JET Tools JLP-075A-5 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools JLP-075A-5 manuals!
Problems with JET Tools JLP-075A-5?
Ask a Question
Free JET Tools JLP-075A-5 manuals!
Problems with JET Tools JLP-075A-5?
Ask a Question
Popular JET Tools JLP-075A-5 Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
JLP-A Series Manual Lever Hoists/Pullers
1/4- M-187505 Revision B1 12/2014 Copyright © 2014 JET to 6-Ton
JLP-25A 1/4-ton
JLP-75A 3/4-ton
(models shown are representative of the series)
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No.
User Manual - Page 2
... NOT APPLY TO YOU. The specifications listed in Canada by calling 1-800-274-6846. Product Listing with your product or on the JET website. Woodworking Machinery Limited Lifetime - Manual Hoist Accessories; References in this document to JET also apply to provide proof of our tools needs service or repair, please contact Technical Service by a 90 day limited warranty...
User Manual - Page 3
Parts List...15 JLP-50A - Parts List...20 JLP-150A - Parts List...24 JLP-600A - Parts List...22 JLP-300A - Table of Contents
Warranty and Service...2 Table of Contents ...3 Introduction ...5 Specifications (JLP-25A, -50A) ...6 Specifications (JLP-75A, -150A, -300A, -600A) ...7 Unpacking ...8
Contents of the Carton ...8 Installation ...8 Pre-Operation Inspection ...8
Inspecting the Chain...8 ...
User Manual - Page 4
... all internal maintenance and inspections to lift, support or transport people; Do not strike the lever with factory replacement chain only. Do not use more than its intended use this product to a qualified JET service center. 20. Do not place yourself or other such device. 9. If this manual. 3. Always inspect the lever hoist for use...
User Manual - Page 5
...The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to provide consistent, long-term operation if used in minor injury and/or possible tool damage. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. The JLP...
User Manual - Page 7
... 3 Ton models are representative;
NOTE: The above stock numbers are available with slip clutch overload protection. chain is available in .)
"A"
Lbs. Specifications (JLP-75A, -150A, -300A, -600A)
Stock Number
Description
187606 JLP-75A-5 187607 JLP-75A-10 187608 JLP-75A-15 187609 JLP-75A-20 287606 JLP-75AWO-5 * 187610 JLP-150A-5 187611 JLP-150A-10 187612 JLP-150A-15 187613 JLP-150A...
User Manual - Page 8
....
8
Figure 1 Features and Terminology
Figure 2 Whatever method of suspension is chosen, the support components must be hook, clevis pin, trolley, or beam clamp. See Figure 2 for set-up, maintenance and safety instructions. Never extend load chain by properly licensed professional installers. Contents of the lever hoist. Do not use a chain that the chain does...
User Manual - Page 9
... designed, manufactured, and tested for proper operation before resistance or gearing is felt.
The brake mechanism must be replaced by the distance the handle travels before putting into service.
5. Free play is measured by a JET authorized service center.
3. Use of other signs of deformation or damage. If these sounds are worn and should be...
User Manual - Page 10
Figure 4 Figure 5
Figure 6
10 Set the top hook securely.
2. Incorrect loading is no load.) Take up slack by pulling on the bottom hook (Figure 4). ... the centerline (C, Figure 5).
• Never load the hook sideways (D, Figure 5).
3. or in angled or horizontal position as a hoist; Operation
The JLP Lever Hoist may be lifted. Avoid lifting one load with the proper lift capacity.
User Manual - Page 12
...repair...at the factory and should ever be needed, this must be replaced with a new one.
Maintenance
The lever hoist should be ...Carefully inspect the entire load chain. They are available for your JET lever hoist, in 1-1/2 ton and 3 ton load sizes. As...Overload Protection
Some models of the JLP Lever Hoist have overload protection in the form of a slip clutch (these are installed out-of 30...
User Manual - Page 20
...-31 Stripper ...1 32 JLP75A-32 Chain Guide Plate 1 34 JLP75A-34 Gear Side Plate Assembly 1 Gear Side Plate 1 Bearing Race 1 Bushing...2 35 JLP75A-35 Load Gear...1 JLP75A-35A Load Gear (s/n 120604733 and higher 1 36 JLP75A-36 Snap Ring 26 mm 1 38 JLP75A-38 Spur Gear Assembly 2
20 Parts List
Index No. JLP-75A -
User Manual - Page 22
... 1 31 JLP150A-31 Stripper ...1 32 JLP150A-32 Chain Guide Plate 1 34 JLP150A-34 Gear Side Plate Assembly 1 Gear Side Plate 1 Bearing Race 1 Bushing...2 35 JLP150A-35 Load Gear...1 JLP150A-35A Load Gear (s/n 120606750 and higher 1 36 JLP150A-36 Snap Ring 30 mm 1 38 JLP150A-38 Spur Gear Assembly 2
22
JLP-150A - Part No.
User Manual - Page 24
... 6T 1 JLP300A-28A Load Sprocket (3T, 6T) (s/n 12043550 and higher 1 29 JLP300A-29 Roller Set (Right and Left) (3T, 6T 5x6 mm 60 30 JLP300A-30 Driving Pinion (3T, 6T 1... 31 JLP300A-31 Stripper (3T, 6T 1 32 JLP300A-32 Chain Guide Plate (3T, 6T 1 34 JLP300A-34 Gear Side Plate Assembly (3T, 6T 1 Gear Side ... Assembly (3T, 6T 2
24 Part No.
JLP-300A -
User Manual - Page 26
...6T 1 JLP300A-28A Load Sprocket (3T, 6T) (s/n 120615109 and higher 1 29 JLP300A-29 Roller Set (Right and Left) (3T, 6T 5x6 mm 60 30 JLP300A-30 Driving Pinion (3T, 6T... 1 31 JLP300A-31 Stripper (3T, 6T 1 32 JLP300A-32 Chain Guide Plate (3T, 6T 1 34 JLP300A-34 Gear Side Plate Assembly (3T, 6T 1 Gear Side...(3T, 6T 2
26 Part No. JLP-600A - Parts List
Index No.
User Manual - Page 28
Ordering Parts
To order parts or reach our service department, call will allow us to serve you quickly and accurately.
427 New Sanford Road LaVergne, Tennessee 37086
Phone: 800-274-6848 www.jettools.com 28 Having the Model Number and Serial Number of your hoist available when you call 1-800-274-6848, Monday through Friday (see our website for business hours, www.jettools.com).
JET Tools JLP-075A-5 Reviews
We have not received any reviews for JET Tools yet.