARK PLUG CAP
18
503 21 38-01 SCREW CRCSRT
19
503 71 82-01 SWITCH
20
503 70 59-01 HEATING PLATE
21
503 62 61-01 CABLE
22
503 89 76-01 CABLE
23
503 21 28-10 SCREW CCRPANT
24
503 22 04-01 NUT
372XP X-TORQ, 2013-09...
Husqvarna 372 XP G Reviews
We have not received any reviews for Husqvarna yet.