Icom M802 Support and Manuals
Get Help and Manuals for this Icom item
Popular Icom M802 Manual Pages
Instruction Manual - Page 2
...Use Icom microphones only (supplied).
Place the unit in an electric shock. The heatsink will obstruct heat dissipation. This
manual contains important safety and operating instructions ...radio of choice, and hope you with Icom's philosophy of trouble-free operation. This may damage the transceiver.
R NEVER place the transceiver where normal oper-
FOREWORD
Thank you for the IC-M802...
Instruction Manual - Page 20
... IC-M802 and ...manual transmission with microphone's [PTT], or
grounding the SEND line of [ACC] connector is necessary before keying)
q Connect a CW keyer or an external electronic keyer to the [ACC] socket as described on your antenna...channel to transmit a CW signal. r Operate the CW keyer to operate CW mode. then
[CH] [F] [RX CLAR] [TUNE THRU] [F]
I Functions for break-in OFF setting...
Instruction Manual - Page 29
...Manual set
T: 4567.0kHz
R: 4567.0kHz
T:12345.0kHz
R:12345.0kHz
SEL
OK
IC-M802-1 IC-M802-2
Traffic frequency selection 2
****** Individual ****** -- D Operation outline
RX
12.345.0 J3E
GPS Lat 34 34'N
SP
Lon135 34'E
12:34
Exit
DSC menu
******* DSC...-- to store the condition into a TX memory channel.
****** Individual ******
--------- Category:Distress
To:987654321
Traffic...
Instruction Manual - Page 32
...
DSC menu
******* DSC MENU *******
--------
Traffic frequency --- Push [ENT] for 1 sec. Position
ÇIndividual
Group
All ships
Position REQ
Distress
Test
RX memory
TX memory
Set ...memory channel.
****** All ships *******
****** Individual ******
--------- Call ---------
Address ID ------
ÇManual set
T: 4567.0kHz IC-M802-1
R: 4567.0kHz
T:12345.0kHz IC-M802-2...
Instruction Manual - Page 33
...of the pre-programmed frequencies or "Manual set" then push [ENT]. ✔ When a pre-programmed frequency is ..... (your ship name)." Traffic frequency --ÇManual set to step y....The transceiver is set
i Announce the following message.
• "PAN PAN"
T: 4567.0kHz IC-M802-1
R: 4567.0kHz
T:12345.0kHz IC-M802-2
R:12345.0kHz
...channel, then push [ENT].
****** All ships *******
----
Instruction Manual - Page 36
...DSC menu
******* DSC MENU *******
-------- Position
ÇIndividual
Group
All ships
Position REQ
Distress
Test
RX memory
TX memory
Set up
Exit
SEL
OK
Category selection
****** Individual Category ------- Traffic frequency --ÇManual set
IC-M802-1 123456789
IC-M802-2 123456788
IC-M802-3 123456787
IC-M802-4 123456786
IC-M802-5 123456785
SEL
OK
Manual...memory channel.
...
Instruction Manual - Page 37
... the TX memory described in pages 23 and 43, if desired.
to select the DSC menu. to transmit the
set to the traffic frequency after the call . • The transceiver is set " then push [ENT]. ✔ When a pre-programmed frequency is ..... (your ship name)."
• The 9-digit identity AND the call . TX:_2134...
Instruction Manual - Page 45
D When receiving a DSC call is received, an acknowledgement must set to DSC watch mode to the calling ...DSC call
One of the following DSC is received depending on the received DSC format (or category):
• Wait for a voice transmission on the category.
*
Individual
*
*
ICOM M802
*
7
* * * *E*x*i*t* * * * *T*r*a*f*f*i*c* * * * * *
*
Position REQ
*
*
ICOM M802...
Instruction Manual - Page 48
... the all ships call in distress or urgency is sent in your part.
I Geographical area call
NOTE: The IC-M802 will not function for an announcement from the calling station. •...*
*
ICOM M802
*
Exit
Traffic
Calling station's name appear when the same ID is not connected to [GPS] and you haven't input the position information manually. r Push [FREQ/CH] to return to DSC watch mode...
Instruction Manual - Page 49
...41 Comply --------
ÇNo reason given
Busy
Channel unable
Mode unable
Operator unavailable
No operator
Station barred...DSC watch mode when "Unable" is selected, go to step t.
to comply
8
push [ENT]. Call --------Category:Routine
call is displayed as above, push [ENT] to display the calling contents. • The received call or not from "Able" and "Unable," then
To:ICOM M802...
Instruction Manual - Page 50
... contents for acknowledgement preparation.
****** RX memory Position REQ ----From:ICOM M802 RX Freq:TX 12345.0kHz
RX 12345.0kHz
Cancel
ACK
e Verify your position and time, then push [ENT]. • When the position or time requires a change, use the keypad and [CH] for settings. • [CH] moves the cursor.
***** Position ACK ***** ---
Latitude 34...
Instruction Manual - Page 52
...; The address/group ID setup screen is displayed beside "" indication when 100 ID codes have been programmed.
Delete any unnecessary IDs in such cases (see p. 46 for the programmed ID confirmation.
******** Set up Address ID Set up Group ID ------Ç
ICOM M802 012345678
SEL
C an c e l
OK
y Push [MODE SET] to return to DSC watch mode, or push [FREQ...
Instruction Manual - Page 54
... [ENT]. • Push [DSC] to select DSC watch mode, or push [FREQ/CH] to return to the select screen.
******** Set up MMSI check ------ Name:ICOM M802 ID:012345678 TX: 2345.0kHz RX: 2345.0kHz
DEL
OK
******** Set up Call frequency Set up Traffic frequency ---
******** Set up " then push [ENT].
w Rotate [CH] to the appropriate memory list screen.
➥ When...
Instruction Manual - Page 72
... have the capabilities of the antenna system. Incapsulated lead keels with radio wave transmissions on the sideband
64
set -up the other marine installations, stainless steel tanks, copper ...system.
SURFACE AREA
For marine SSB radios a good radio frequency ground system will also lead to "hot mikes" where the operator actually receives a radio frequency burn each underwater metal...
Instruction Manual - Page 73
...problems you some additional underwater surface area. 14 ANTENNA AND GROUNDING CONSIDERATIONS
terline ground system and attached directly to each piece of their electronics!
While this close proximity keel bolt for any other electronics onboard with a remote tuner that white fiber glass whip or installing... of Loran weather fax and marine single sideband sets don't provide...
Icom M802 Reviews
We have not received any reviews for Icom yet.