IBM 847671U - Netfinity 3000 - 71U Support and Manuals
Get Help and Manuals for this IBM item
Popular IBM 847671U Manual Pages
Hardware Maintenance Manual - Page 9
IBM Netfinity 3000 - Type 8476
General Checkout 4 Diagnostics 6
Diagnostic test programs 7 Power-on self-test (POST 8 POST beep codes 9 Error messages 9
POST error messages and beep codes . . . 9 SCSI error messages 9 Diagnostic error messages 9 Software-generated error messages . . . . . 10 Installing files from option diskettes 10 Running the diagnostic test programs 11 Power-on ...
Hardware Maintenance Manual - Page 17
... is set to [Enabled], POST also generates beep codes to indicate successful completion or the detection of diagnostic codes, see "Symptom-to-FRU index" on page 160.
they also can be performed by error messages should be numeric. More than one beep indicates that a problem exists;
Troubleshooting and servicing of beep codes, see "Symptom-to identify a failing part. The...
Hardware Maintenance Manual - Page 20
...selected Continue in the Configuration/Setup Utility program, you powered-...specific to toggle between choices
12 Netfinity Server HMM If you have the password prompt set both power-on and administrator passwords, you did not make a change any menu items that indicate components that are displayed on the POST Startup Errors screen; If you can attempt to identify and correct the problem...
Hardware Maintenance Manual - Page 21
... if you have finished viewing and changing settings, press Esc to return to -FRU index" on the screen.
6.
IBM Netfinity 3000 - The system will save all settings as they currently appear in the Configuration/Setup Utility program, note the following:
You will get a POST error message, and then the Configuration/Setup Utility program will automatically restart. then...
Hardware Maintenance Manual - Page 29
...8476 21 If you installed or removed SCSI devices, run the Configuration/Setup Utility program if you receive an error message instructing you want or need to change the settings only to resolve ... does not work. Screen messages indicate that are not supported. Some configurations are used by the application program or the device driver. If this happens, the new memory-address space and...
Hardware Maintenance Manual - Page 30
... program menus" on the configuration changes that occurred, the error message that a configuration change an option and restart the server, the following :
Continue Exit Setup
Note Depending on page 24. You are then prompted to enter the Configuration/Setup Utility program to manually update the configuration settings or to restart the server.) 2.
Review the information that...
Hardware Maintenance Manual - Page 37
... by an unattended method, such as you try to start again. Setting and changing a power-on the screen as a modem or timer. Password prompt Off mode is restored, the server will be able to view limited information in password prompt On mode. IBM Netfinity 3000 - restart and resume operating in this mode, without operator intervention...
Hardware Maintenance Manual - Page 42
.... 3.
From the Configuration/Setup Utility program menu, select System Security; You might need to perform a POST/BIOS (flash) update under the following circumstances:
When you receive a system message instructing you to do so When you install a new microprocessor (see "Microprocessors" on page 130) When you receive an error code (see "Microprocessor speed switches settings" on page 153...
Hardware Maintenance Manual - Page 44
...manually configure it by setting switches or jumpers on page 20 for an installed adapter:
36 Netfinity Server HMM
If the required resources are not Plug and Play devices. To store the legacy resource information for information about handling resource conflicts. Support... in memory to provide installation information to Disabled, the system cannot update the configuration during startup....
Hardware Maintenance Manual - Page 46
.... This process is , the Ethernet controller will not attach to the ServerGuide package for instructions on installing device drivers. A full-duplex switch that supports manual overrides. In this device driver. Refer to the Netfinity 3000 server in the network must install a device driver to enable the operating system to the Ethernet documentation for the different operating speeds...
Hardware Maintenance Manual - Page 55
... Diskette (POST/BIOS update)
into drive A. 5.
Power-off the server and all external cables attached to the server is interrupted while POST/BIOS is for the wrong switches, you check the orientation of a small screwdriver to http://www.ibm.com/support/ on page 142.
2. Note
If you change the settings for reference only.
It...
Hardware Maintenance Manual - Page 140
... board illustration" on page 153, or see the label inside the server. For information about the appropriate switch settings, see "Disconnecting cables and removing the side cover" on the top of the microprocessor. To install a microprocessor: 1. Locate the microprocessor socket on the system board and is referred to the system board. Remove...
Hardware Maintenance Manual - Page 159
... 24. 4.
IBM Netfinity 3000 - Type 8476 151 You might need to install device drivers after you install or replace options, or after you restart the server, you remove a SCSI device, the server might not recognize any device drivers, or update or save the system configuration, the server is set. 2. To run the Configuration/Setup Utility program, follow the instructions in the...
Hardware Maintenance Manual - Page 171
....
163 Clock not updating or invalid time set.
164 POST detected a base memory or extended memory size mismatch error.
167 Microprocessor installed that device.
3.
FRU/Action
1. System Board
1. Reseat adapters 2. Adapter Memory 2. System Board
1. Run Setup 2. Had a device been added, removed, changed location? Power-on external devices first, then power-on computer.
4. CMOS Backup...
Hardware Maintenance Manual - Page 233
... label attached. otherwise, the fan might start turning while you open the server covers, unless instructed otherwise in the server; Caution: Never remove the cover on top of the rack model of these parts, contact an IBM service technician. Related service information 225 There are present inside the power supplies, power backplane, or AC box. Caution...
IBM 847671U Reviews
We have not received any reviews for IBM yet.