IC Realtime IPFX-S20F-W1 Support and Manuals
Get Help and Manuals for this IC Realtime item
View All Support Options Below
Free IC Realtime IPFX-S20F-W1 manuals!
Problems with IC Realtime IPFX-S20F-W1?
Ask a Question
Free IC Realtime IPFX-S20F-W1 manuals!
Problems with IC Realtime IPFX-S20F-W1?
Ask a Question
Popular IC Realtime IPFX-S20F-W1 Manual Pages
Product Manual - Page 2
...with rated voltage which conforms to Limited power Source requirement according IEC60950-1. This user's manual is operating normally, which may cause accidental damage.
14
Please keep this series product...The device needs to be installed in the location where professional staff can cover
(professionals need to know the attentions of using your local electrical safety codes. The power ...
Product Manual - Page 3
...installation and application, it may stain dust, grease or fingerprint, you can be fixed by unauthorized modification or attempted repair...problems caused by users
themselves. For the IP camera firmware of some water and then
wipe gently. You need to upgrade the camera firmware or upgrade the ONVIF password manually.
Please modify the default password...-sale service to replace desiccant ...
Product Manual - Page 4
... updated according to the product upgrade without prior written notice. This equipment generate, uses and can be determined by turning the equipment off and on a circuit different from that to which can radiate radio frequency energy and, if not installed and used in accordance with part 15 of the FCC Rules. Disclaimer
This manual...
Product Manual - Page 5
Accessory Name Network Camera Quick Start Guide CD
Amount 1 1 1
Accessory Name
Installation Position Map
Screw Package
Decoration Cover (Optional)
Amount 1
1 1
14
Note Please refer to the disk for more details, check and download the corresponding user's
manual and tool. Before installation, please open the package and check all the components are included. ...
Product Manual - Page 8
...3.5mm
port
TRS
Output audio signal to factory default settings.
RS232 sending port.
Alarm input port 1, receive ...DC12V;
Network port
Ethernet port
Connect to the instruction of device label.
I /O port
Cable port ...device according to restore factory default settings for more details. RS232 receiving port...device is used to the instruction of device label. Micro SD...
Product Manual - Page 9
... unit is mm (inch).
C2
Table 1-2
1.2 Dimension
Refer to Figure 1-6 for the dimension of Model C. Figure 1-4 Refer to alarm
C1
device.
The unit is mm (inch). N2 Alarm output port 2 (reserved). The unit is mm (inch). Port name
Cable port ...
Product Manual - Page 10
... default; There are for reference only; please refer to be installed respectively. please purchase it separately if
necessary. The unit is mm (inch). The unit is mm (inch).
Step 1 Rear pinhole box installation for front part. Figure 1-7 Refer to Figure 1-7 for the dimension of Model D. Note The following figures are four types of...
Product Manual - Page 11
...to fix the device on installation position map. 2) Open ...installation surface where the bolts are located. 4) Put the device into the holes you will install
the device. Figure 2-1 To install the back-end box, do the following steps when it is model A, B or C. Mode 1
14 Please select installation mode according to camera body via cable. Step 2 Front part installation for model...
Product Manual - Page 12
...). 2) Put the round lens into the inner barrel properly. 3) Twist the rotation fixing ring into the inner barrel and make sure the round
lens is model D.
Product Manual - Page 13
Please select installation mode according to this chapter. Connect Alarm Input / Output Port Note Some models do not support alarm function, which cannot be applied to the...waterproof.
Note It needs to a proper monitoring angle. 3) Tighten the adjusting screw firmly. Step 3 Installation for model F and G. When the input signal is connected to make it waterproof. Connect alarm ...
Product Manual - Page 14
...the device is corresponding to the WEB Operation Manual in WEB interface, make the camera have different...Set alarm output on the WEB, alarm output is corresponding to provide alarm output. Only some device support...corresponding settings upon alarm input and output on the WEB interface. Step 2
14 different models ... IP address on the
interface of alarm setup. Alarm input of WEB is...
Product Manual - Page 15
... begins to check more details. Step 7 Click OK to complete device initialization.
14
means initialization failed. Step 3
Set the device network segment, login user name and password, and then click OK. Figure 3-1 Step 5 Set new password and confirm password, select Email Address and input email address.
Step 4
Select the devices which is shown in Figure 3-1.
Product Manual - Page 16
...IP addresses need to the interface prompt if the interface displays guide of Software License Agreement and Online Upgrade.
14 Note Set the mode as Static, and enter the planned start IP... Please operate according to be modified, and then click
. Step 3
Set the device network segment, login user name and password, and then click OK.
Step 2
Click
to complete modification of Modify...
Datasheet - Page 1
... be easily installed into any indoor environment, which makes this camera suits even the most intense contrast lighting conditions.
Protection Supporting ±30...Support (Tripwire, Intrusion, Face Detect) ● Micros SD Support (128GB), PoE
System Overview
IC Realtime's IPFX-S20F-W1 is capable of multiple object behaviors such as PoE and Micro SD support up to 128GB. IVS also supports...
Datasheet - Page 2
... IOS, Android
CE (EN 60950:2000) UL:UL60950-1 FCC: FCC Part 15 Subpart B
1/1 channel In/Out 1 Port 2 channel In: 5mA...Manual Auto / Manual 3D DNR
Motion Detection Region of Interest Electronic Image Stabilization (EIS) Smart IR Defog Digital Zoom Flip Mirror Privacy Masking
Audio
Compression
Network
Ethernet
Protocol
Interoperability Max. DHCP;DNS;DDNS;PPPOE;IPv4/v6;QoS;UPnP;NTP; IPFX-S20F-W1...
IC Realtime IPFX-S20F-W1 Reviews
We have not received any reviews for IC Realtime yet.